Technical Information CC0-CHILLOUT • LPC Super-I/O Board Document No.
Technical Information CC0-CHILLOUT • LPC Super-I/O Contents About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Edition History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical Information CC0-CHILLOUT • LPC Super-I/O About this Manual This manual is a short form description of the technical aspects of the CC0-CHILLOUT, required for installation and system integration. It is intended for the very advanced user only. Edition History EKF Document Ed. Text # 3254 cc0_tie.wpd Contents/Changes Author Date 1 Technical Information CC0-CHILLOUT English Preliminary edition, to be completed later on jj 6. Nov 03 2 Added table P11 (opt. MIDI header) jj 24.
Technical Information CC0-CHILLOUT • LPC Super-I/O Related Documents For a description of the CPU card, which acts as a LPC controller and carrier board with respect to the CC0-CHILLOUT, please refer to the correspondent CPU user guide, available by download at http://www.ekf.de/c/ccpu/ccpu.html. Nomenclature Signal names used herein with an attached '#' designate active low lines. Trade Marks Some terms used herein are property of their respective owners, e.g.
Technical Information CC0-CHILLOUT • LPC Super-I/O CC0-CHILLOUT Features Feature Summary Form Factor Single size Eurocard (160x100mm2), front panel width 4HP (20.
Technical Information CC0-CHILLOUT • LPC Super-I/O Short Description Available as a companion board to the CC2TANGO, CC5-RAVE, CC7-JAZZ and the CC8BLUES CPU cards, the CC0-CHILLOUT is provided with common legacy I/O ports. Interconnection between the CC0 I/O module and the CPU carrier board is achieved by the LPC (Low Pin Count) interface. As an option, the CC0-CHILLOUT is available with a rugged on-board 2.5-inch hard disk drive.
Technical Information CC0-CHILLOUT • LPC Super-I/O The CC0-CHILLOUT communicates to the host CPU by means of the LPC interface. This is a multiplexed ISA bus, enabling the superI/O controller chip to emulate the legacy I/O interfaces. Among these are parallel and serial ports, the PS/2 interfaces, and last not least the classic 1.4/2.8MB floppy disk controller.
Technical Information CC0-CHILLOUT • LPC Super-I/O LPC (Low Pin Count) Super I/O LPCT (Top Mounting) LPCB (Bottom Mounting) P10 FDD P12 CC2 CC5 CC7 CC8 FDD P4/5 LPC P1 Block Diagram CC0-CHILLOUT 34 26 external Floppy-Disk FD FAN P6-P9 IRDA KB/MS Game GPIO LPT J1 Spkr ADM 811 COM1 RS-232E SD Block Diagram CC0-CHILLOUT SD J-SER1 Option © EKF SER1 Option ADM 811 Rear I/O J2 MIDI P11 TTL COM2 RS-232E SER2 TTL USB1 J-SER2 USB1 CC2 CC5 CC7 Option 40 IDE1 EN 44 IDE2 Optional
Technical Information CC0-CHILLOUT • LPC Super-I/O Block Diagram CCZ-RIO J1 RS-232-1 (COM1) Rear Panel COM2 Optional Flat Cable Rear Panel COM1 Optional Flat Cable Serial-1 (TTL) 4HP Rear Panel I/O Serial-2 (TTL) Option 8HP Rear Panel I/O J2 Rear I/O Rear I/O Connector CC0-CHILLOUT CCA-LAMBADA RS-232-2 (COM2) Block Diagram CCZ-RIO COM2 Floppy Disk I/F Floppy ZIF 26 GPIO (J1) Floppy 34 GPIO (J2) USB USB Speaker Parallel Printer Fan Control, IRDA I/O MIDI RS-232-2 (J2) Optional Flat Cable
Technical Information CC0-CHILLOUT • LPC Super-I/O LED1 P2 P5 FUSE4 P12 1 P11 1 LED5 1 ST1 FUSE2 P1 LPCT J1 Rear I/O Hard Disk Drive 2.5-Inch Option P3 1 ST2 DVI SIO LED2 © EKF FUSE1 LED3 P10 RJ45 LED4 J2 LED6 Rear I/O J_IDE2 J_SER2 J_SER1 FUSE5 P9 1 USB P4 P8 P7 P6 FUSE3 Top View Component Assembly CC0-CHILLOUT - 10 EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail info@ekf.
