CONTENTS Chapter 1 Features and Overview 1-1 Features 1-2 Buttons and Indicators 1-3 Basic operation of Adjustment menu and the icon list Chapter 2 Settings and Adjustments 2-1 Utility Disk 2-2 Screen Adjustment 2-3 Color Adjustment 2-4 Adjusting Sharpness 2-5 Setting Enable/Disable for the automatic brightness adjustment function Important 2-6 Turning off the monitor automatically Please read PRECAUTIONS, this User’s Manual, and the Setup Manual (separate volume) carefully to familiarize yourself with
This product has been adjusted specifically for use in the region to which it was originally shipped. If operated outside this region, the product may not perform as stated in the specifications. Copyright© 2007-2012 EIZO NANAO CORPORATION All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO NANAO CORPORATION.
Notice for this monitor This product is suited to general purposes like creating documents, viewing multimedia content. This product has been adjusted specifically for use in the region to which it was originally shipped. If the product is used outside the region, it may not operate as specified in the specifications. This product may not be covered by warranty for uses other than those described in this manual.
CONTENTS Notice for this monitor............................................... 1 To use the monitor comfortably................................ 1 Chapter 1 Features and Overview...................... 3 2-6 Turning off the monitor automatically [Off Timer]....................................................... 18 2-7 Locking Buttons [Key Lock] [Menu Lock].... 19 2-8 Displaying Monitor Infomation [Info1] [Info2]...................................................
Chapter 1 Features and Overview Thank you very much for choosing an EIZO color LCD monitor. 1-1 Features • Over drive circuit for clear motion pictures • Dual-input system (DVI-D, D-sub) Note • The stand of the unit can be replaced with an arm or another stand. (Refer to “5-1 Attaching an Arm” on page 26.
1-2 Buttons and Indicators Adjustment menu Button 1 1. 2. 3. 4. 5. 6. 7. 8.
1-3 Basic operation of Adjustment menu and the icon list Basic operation of Adjustment menu Displaying the adjustment menu Pressing the function button to change the setting or pressing allows you to display the adjustment menu. When pressing the input signal selection, mode, brightness control, or volume control button When pressing the menu button Modifying the setting The operation methods differ depending on the icons.
Adjustment menu icon list Icon Function — Overview Determines the setting. Selecting the icon repeatedly allows you to close the adjustment menu. Analog AutoSize Flickering, screen position, and screen size are adjusted automatically. Returns to the pre-adjusted status. Determines the adjustment. Every color gradation (0 to 255) can be displayed by adjusting the signal output level. AutoRange Returns to the pre-adjusted status. Determines the adjustment.
Icon Function Overview Settings Language Selects a language for the adjustment menu or displaying message. The language setting is toggled by selecting the icon. PowerSave Bright Reg The sensor on the front side of the monitor detects the environmental brightness to adjust the screen brightness automatically and comfortably by using the BrightRegulator function. The Enable/Disable setting is toggled by selecting the icon. Sets the power indicator (blue) ON/ OFF in the monitor ON condition.
Chapter 2 Settings and Adjustments 2-1 Utility Disk An “EIZO LCD Utility Disk” (CD-ROM) is supplied with the monitor. The following table shows the disk contents and the overview of the application software programs. ● Disk contents and software overview The disk includes color profiles, application software programs for adjustment, and User’s Manual. Refer to “Readme. txt” or the “read me” file on the disk for software startup procedures or file access procedures.
● To use ScreenManager Pro for LCD For the installation and use of ScreenManager Pro for LCD, refer to its User’s Manual on the disk. To adjust the monitor using ScreenManager Pro for LCD, connect a PC to the monitor with the supplied USB cable. [Connection] (1) Connect the USB port (downstream) of a USB compatible PC (or other USB hub) and the monitor’s USB port (upstream) with the supplied USB cable. (2) The USB function is set up automatically upon connection of the USB cable.
2-2 Screen Adjustment Digital Input When digital signals are input, images are displayed correctly based on the preset data of the monitor. When performing the advanced adjustment, see “2-3 Color Adjustment” (page 13) and its subsequence pages. Analog Input The monitor screen adjustment is used to suppress flickering of the screen or adjust screen position and screen size correctly according to the PC to be used.
