Important Please read PRECAUTIONS, this User’s Manual, and the Setup Guide (separate volume) carefully to familiarize yourself with safe and effective usage. • Please refer to the Setup Guide for basic information ranging from connection of the monitor to a PC to using the monitor. • The latest User’s Manual is available for download from our web site: http://www.eizo.
Location of Caution Statement This product has been adjusted specifically for use in the region to which it was originally shipped. If operated outside this region, the product may not perform as stated in the specifications. No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
Notice for this monitor This product is suited to general purposes like creating documents, viewing multimedia content. This product has been adjusted specifically for use in the region to which it was originally shipped. If the product is used outside the region, it may not operate as specified in the specifications. This product may not be covered by warranty for uses other than those described in this manual.
Cleaning Attention • Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet or panel, and also quality deterioration of the image. • Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel. Note • The optional ScreenCleaner is recommended for cleaning the cabinet and panel surface. The stains on the cabinet and panel surface can be removed by moistening part of a soft cloth with water.
CONTENTS Cover....................................................................... 1 Notice for this monitor.......................................... 3 Cleaning..................................................................... 4 To use the monitor comfortably.............................. 4 CONTENTS.............................................................. 5 Chapter 1 Introduction........................................ 7 1-1. Features..........................................................
Trademark................................................................ 44 License / Copyright................................................. 44 ENERGY STAR......................................................... 45 TCO........................................................................... 45 FCC Declaration of Conformity............................. 46 Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor.............................47 Hinweis zur Ergonomie :............................
Chapter 1 Introduction Thank you very much for choosing an EIZO color LCD monitor. 1-1. Features • • • • Supports a resolution of 1600 × 1200 IPS panel with 89˚ horizontal and vertical viewing angles Applicable to DisplayPort (applicable to 8 bit) The FineContrast function allows the user to select the display mode optimum to the displayed image. -- The Paper mode reproduces a printed paper effect on the monitor. See “To select the display mode (FineContrast Mode)” (page 14).
1-2. Controls and Functions ●●Front Setting menu*1 1 1. Ambient light sensor 2 3 4 5 6 7 8 9 Detects ambient brightness (Auto EcoView function (page 29)). 2. button Displays the setting menu of the power saving function (Auto EcoView (page 29) and EcoView Optimizer 2 (page 29)). 3. button Switches input signals for display (page 36). 4. button Changes the FineContrast mode (page 14). 5. , button Adjusts the brightness (page 15). 6.
●●Rear 15 13 14 16 10 11 12 10. Power connector Connects the power cord. 11. Input signal connector Left: DisplayPort connector / Center: DVI-D connector / Right: D-Sub mini15-pin connector 12. USB port (UP) Connects the USB cable for using the USB Hub function (page 37). 13. Security lock slot Complies with Kensington’s MicroSaver security system. 14. Stand*2 Adjusts the height and angle (tilt and swivel) of the monitor. 15. USB port (DOWN) Connects a peripheral USB device. 16.
1-4. Basic Operations and Functions ●●Basic operation of the Setting menu 1. Displaying the Setting menu 1. Press . The Setting menu appears. 2. Adjusting / Setting 1. Choose a menu to adjust / set with , , and then press . The Sub menu appears. 2. Choose an item to adjust / set with , , and then press . The adjustment / setting menu appears. 3. Adjust / set the selected item with , , and then press 3. Exiting 1. Choose “Return” from the Sub menu and press 2.
●●Functions The following table shows the Setting menu and setting items of each menu. Main menu Color*1 Screen PowerManager Setting Brightness Contrast Temperature Gamma Advanced Settings Reference “2-3. Adjusting Color” (page 14) Saturation Hue Overdrive Gain Color Reset Screen Size Smoothing Analog Adjustment*2 Auto Screen Adjust Auto Range Adjust Clock Phase Hor.Position Ver.Position Power Save Eco Timer “To reset the color adjustments” (page 27) “Screen Size Changing” (page 24) “2-4.