Technical Information CC0-CHILLOUT • LPC Super-I/O On-Board Connectors P1 LPC Low Pin Count interface P2 IDE 40-pin header P3 IDE 44-pin header P4 Floppy disk header 34-pin P5 Floppy disk power (opt.) P6..P9 Fan heatsink headers (opt.) P10 MIDI/gameport header (opt.) P11 Midi header (opt.) P12 Floppy disk header 26-pos. ZIF J1 Rear I/O metric connector 5 x 25 brown key J2 Rear I/O metric connector 5 x 22 DVI Re-routing of host CPU front panel video connector analog/digital (opt.
Technical Information CC0-CHILLOUT • LPC Super-I/O Installing and Replacing Components Before You Begin Warnings The procedures in this chapter assume familiarity with the general terminology associated with industrial electronics and with safety practices and regulatory compliance required for using and modifying electronic equipment.
Technical Information CC0-CHILLOUT • LPC Super-I/O Installing the Board Warning This procedure should be done only by qualified technical personnel. Disconnect the system from its power source before doing the procedures described here. Failure to disconnect power, or telecommunication links before you open the system or perform any procedures can result in personal injury or equipment damage.
Technical Information CC0-CHILLOUT • LPC Super-I/O Removing the Board Warning This procedure should be done only by qualified technical personnel. Disconnect the system from its power source before doing the procedures described here. Failure to disconnect power, or telecommunication links before you open the system or perform any procedures can result in personal injury or equipment damage.
Technical Information CC0-CHILLOUT • LPC Super-I/O EMC Recommendations In order to comply with the CE regulations for EMC, it is mandatory to observe the following rules: C The chassis or rack including other boards in use must comply entirely with CE C Close all board slots not in use with a blind front panel C Front panels must be fastened by built-in screws C Cover any unused front panel mounted connector with a shielding cap C External communications cable assemblies must be shielded (shield c
Technical Information CC0-CHILLOUT • LPC Super-I/O Technical Reference - Connectors Caution Some of the connectors provide operating voltage (e.g. 5V and 12V) to devices inside the system chassis, such as fans and internal peripherals. Not all of these connectors are overcurrent protected. Do not use these connectors for powering devices external to the computer chassis.
Technical Information CC0-CHILLOUT • LPC Super-I/O Front Panel Connectors By default, the CC0-CHILLOUT shares a common 8HP (40.6mm) front panel with the associated CPU board. This assembly forms a robust unit for rugged conditions. No front panel I/O is available for the CC0-CHILLOUT, because the CC0 has been designed exclusively for rear I/O. Alternatively the CC6-ACID is available, providing front panel I/O.
Technical Information CC0-CHILLOUT • LPC Super-I/O LPC Connector P1 The LPC connector P1 is mounted either on top, on bottom, or on both sides of the CC0CHILLOUT PCB. This allows to attach the CC0 either on top (EKF standard) or on bottom of the CPU carrier board. P1 (LPT) 1.27mm Socket 2 x 13 1 2 26 1.
Technical Information CC0-CHILLOUT • LPC Super-I/O IDE/ATA Connector P2 P2 (2.54mm Dual Row Pin Header) 1 2 Key 39 40 2.
Technical Information CC0-CHILLOUT • LPC Super-I/O IDE/ATA Connector P3 P3 (2.00mm Header) 1 43 2 44 2.
Technical Information CC0-CHILLOUT • LPC Super-I/O Floppy Disk Connector P4 P4 (2.54mm Header) 1 2 33 34 2.
Technical Information CC0-CHILLOUT • LPC Super-I/O Power Connector P5 P5 1 AMP 171826-4 1 +5V/1.25A 2 GND 3 GND 4 +12V/1.25A The initial purpose of the optional connector P5 was to deliver +5V power to an attached floppy disk drive wired to P4. A suitable cable assembly matching the AMP 171826-4 would be required.