3 Perform the AutoSize adjustment again with the analog screen adjustment pattern displayed. ● To adjust flickering, screen position, and screen size automatically [AutoSize] (1) Display Pattern 1 in full screen on the monitor using the “Screen Adjustment Utility” or the screen adjustment pattern files. (2) Press . The adjustment menu appears. (3) Select (4) Select (Analog). (AutoSize). Flickering, screen position, and screen size are adjusted automatically.
● To correct screen position [Position] (Position). (1) Select (2) Adjust the position with (Left) / (Right) / (Down) / (Up) to display the image properly in the display area of the monitor. (3) Select . The adjustment is completed. 5 Adjust the color gradation. ● To adjust color gradation automatically [AutoRange] Every color gradation (0 to 255) can be displayed by adjusting the signal output level.
2-3 Color Adjustment ● To select the display mode (FineContrast mode) FineContrast allows you to select the best display mode easily according to the monitor’s application. FineContrast mode Mode Purpose (CUS) Custom mode. Available to change all setting values. (sRGB) sRGB mode. Suitable for color matching with sRGB compatible peripherals. (TXT) Text mode. Suitable for displaying texts for word processing or spreadsheets. (PIC) Picture mode.
● To perform advanced adjustments Attention Independent setting and saving of color adjustment are available for each FineContrast mode. ● Adjustment items in each mode According to the FineContrast mode selected, the adjustable function differs.
● To adjust the contrast [Contrast] Note • You can also adjust the contrast by pressing while the adjustment menu is not displayed, and press or of (Contrast). • In the contrast of 50%, every color gradation is displayed. • When adjusting the monitor, it is recommended to perform the brightness adjustment which may not lose the gradation characteristics, prior to the contrast adjustment. Perform the contrast adjustment in the following cases.
● To adjust the color temperature [Temperature] Note The color temperature can be adjusted. The color temperature is normally used to express the hue of “White” and/or “Black” by a numerical value. The value is expressed in degrees “K” (Kelvin). In the same way as the flame temperature, the image on the monitor is displayed reddish if the color temperature is low and is bluish if the color temperature is high. The gain preset values are set for each color temperature setting value.
● To adjust the hue [Hue] Attention • This function does not enable to display every color gradation. This function allows you to adjust the hue. If you set the hue to a high value, the image turns greenish. If low, the image turns purplish. Adjustable range: -100 to 100 (1) Press Note • You cannot adjust the value if the icon is not displayed, depending on the FineContrast mode selected. (See “Adjustment items in each mode” on page 14.) . The adjustment menu appears.
2-4 Adjusting Sharpness [Sharpness] This function allows you to emphasize the outline of the image by emphasizing the color difference between the pixels composing the image and to improve a sense of quality and materiality. Contrarily, this function allows you to show the image smoothly by blurring the outline of the image. Adjustable range: -3 to 3 (1) Press . The adjustment menu appears. (2) Select (Screen). (3) Adjust the sharpness with (4) Select . or of (Sharpness).
2-7 Locking Buttons [Key Lock] [Menu Lock] This function allows you to lock the operation buttons to prevent changing the adjusted/set status. Key Lock : Locks the buttons other than the Power button. Menu Lock : Locks the buttons other than the Power, Input signal selection, Brightness control, and Volume control buttons. (1) Press (2) Press to turn off the monitor. holding down to turn on the monitor. The adjustment menu appears. (3) Each time you press , the mode is switched.
2-10 Setting Power Indicator ON/OFF [Power LED] This function allows you to set the power indicator (blue) ON/OFF in the monitor ON condition. (1) Press . The adjustment menu appears. (2) Select (PowerSave). (3) The On/Off setting is toggled by selecting (Power LED). On Off (4) Select . The mode selected is set. 2-11 Setting Language [Language] This function allows you to select a language for the adjustment menu or displaying message.
2-13 Resuming the Default Setting [Reset] There are two types of Reset. One is to reset the color adjustment only to the default settings, and the other is to reset all the settings to the default settings. Attention • After resetting, you cannot undo the operation. ● To reset color adjustment values Only the adjustment values in the current FineContrast mode will revert to the default settings (factory settings). (1) Press . The adjustment menu appears. (2) Select (3) Select (Tool). (Reset).