Chapter 2 Adjusting Screens 2-1. Compatible Resolutions The monitor supports the following resolutions. ●●Analog Input (D-Sub) Resolution Applicable Signals 640 × 400 640 × 480 720 × 400 800 × 600 832 × 624 1024 × 768 1152 × 864 1152 × 870 1280 × 960 1280 × 1024 1600 × 1200*1 PC-9801, PC-9821 AP2 VGA, VESA, MAC VGA TEXT VESA MAC VESA VESA MAC VESA, MAC VESA VESA Vertical Scan Frequency Dot Clock ~70 Hz ~75 Hz 70 Hz ~75 Hz 75 Hz ~75 Hz 75 Hz 75 Hz ~75 Hz ~75 Hz 60 Hz 162 MHz (Max.
2-2. Setting the Resolution When you connect the monitor to the PC and find that the resolution is improper, or when you want to change the resolution, follow the procedure below. ●●Windows 8 / Windows 7 1. For Windows 8, click the “Desktop” tile on the Start Screen to display the desktop. 2. Right-click the mouse anywhere on the desktop except for icons. 3. From the displayed menu, click “Screen resolution”. 4. On the “Screen Resolution” dialog box, select the monitor. 5.
2-3. Adjusting Color ●●To select the display mode (FineContrast Mode) This function allows easy selection of a desired mode according to monitor application. Display Modes Mode User1 Purpose Select this to define a desired set of parameter settings. User2 sRGB Suitable for color matching with sRGB compatible peripherals. Paper Produces a printed paper effect. Suitable for displaying images from media such as books and documents. Movie Suitable for playing back animated images.
●●To perform advanced adjustments The “Color” menu of the Setting menu allows you to set and save the independent color adjustment for each mode. Attention • It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more after the monitor power has been turned on, and then adjust the monitor. • Perform the range adjustment first when adjusting color for analog signals (see “To adjust color gradation automatically” (page 23)).
●●To adjust contrast The brightness of the screen is adjusted by varying the video signal level. Adjustable range 0 to 100 Procedure 1. Choose “Color” in the Setting menu, and press . . 2. Choose “Contrast” in the “Color” menu, and press The “Contrast” menu appears. 3. Use or for adjustment. to exit. 4. Press Note • In the contrast of 50, every color gradation is displayed.
●●To adjust gamma Gamma can be adjusted. The brightness of the monitor varies depending on the input signal, however, the variation rate is not proportional to the input signal. To keep the balance between the input signal and the brightness of the monitor is called as “Gamma correction”. Adjustable range 1.8, 2.0, 2.2 Procedure 1. Choose “Color” in the Setting menu, and press . . 2. Choose “Gamma” in the “Color” menu, and press The “Gamma” menu appears. 3. Use or for adjustment. to exit. 4.
●●To adjust hue This function allows you to adjust hue. Adjustable range -50 to 50 Procedure 1. Choose “Color” in the Setting menu, and press . . 2. Choose “Advanced Settings” in the “Color” menu, and press 3. Choose “Hue” in the “Advanced Settings” menu, and press . The “Hue” menu appears. 4. Use or for adjustment. to exit. 5. Press Attention • Using this function may make some color gradations unavailable for display.
●●To adjust gain The brightness of each color component red, green, and blue is called “Gain”. You can change the hue of “white” by adjusting gain. Adjustable range 0 to 100 Procedure 1. Choose “Color” in the Setting menu, and press . . 2. Choose “Advanced Settings” in the “Color” menu, and press 3. Choose “Gain” in the “Advanced Settings” menu, and press . The “Gain” menu appears. 4. Adjust gain with 5. Press or for each of red, green, and blue. to exit.
2-4. Screen Adjustment ●●Digital Signal Input When digital signals are input, images are displayed correctly based on the preset data of the monitor, but if characters and / or lines appear blurred, go to “To modify blurred characters / lines” (page 23). When performing more advanced adjustment, see “2-3. Adjusting Color” (page 14) and subsequent pages. ●●Analog Signal Input Attention • It takes about 30 minutes for the performance of electrical parts to stabilize.