Technical Information CC0-CHILLOUT • LPC Super-I/O Micro Floppy Disc Connector P12 P12 (1mm ZIF Receptacle) 1 26 1mm pitch FFC/FPC receptacle vertical ZIF 26-position 1 +5V 2 index# 3 +5V 4 ds0# 5 +5V 6 dskchg# 7 NC 8 NC 9 drvden0# 10 mtr0# 11 NC 12 dir# 13 modsel 14 step# 15 GND 16 wdata# 17 GND 18 wgate# 19 GND 20 trk0# 21 NC 22 wrtprt# 23 GND 24 rdata# 25 GND 26 hdsel# In addition to P4, the CC0-CHILLOUT is also provided with a 26-position FFC/FPC ZI
Technical Information CC0-CHILLOUT • LPC Super-I/O Fan Heatsink Header P6..P9 P6 - P9 (2.54mm Pin Row) 1 GND 2 +12V 3 Control 2.54mm 1 GND 2 +12V 3 Tachometer (P6/P7) Pulse Width Modulation (P8/P9) MIDI/Gameport Header P10 P10 (2.54mm Header) 1 2 15 16 2.54mm 5V 1 2 5V joy1but1 3 4 joy2but1 joy1x 5 6 joy2x GND 7 8 midi_out GND 9 10 joy2y joy1y 11 12 joy2but2 joy1but2 13 14 midi_in GND 15 16 NC MIDI Header P11 P11 (2.
Technical Information CC0-CHILLOUT • LPC Super-I/O Rear I/O J1/J2 a b c d e f 25 a b c d e f J2 Rear I/O 2mm Metric Connector J1 Rear I/O 2mm Hard Metric Connector 22 1 1 - 25 EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail info@ekf.de • Internet www.ekf.
Technical Information CC0-CHILLOUT • LPC Super-I/O #J1 A B 25 +5V 24 IDE_d08 +5V 23 +3.3V 22 C D E +3.3V +5V VI/O IDE_reset# IDE_d07 IDE_d09 IDE_d10 +5V IDE_d06 IDE_d11 GND +3.3V IDE_d04 IDE_d05 21 +3.3V IDE_d12 IDE_d13 M66EN (GND) IDE_d03 20 IDE_d14 GND VI/O IDE_d01 IDE_d02 19 +3.3V IDE_d15 IDE_dmarq GND IDE_d00 18 IDE_dmack# GND +3.3V IDE_ior# IDE_iow# 17 +3.3V IDE_a1 IDE_cblid# GND IDE_iordy 16 IDE_a2 GND VI/O IDE_a0 IDE_intrq 15 +3.
Technical Information CC0-CHILLOUT • LPC Super-I/O #J2 A B C D E 22 GPIO21 GPIO22 GPIO43 GPIO60 GPIO61 21 COM1_ri GND COM2_ri COM2_cts FD_drvden0# 20 COM1_cts GND COM2_rxd GND FD_drvden1# 19 GND GND COM2_dsr COM2_dcd FD_index# 18 COM1_rxd COM1_dsr COM2_dtr GND FD_mtr0# 17 COM1_dcd GND COM2_rts COM2_txd FD_ds0# 16 COM1_dtr COM1_rts SER2_ri GND FD_dir# 15 COM1_txd GND SER2_cts SER2_rxd FD_step# 14 SER1_ri SER1_cts SER2_dsr GND FD_wdata# 13 SER1_rxd
Technical Information CC0-CHILLOUT • LPC Super-I/O RS-232E Transceivers The Super-I/O chip provides two asynchronous serial ports (TTL level), which are passed via the J2 rear I/O connector to a rear I/O transition module. Furthermore, the CC0-CHILLOUT is optionally provided with two serial transceivers according to RS-232E. As with the TTL level serial port signals, also the RS-232 transmission lines are wired to the J2 rear I/O connector for usage on a transition module (back panel COM port connectors).
Technical Information CC0-CHILLOUT • LPC Super-I/O Schematics Complete circuit diagrams for this product are available for customers on request. Signing of a non-disclosure agreement would be needed. Please contact sales@ekf.de for details. EKF reserves the right to refuse distribution of confidential information material for any reason that EKF may consider substantial. - 29 EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax.
Technical Information CC0-CHILLOUT • LPC Super-I/O EKF Elektronik GmbH Philipp-Reis-Str. 4 59065 HAMM Germany Fax. +49 (0)2381/6890-90 Tel. +49 (0)2381/6890-0 Internet www.ekf.de E-Mail info@ekf.