Chapter 3 Connecting Cables 3-1 Connecting Two PCs to the Monitor Two PCs can be connected to the monitor through the DVI-D and the D-Sub mini 15 pin connector on the back of the monitor. Connection examples DVI-D connector To PC 1 D-Sub mini 15-pin Connector To PC 2 D-Sub mini 15-pin Connector DVI-D connector Signal cable (Digital) FD-C39 Signal cable MD-C87 ● To switch the input signal The input signal switches each time is pressed.
● Setting auto-selection of the input signal [Input Signal] Enable : When either PC is turned off or enters the power-saving mode, the monitor automatically displays signals of another PC. Disable : The monitor does not detect the PC’s signals automatically. Switch an input signal with . (1) Press Note • When “Enable” is selected for [Input Signal], the monitor’s power-saving function works only when the two PCs are in the power-saving mode. . The adjustment menu appears. (2) Select (Tool).
Chapter 4 Troubleshooting If a problem still remains after applying the suggested remedies, contact your local dealer. • • • • • No-picture problems → See No.1 - No.2. Imaging problems (digital input) → See No.3 - No.9. Imaging problems (analog input) → See No.3 - No.12. Other problems → See No.13 - No.15. USB problems → See No.16. Problems 1. Possible cause and remedy No picture • Power indicator does not light. • Check whether the power cord is connected correctly.
Problems Possible cause and remedy 7. Interference patterns or pressure marks remain on • Leave the monitor with a white or black screen. The the screen. symptom may disappear. 8. The outline of the letters are colored. • If the [Sharpness] setting is set to a high level, the characters displayed on the monitor may be colored. 9. Noise appears on the screen. • When entering the signals of HDCP system, the normal images may not be displayed immediately. 10. Display position is incorrect.
Chapter 5 Reference 5-1 Attaching an Arm The stand can be removed and replaced with an arm (or another stand) to be attached to the monitor. Use an arm or stand of EIZO option. [Attaching] 1 Lay the LCD monitor on a soft cloth spread over on a stable surface with the panel surface facing down. 2 Remove the stand. (Prepare a screwdriver.) 3 Attach the monitor to the arm or stand. 26 Unscrew the four screws securing the unit and the stand with the screwdriver.
5-2 Power Saving Mode ■ Analog input This monitor complies with the VESA DPMS standard. [Power Saving System] Attention PC Monitor Operating Power saving STAND-BY SUSPENDED OFF Power Indicator Operating Blue Power saving Orange • Unplugging the power cord completely shuts off power supply to the monitor. • Power consumption changes even when a sound input signal is detected. [Resumption Procedure] • Operate the mouse or keyboard to resume the normal screen.
5-4 Specifications LCD Panel 19-inch (480 mm) TFT color LCD with anti-glare Viewing angle: Horizontal 178°, Vertical 178° (CR:10 or more) Dot Pitch 0.294mm Horizontal Scan Frequency Analog: 24.8-80kHz Digital: 31-64kHz Vertical Scan Frequency Analog: 50-75Hz (Non-interlace) Digital: 59-61Hz (Non-interlace) (VGA TEXT: 69-71Hz) Resolution 1280 dots × 1024 lines Max. Dot Clock Analog: 135MHz Digital: 108MHz Max. Display Color Approx. 16.77 million colors Display Area (H × V) 376.3mm × 301.
Mass Movable range Environmental Conditions USB Main unit (including Tilt stand) 6.0 kg (13.2 Ibs.) Main unit (including Height adjustable stand) 7.2 kg (15.9 lbs.) Main unit (including ArcSwing2 stand) 7.0 kg (15.4 Ibs.) Main unit (including EZ-UP stand) 8.8 kg (19.4 lbs.) Main unit (without stand) 5.2 kg (11.5 lbs.) Tilt stand Tilt: 30° Up, 5° Down Height adjustable stand Tilt: 30° Up, 0° Down Swivel: 35° Right, 35° Left Adjustable height: 100 mm (3.
Outside Dimensions (Tilt stand) unit : mm (inch) 164(6.5) 405(15.9) 378.4(14.9) 13.3(0.52) 1(0.04) 30° 15.5 (0.61) 1(0.04) TILT 5° 152.5(6.0) 80.1(3.15) 75.2 (2.96) 100(3.9) 152.5(6.0) 65.1(2.56) 131.8(5.2) 117(4.8) 100(3.9) 117(4.8) 247.1(9.7) 303(11.9) 334(13.1) 414.1(16.3) 15.5 (0.61) 1(0.04) 1(0.04) 13.3 (0.52) 205(8.1) 42.5(1.67) 38.5(1.52) 61.5(2.42) 374(14.7) 370(14.6) 38.8(1.53) 240.4(9.5) 46 (1.81) Outside Dimensions (Height adjustable stand) 374(14.7) 370(14.6) 172(6.