2. Prepare to use analog screen adjustment patterns. Load the “EIZO LCD Utility Disk” to your PC, and then open the “Screen adjustment pattern files”. Note • For details and instructions on opening the “Screen adjustment pattern files”, refer to the Readme.txt file. 3. Perform the auto adjustment again with the analog screen adjustment pattern displayed. ●●To adjust flickering, screen position, and screen size automatically Procedure 1.
●●To remove flickering or blurring Procedure . 1. Choose “Analog Adjustment” in the “Screen” menu, and press 2. Choose “Phase” in the “Analog Adjustment” menu, and press . The “Phase” menu appears. 3. Adjust the phase with 4. Press or to minimize flickering or blurring. to exit. When vertical bars appear on the screen after adjustment, go back to “To eliminate vertical bars ”.
5. Adjusting color gradation. ●●To adjust color gradation automatically Every color gradation (0 to 255) can be displayed by adjusting the signal output level. Procedure 1. Display Pattern 2 in full screen on the monitor using the “Screen adjustment pattern files”. 2. Choose “Screen” in the Setting menu, and press . 3. Choose “Analog Adjustment” in the “Screen” menu, and press . 4. Choose “Auto Range Adjust” in the “Analog Adjustment” menu, and press 5. Select “Yes” with or , and press . .
2-5. Screen Size Changing ●●Screen Size Changing The image with the resolution other than the recommended resolution is displayed in full screen automatically. You can change the screen size by using the “Screen Size” function. Setting Function Full Screen Displays an image in full screen. Images are distorted in some cases because the vertical rate is not equal to the horizontal rate. Enlarged Displays an image in full screen.
Chapter 3 Setting Monitor 3-1. Enabling / Disabling DDC/CI communication This function allows you to enable / disable the DDC/CI communication (see “Chapter 7 Glossary” (page 42)). Procedure 1. Choose “Monitor Settings” in the Setting menu, and press 2. Choose “DDC/CI” in the “Monitor Settings” menu, and press . . The “DDC/CI” menu appears. 3. Select “On” or “Off” with 4. Press or . to exit. Note • The DisplayPort input of this monitor does not support DDC/CI communication. 3-2.
3-3. Setting Orientation This function allows you to change the orientation of the Setting menu when using the monitor screen in vertical display position. Procedure . 1. Choose “Monitor Settings” in the Setting menu, and press . 2. Choose “Menu Settings” in the “Monitor Settings” menu, and press . 3. Choose “Orientation” in the “Menu Settings” menu, and press The “Orientation” menu appears. 4. Select “Landscape” or “Portrait” with 5. Press or . to exit. 6.
3-6. Setting Language This function allows you to select a language for the Setting menu or messages. Selectable languages English, German, French, Spanish, Italian, Swedish, Japanese, Simplified Chinese, Traditional Chinese Procedure 1. Choose “Monitor Settings” in the Setting menu, and press . 2. Choose “Language” in the “Monitor Settings” menu, and press . The “Language” menu appears. 3. Choose a language with 4. Press or . to exit. 3-7.
Chapter 4 Power Saving Functions 4-1. Setting Power Saving This function allows you to set the monitor into the power saving mode according to the PC status. When the monitor has shifted to the power saving mode, the images on the screen are not displayed. Attention • Unplugging the power cord completely shuts off power supply to the monitor. • When the monitor is in power saving mode, devices connected to the USB downstream port will still work.
4-2. Setting Power Indicator This function allows you to set the power indicator (blue) ON / OFF in the monitor ON condition. Procedure 1. Choose “Monitor Settings” in the Setting menu, and press . . 2. Choose “Power Indicator” in the “Monitor Settings” menu, and press The “Power Indicator” menu appears. 3. Select “On” or “Off” with or . to exit. 4. Press 4-3.
