Installation manual

Contents Diamond digital
II
Page Page
6. Initial installation 61. . . . . . . . . . . . . . . . . . . . .
6.1 Installation checklist 61. . . . . . . . . . . . . .
6.2 Powerup of the switcher 62. . . . . . . . . . .
6.3 Input processor RY1900 65. . . . . . . . . .
6.4 ME processor RY1903 66. . . . . . . . . . . .
6.5 Key processor RY1906 67. . . . . . . . . . .
6.6 Wipe processor RY1908 70. . . . . . . . . .
6.7 Output processor RY1911 71. . . . . . . . .
6.8 Controller RY1917 72. . . . . . . . . . . . . . .
6.9 Store RY1913 73. . . . . . . . . . . . . . . . . . .
6.10 System messages and adjustments 74
6.10.1 Control panel controller
RY1821/RY1822 74. . . . . . . . . .
6.10.2 E-box controller
RY1601/RY1917 77. . . . . . . . . .
6.10.3 Fader connector panel
RC1855 81. . . . . . . . . . . . . . . . . .
6.10.4 Timing/Genlock aligment 82. . .
6.10.5 Genlock adjust. with menu 84. .
6.11 Diamond digital-Software update 86. . .
6.12 Loading flash software from
DD floppy disk drive 94. . . . . . . . . . . . . .
7. Description of the interfaces 97. . . . . . . . . .
7.1 Cheapernet specification 97. . . . . . . . . .
7.2 Router inreface with BTS-
ASCII-Protocol 98. . . . . . . . . . . . . . . . . . .
7.2.1 General 98. . . . . . . . . . . . . . . . . .
7.2.2 Interfaces 99. . . . . . . . . . . . . . . .
7.2.3 Connection cables 100. . . . . . . .
7.2.4 Menu settings 101. . . . . . . . . . . .
7.3 Ident X-bar interface 108. . . . . . . . . . . . .
7.4 Aux panel and under monitor
display installation 110. . . . . . . . . . . . . .
7.5 Connection of the status
displays RP 1/2 UMD 113. . . . . . . . . . .
7.6 Tally and GPI interface 117. . . . . . . . . .
7.7 Function of tally in connectors 124. . . .
8. DVE and editors 125. . . . . . . . . . . . . . . . . . . . .
8.1 Technical setup and wiring 125. . . . . . .
8.2 Preparations at the DVE device 126. . .
8.3 Device specific notes 127. . . . . . . . . . .
8.3.1 Pinnacle prizm 127. . . . . . . . . . .
8.3.2 ABEKAS A-57 VTR protocol 128
8.3.3 ABEKAS A-57
RS232 protocol 129. . . . . . . . . .
8.3.4 ABEKAS A53D 130. . . . . . . . . .
8.3.5 QUESTECH charisma 131. . .
8.3.6 GVG DPM 700 132. . . . . . . . . .
8.3.7 AMPEX ADO 100/500/1000 134
8.4 DVE control 135. . . . . . . . . . . . . . . . . . . .
8.5 Editors with GVG-200 o/e protocol 139
8.6 Editors with GVG-100 protocol only 139
8.7 Port protocols in the
diamond digital switchers 140. . . . . . . . .
8.8 System intergration DD5/DD10 141. . .
8.9 System intergration DD20/DD30 142 . .
9. Port protocols GVG-200 emulation 143 . . .
9.1 Crosspoint bus command C1-C4 143. .
9.2 Analog control 144. . . . . . . . . . . . . . . . . .
9.3 Key (button) commands 145. . . . . . . . . .
9.4 Key commands 147. . . . . . . . . . . . . . . . .
9.4.1 Borderline mode command
(B0/B1) 147. . . . . . . . . . . . . . . . .
9.4.2 Key accumulation command
(BF/CO) 147. . . . . . . . . . . . . . . .
9.5 Wipe generator commands 148. . . . . . .
9.5.1 Wipe pattern select
command (C8) 148. . . . . . . . . . .
9.5.2 Wipe modulation
command (B5) 148. . . . . . . . . . .
9.5.3 Wipe multiplication
command (B6) 148. . . . . . . . . . .
9.5.4 Wipe rotation
command (B7) 148. . . . . . . . . . .
9.5.5 Transition mode
command (CA) 148. . . . . . . . . . .
9.5.6 Auto transition rate
command (CC, CD) 149. . . . . .
9.5.7 Transition key select (FB) 149.
9.5.8 All stop command (F2) 149. . . .
9.6 Section: E-MEM commands 150. . . . . .
9.6.1 E-MEM LEARN/RECALL
enable command (D8) 150. . . .
9.6.2 LEARN E-MEM
command DA) 150. . . . . . . . . . .
9.6.3 RECALL E-MEM
command (DB) 152. . . . . . . . . . .
10.Block diagrams 153. . . . . . . . . . . . . . . . . . . . .