φ240(9.5) 1(0.04) 13.3(0.52) TILT 60.5 (2.38) 246.8(9.7) 256.1(10.1) 277.6(10.9) 65.1(2.56) 131.8(5.2) 117(4.8) 100(3.9) 117(4.8) 172° 172° SWIVEL 5° 65.1(2.56) 131.8(5.2) 117(4.6) 100(3.9) 117(4.6) 289(11.4) 13.3(0.52) 233~256(9.2~10.1) 347(13.7) 432(17.0) 89(3.5) 66(2.6) 38.5(1.52) 36.1(1.42) 61.5(2.42) φ200(7.9) 374(14.7) 370(14.6) 180.7~340(7.1~13.4) 516.7(20.3) 405(15.9) 378.4(14.9) 1(0.04) 15.5 (0.61) SWIVEL 68. 1(0.04) ° 346.7(13.6) 303(11.9) 334(13.1) 288~423.5(11.3~16.7) 1(0.
Connector Pin Assignment • DVI-D connector Pin No. Signal Pin No. Signal Pin No. Signal 1 T.M.D.S. Data 2- 9 T.M.D.S. Data1- 17 T.M.D.S. Data0- 2 T.M.D.S. Data 2+ 10 T.M.D.S. Data1+ 18 T.M.D.S. Data0+ 3 T.M.D.S. Data2/4 Shield 11 T.M.D.S. Data1/3 Shield 19 T.M.D.S. Data0/5 Shield 4 NC* 12 NC* 20 NC* 5 NC* 13 NC* 21 NC* 6 DDC Clock (SCL) 14 +5V Power 22 T.M.D.S. Clock shield 7 DDC Data (SDA) 15 Ground (return for +5V, Hsync, and Vsync) 23 T.M.D.S.
5-5 Glossary Clock The analog input monitor needs to reproduce a clock of the same frequency as the dot clock of the graphics system in use, when the analog input signal is converted to a digital signal for image display. This is called clock adjustment. If the clock pulse is not set correctly, some vertical bars appear on the screen.
Resolution The LCD panel consists of numerous pixels of specified size, which are illuminated to form images. This monitor consists of 1280 horizontal pixels and 1024 vertical pixels. At a resolution of 1280 x 1024, all pixels are illuminated as a full screen (1:1). sRGB (Standard RGB) International standard for “color reproduction and color space” among peripheral devices (such as monitors, printers, digital cameras, scanners).
5-6 Preset Timing The following table shows factory preset video timing (for analog signal only). Mode Dot clock VGA 640×480@60Hz 25.2 MHz VGA 720×400@70Hz 28.3 MHz Macintosh 640×480@67Hz 30.2 MHz Macintosh 832×624@75Hz 57.3 MHz Macintosh 1152×870@75Hz 100.0 MHz Macintosh 1280×960@75Hz 126.2 MHz VESA 640×480@72Hz 31.5 MHz VESA 640×480@75Hz 31.5 MHz VESA 800×600@56Hz 36.0 MHz VESA 800×600@60Hz 40.0 MHz VESA 800×600@72Hz 50.0 MHz VESA 800×600@75Hz 49.5 MHz VESA 1024×768@60Hz 65.
Congratulations! The display you have just purchased carries the TCO’03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also minimizes the Impact on our natural environment.
For U.S.A. , Canada, etc. (rated 100-120 Vac) Only FCC Declaration of Conformity We, the Responsible Party EIZO NANAO TECHNOLOGIES INC. 5710 Warland Drive, Cypress, CA 90630 Phone: (562) 431-5011 declare that the product Trade name: EIZO Model: FlexScan S1932 is in conformity with Part 15 of the FCC Rules.
Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor Dieser Monitor ist für Bildschirmarbeitsplätze vorgesehen. Wenn nicht der zum Standardzubehör gehörige Schwenkarm verwendet wird, muss statt dessen ein geeigneter anderer Schwenkarm installiert werden.
4th Edition-March, 2012 03V22195D1 (U.