4-4. Checking the power saving level The EcoView menu allows you to check Power Reduction, CO2 Reduction, and Eco Performance Level. The more indicators light up representing the Eco Performance Level, the higher the power saving level attained. Indicator Procedure 1. Press . The “EcoView Menu” menu appears. Note Power reduction: the backlight’s reduction of power consumption as a result of the adjusted brightness value.
Chapter 5 Troubleshooting If a problem still remains after applying the suggested remedies, contact your local EIZO representative. 5-1. No picture Problem 1. No picture • Power indicator does not light. Possible cause and remedy • Check whether the power cord is connected properly. • If the problem persists, turn off the monitor, and then turn it on again a few minutes later. • Power indicator is lighting blue.
Problem 2. The message below appears. • The message shows that the input signal is out of the specified frequency range. Example: Possible cause and remedy This message appears when the signal is not input correctly even when the monitor functions properly. • Check whether the PC is configured to meet the resolution and vertical scan frequency requirements of the monitor (see “2-1. Compatible Resolutions” (page 12)). • Reboot the PC. • Select an appropriate setting using the graphics board’s utility.
5-3. Imaging problems (for digital only) Problem Possible cause and remedy 1. The monitor configuration is changed to single under the multiple monitor configuration (when DisplayPort is connected). • When two monitors are connected to one PC using DisplayPort, and the power to one of the monitors is turned off with the power button, the screen setting may be changed to the single monitor configuration. In such a case, enable the “DP HotPlug” function with the following procedures.
5-5. Other problems Problem 34 Possible cause and remedy 1. The Setting menu does not appear. • Check whether the operation lock function is active (see “3-2. Locking Operation Buttons” (page 25)). 2. The “Smoothing” on the Setting menu “Screen” cannot be selected. • You cannot choose “smoothing” when the screen is displayed in the following resolutions or settings. --The resolution is 1600 × 1200 --The resolution is 800 × 600 --Screen Size is “Normal” 3. The auto adjustment function does not work.
Chapter 6 Reference 6-1. Attaching the Optional Arm An optional arm (or an optional stand) can be attached by removing the stand section. Please refer to our web site for the corresponding optional arm (or optional stand). http://www.eizo.com Attention • When attaching an arm or stand, follow the instructions of their User’s Manual. • When using another manufacturer’s arm or stand, confirm the following in advance and select one conforming to the VESA standard.
6-2. Connecting Multiple PCs The product has multiple connections to PCs and allows you to switch to one of the connections for display.
●●To set input signal selection Setting Function Auto The monitor recognizes the connector through which PC signals are input. When a PC is turned off or enters the power saving mode, the monitor automatically displays another signal. Manual The monitor displays the signal from the selected connector despite the signal input. Select the input signal for display using the operation button. Procedure 1. Choose “Monitor Settings” from the Adjustment menu, and press 2.
●●Connection Procedure (Setup of USB Function) 1. Connect the monitor first to a PC using the signal cable, and run the PC. 2. Connect the USB cable between the USB downstream port of the PC and the USB upstream port of the monitor. The USB hub function is set up automatically upon connection of the USB cable. 3. Connect the peripheral USB devices to the USB downstream port of the monitor. USB downstream port USB upstream port 6-4.
6-5. Specifications LCD Panel Size 21.3-inch (540 mm) Type TFT color LCD, LED backlight Surface treatment Anti-Glare Hard Coating Viewing angles Horizontal 178˚, vertical 178˚ (CR≥10) Dot Pitch 0.270 mm Response Time Black-white-black: Approx. 20 ms Gray-to-gray: Approx.
Environmental Conditions Temperature Humidity Air Pressure USB Operating: 5˚C to 35˚C (41˚F to 95˚F) Transportation/ Storage: -20˚C to 60˚C (-4˚F to 140˚F) Operating: 20 % to 80 % R.H. (no condensation) Transportation/ Storage: 10 % to 90 % R.H. (no condensation) Operating: 700 to 1,060 hPa Transportation/ Storage: 200 to 1,060 hPa Standard USB Specification Revision 2.0 Port Upstream port × 1, Downstream port × 2 Communication Speed 480 Mbps (high), 12 Mbps (full), 1.
●●Accessories Signal cable Cleaning Kit PP2000 EIZO “ScreenCleaner” For the latest information about the accessories, refer to our web site. http://www.eizo.com 6-6. Preset Timing The following table shows factory preset analog signal timing. Attention • Display position may be deviated depending on the PC connected, which may require screen adjustment using Setting menu. • If a signal other than those listed in the table is input, adjust the screen using the Setting menu.
Chapter 7 Glossary Clock The analog signal input monitor needs to reproduce a clock of the same frequency as the dot clock of the graphics system in use, when the analog signal is converted to a digital signal for image display. This is called clock adjustment. If the clock pulse is not set correctly, some vertical bars appear on the screen. DDC/CI (Display Data Channel/Command Interface) VESA provides the standardization for the interactive communication of the setting information, etc.
Overdrive This technology enhances response speed by increasing the potential difference at the time of motion of liquid-crystal pixels, and it is used for liquid-crystal TV sets and others in general. It provides clear-cut three-dimensional display with little afterimage, by improving response speed of the intermediate graduation range that frequently appears in moving images. Phase Phase means the sampling timing to convert the analog input signal to a digital signal.
Appendix Trademark The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing, LLC in the United States and other countries. The DisplayPort Compliance Logo and VESA are registered trademarks of the Video Electronics Standards Association. Acrobat, Adobe, Adobe AIR, and Photoshop are registered trademarks of Adobe Systems Incorporated in the United States and other countries.
ENERGY STAR As an ENERGY STAR Partner, EIZO Corporation has determined that this product meets the ENERGY STAR guidelines for energy efficiency. TCO This product has acquired the TCO standard that relates to the safety, ergonomics (EcoView Optimizer 2: Off), environment and so forth of office equipment. For an overview of the TCO, refer to our web site. http://www.eizo.
FCC Declaration of Conformity For U.S.A. , Canada, etc. (rated 100-120 Vac) Only FCC Declaration of Conformity We, the Responsible Party EIZOInc. 5710WarlandDrive,Cypress,CA90630 Phone:(562)431-5011 declare that the product Tradename:EIZO Model:FlexScanS2133 is in conformity with Part 15 of the FCC Rules.
Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor Dieser Monitor ist für Bildschirmarbeitsplätze vorgesehen. Wenn nicht der zum Standardzubehör gehörige Schwenkarm verwendet wird, muss statt dessen ein geeigneter anderer Schwenkarm installiert werden.
LIMITED WARRANTY LIMITED WARRANTY EIZOCorporation(hereinafterreferredtoas“EIZO”)anddistributorsauthorizedbyEIZO(hereinafterreferredtoasthe “Distributors”)warrant,subjecttoandinaccordancewiththetermsofthislimitedwarranty(hereinafterreferredtoasthe “Warranty”),totheoriginalpurchaser(hereinafterreferredtoasthe“Original Purchaser”)whopurchasedtheproduct specifiedinthisdocument(hereinafterreferredtoasthe“Product”)fromEIZOorDistributors,thatEIZOa
BEGRENZTE GARANTIE EIZO Corporation (im Weiteren als „EIZO“ bezeichnet) und die Vertragsimporteure von EIZO (im Weiteren als „Vertrieb(e)“bezeichnet)garantierendemursprünglichenKäufer(imWeiterenals„Erstkäufer“bezeichnet),derdasin diesemDokumentvorgegebeneProdukt(imWeiterenals„Produkt“bezeichnet)vonEIZOodereinemVertrieberworben hat,gemäßdenBedingungendieserbeschränktenGarantie(imWeiterenals„Garantie“bezeichnet),dassEIZOund derVertriebnacheigenemE
GARANTIE LIMITÉE EIZO Corporation (ci-après dénommé « EIZO ») et les distributeurs autorisés par EIZO (ci-après dénommés « Distributeurs »), sous réserve et conformément aux termes de cette garantie limitée (ci-après dénommée « Garantie »), garantissent à l’acheteur initial (ci-après dénommé « Acheteur initial ») du produit spécifié dans la présente (ci-après dénommé « Produit ») acheté auprès d’EIZO ou de Distributeurs agréés EIZO, que EIZO et ses
GARANTÍA LIMITADA EIZO Corporation (en lo sucesivo “EIZO”) y sus distribuidores autorizados (en lo sucesivo los “Distribuidores”), conarregloydeconformidadconlostérminosdeestagarantíalimitada(enlosucesivola“Garantía”),garantizanal compradororiginal(enlosucesivoel“Comprador original”)quecompróelproductoespecificadoenestedocumento(en losucesivoel“Producto”)aEIZOoasusDistribuidores,queEIZOysusDistribuidores,asupropiocriterio,repararán osus
GARANZIA LIMITATA EIZOCorporation(acuisifaràriferimentodaquiinpoicon“EIZO”)ediDistributoriautorizzatidaEIZO(acuisifarà riferimento da qui in poi con “Distributori”) garantiscono, secondo i termini di questa garanzia limitata (a cui si farà riferimentodaquiinpoicon“Garanzia”)all’acquirenteoriginale(acuisifaràriferimentodaquiinpoicon“Acquirente originale”) che ha acquistato il prodotto specificato in questo documento (a cui si farà rif
BEGRÄNSAD GARANTI EIZOCorporation(nedankallat“EIZO”)ochEIZOsauktoriseradedistributörer(nedankallade“Distributörer”)garanterar ienlighetmedvillkorenidennabegränsadegaranti(nedankallad“Garantin”)denursprungligeköparen(nedankallad den“Ursprunglige köparen”)somköptedenidokumentetspecificeradeprodukten(nedankallad“Produkten”)från EIZOellerDistributörer,attEIZOellerDistributörerenligtegetgottfinnandekostnadsfrittantingenrepareraellerbytaut dendefektaPr
ΠΕΡΙΟΡΙΣΜΕΝΗ ΕΓΓΥΗΣΗ Η EIZO Corporation (στο εξής «EIZO») και οι διανομείς που εξουσιοδοτεί η EIZO (στο εξής «Διανομείς») παρέχουν εγγύηση, υποκείμενη και σύμφωνα με τους όρους της παρούσας περιορισμένης εγγύησης (στο εξής «Εγγύηση»),στοναρχικόαγοραστή(στοεξής«Αρχικός Αγοραστής»)οοποίοςαγόρασετοπροϊόνπουκαθορίζεταιστο παρόνέγγραφο(στοεξής«Προϊόν»)απότηνEIZOήτουςΔιανομείς,ηοποίαεξασφαλίζειότιηEIZOκαιοιΔιανομείς, σύμφωναμετηδιακριτήευχέρειάτ
ОГРАНИЧЕННАЯ ГАРАНТИЯ EIZO Corporation (называемая в дальнейшем “EIZO”) и авторизированные EIZO дистрибуторы (называемые в дальнейшем“Дистрибуторы”)гарантируют,всоответствиисусловиямиипунктамиэтойограниченнойгарантии (называемойвдальнейшем“Гарантия”),первичномупокупателю(называемомувдальнейшем“Первоначальный покупатель”),которыйприобрелуEIZOилиДистрибуторовпродукт,указанныйвэтомдокументе(называемый в дальнейшем “Продукт”), что EIZO или Дистрибуторы на св
有限责任保证书 EIZO Corporation（以下简称 EIZO ）和 EIZO 授权的经销商（以下简称 经销商 ），接受并依照本有限责任保证书（以 下简称 保证书 ）之条款，向从 EIZO 和经销商购买本文中所规定产品（以下简称 产品 ）的原买方（以下称 原买方 ） 提供保证 ：在保证期内（规定如下），如果原买方发现按本产品所附使用说明书（以下简称 用户手册 ）所述方式正常使 用本产品过程中，本产品出现故障或损坏，EIZO 和经销商根据其独自的判断免费修理或更换该产品。 本保证期限定为（i）自本产品购买之日起的五（5）年期间或限定为到达（ii）使用本产品 3 万小时的期限（以下简称 保证期限 ） 。 EIZO 和经销商将不向原买方或任何第三方承担本保证书所规定之外的与本产品有关的任何责任或义务。 本产品的任何部件停产七 (7) 年后，EIZO 和经销商将不再保留或保管任何这类部件。维修显示器时，EIZO 与经销商将使 用符合我方质量控制标准的替换零件。 本保证书仅对于设有经销商的国家或地区有效。本保证书并不限定原买方的任何法律权利。 无论本保证书的任何其他条款如何规定，对于任何下列情况之一，EIZO 和
Recycling Information Recycling Information This product, when disposed of, is supposed to be collected and recycled according to your country’s legislationtoreduceenvironmentalburden.Whenyoudisposeofthisproduct,pleasecontactadistributoror anaffiliateinyourcountry. ThecontactaddresseesarelistedontheEIZOwebsitebelow. http://www.eizo.com ForrecyclinginformationforcustomersinSwitzerland,pleaserefertothefollowingwebsite. http://www.swico.
Πληροφορίες ανακύκλωσης Τοπροϊόναυτό,όταναπορρίπτεται,πρέπεινασυλλέγεταικαιναανακυκλώνεταισύμφωναμετηνομοθεσία τηςχώραςσαςέτσιώστεναμηνεπιβαρύνειτοπεριβάλλον.Γιανααπορρίψετετοπροϊόν,επικοινωνήστεμε έναναντιπρόσωποήμιαθυγατρικήεταιρείαστηχώρασας. ΟιδιευθύνσειςεπικοινωνίαςαναγράφονταιστηντοποθεσίαwebτηςEIZOπαρακάτω. http://www.eizo.
Informace o recyklaci Při likvidaci produktu musí být produkt vyzvednut a recyklován podle zákonů příslušné země, aby nedocházelo k zatěžování životního prostředí. Zbavujete-li se produktu, kontaktujte distributora nebo pobočkuvesvézemi.KontaktníadresyjsouuvedenynanásledujícíwebovéstráncespolečnostiEIZO. http://www.eizo.com Ringlussevõtu alane teave Keskkonnakoormusevähendamisekstulekskasutatudtootedkokkukogudajavõttaringlussevastavaltteie riigiseadustele.
Информация относно рециклиране Приизхвърлянетонатозипродуктсепредлагасъбиранетоирециклиранетомусъобразнозаконитена вашатастраназадасенамализамърсяванетонаоколнатасреда.Когатоискатедасеосвободитеот тозипродукт,молясвържетесестърговскиямупредставителилисъссъответнитеорганиотговарящи затовавъввашатастрана. ДаннитезавръзкаснассаописанинаследнияИнтернетсайтнаEIZO: http://www.eizo.
China Measures for RoHS Compliance in ChinaRoHS 关于电子信息产品污染控制标识 本标识根据「电子信息产品污染控制管理办法」，适用于在中华人民共和国销售的电子信息产品。标识中央的 数字为环保使用期限的年数。只要您遵守该产品相关的安全及使用注意事项，在自制造日起算的年限内，不会 产生对环境污染或人体及财产的影响。上述标识粘贴在机器背面。 • 有毒有害物质或元素的名称及含量 部件名称 有毒有害物质或元素 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 （Pb） （Hg） （Cd） （Cr（VI）） （PBB） （PBDE） 印刷电路板 × ○ ○ ○ ○ ○ 机箱 ○ ○ ○ ○ ○ ○ 液晶显示器 × ○ ○ ○ ○ ○ 其他 × ○ ○ ○ ○ ○ ○ ：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 规定的限量要求以下。 × ：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 规定的限量要求。 ( 企业可在此处 , 根据实际情況对上表中打“×”的技术原因进行进一步说明 ) Appendix
1st Edition-April, 2013 Copyright © 2013 EIZO Corporation All rights reserved. 03V24481A1 (U.
