ENGLISH
SAFETY SYMBOLS This manual uses the safety symbols below. They denote critical information. Please read them carefully. WARNING Failure to abide by the information in a WARNING may result in serious injury and can be life threatening. CAUTION Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage. Indicates a prohibited action. Indicates to ground for safety. Copyright© 2000 by EIZO NANAO CORPORATION. All rights reserved.
TABLE OF CONTENTS PRECAUTIONS .............................................................................. 4 1. INTRODUCTION .......................................................................... 10 2. ENGLISH 1-1. Features ..................................................................................................... 10 1-2. Package Contents ...................................................................................... 10 1-3. Controls & Connectors ..................................
PRECAUTIONS IMPORTANT! ´ This product has been adjusted specifically for use in the region to which it was originally shipped. If operated outside the region to which it was originally shipped, the product may not perform as stated in the specifications. ´ To ensure personal safety and proper maintenance. Please read this section and the caution statements on the monitor (refer to the figure below). [Location of the Caution Statements] Risk of electric shock. Do not open. Risque de choc electrique.
WARNING ENGLISH ´ Keep small objects away from the monitor. Small objects may accidentally fall through the ventilation slots into the cabinet, leading to fire, shock, or equipment damage. ´ Keep liquids away from the monitor. Spillage into the cabinet may result in fire, electric shock, or equipment damage. If an object or liquid falls/spills into the cabinet, unplug the monitor immediately. Have the monitor checked by a qualified service engineer before using it again.
WARNING ´ To disconnect the power cord, grasp the plug firmly and pull. Never tug on the cord, doing so may cause damage and could result in fire or electric shock. ´ The equipment must be connected to a grounded main outlet. ´ Use the correct voltage. * The monitor is designed for use with a specific voltage only. Connection to a different voltage may cause fire, electric shock, or other damage. * Do not overload your power circuit, as this may result in fire or electric shock.
WARNING ENGLISH ´ Install the monitor securely when attaching to an arm stand. When attaching an arm stand, please refer to the user’s manual of the arm stand and install the monitor securely with the enclosed screws. Not doing so may cause the monitor to come unattached, which may result in injury or equipment damage. When the monitor is dropped, please ask your dealer for advice. Do not continue using a damaged monitor. Using a damaged monitor may result in fire or electric shock.
CAUTION ´ Do not block the ventilation slots on the cabinet. * Do not place books or any other papers on the ventilation slots. * Do not install the monitor in a closed space. * Do not use the monitor lengthwise or upside down. Using the monitor in this way blocks the ventilation slots and prevents proper airflow, leading to fire or other damage. • Do not use the LCD monitor outdoors or indide a car. This LCD monitor has been made specifically for indoor use as a desktop monitor.
Suggestions for Maximizing Comfort ENGLISH ´ To lessen the chance of possible injury and to increase your comfort and productivity while you operate the unit, we suggest the following: * Avoid less favorable body positioning. Sit back on the chair with your back straight. * Adjust the height of the chair so that the both soles touch the floor. * Adjust the height of your chair, monitor, or keyboard so that you can keep your wrists straight while typing. * Set the terminal slightly below eye level.
1. INTRODUCTION Thank you very much for choosing an EIZO Color Monitor. 1-1. Features • • • • • DVI p.27) digital input (TMDS p.27)) compliant. 1024 x 768 resolution p.27) and automatic full screen support for lower resolutions. Smoothing function incorporated for the adjustment of an enlarged image. DVI DMPM p.27) power saving compliant, less than 3 W in power saving mode. Two kinds of brightness adjustment accessible through the brightness selection button on he front panel. 1-2.
1-3.
2. CABLE CONNECTION 2-1. Before Connecting Following 4 resolutions p.27) with frequency can be displayed on this model. The lower display modes like 640 x 480 or 720 x 400 mode, automatically enlarge to the maximum display mode (1024 x 768). In this case, some lines of the characters may become fuzzy. Use “Smoothing” function to make the lines clear (see page 18). Resolution Frequency Remarks 640 x 480 60 Hz VGA 720 x 400 70 Hz VGA Text 800 x 600 60 Hz VESA 1024 x 768 60 Hz VESA 2-2.
WARNING ENGLISH • Use the enclosed power cord. If using the power cord other than the enclosed one, follow these guidelines. [USA and Canada] Use a UL LISTED/CSA LABELED or CERTIFIED power cord set meeting the following specifications: * Rating: min. 125 V, 10 A * Length: max.2.0 m * Type: SVT * Plug type: NEMA 5-15P, Parallel blade, Grounding type, 125 V, 10 A [Europe] Use a proper European standard approved power cord meeting the following specifications: * Rating: min. 250 V, 10 A *Length: max.2.
3. ScreenManager 3-1. How to use the ScreenManager As shown on the display, the ScreenManager is used to adjust the LCD monitor. ScreenManager consists of main menus and sub menus. Adjustments are made using the Enter and Control buttons (up, down, right and left) located on the front panel. < Main menu> Enter Button Control Buttons 1. Entering the ScreenManager Push the Enter button once to display the main menu of the ScreenManager. 2. Making Adjustments and Settings (1) (2) (3) 3.
3-2. ScreenManager Adjustments and Settings. The following table shows all the ScreenManager’s adjustment and setting menus. PowerManager Others Information Language Sub menu Position Resolution Smoothing Brightness DVI DMPM Off timer Menu Position Reference 4-1. Screen Adjustment (p.17) 4-2. Power-save Setup (p.19) Set the monitor’s timer to on or off (p.16). Adjust the ScreenManager’s menu position. Reset Return to the factory default settings. (p.
Off Timer The off timer function causes the monitor to automatically enter a power off state after a predetermined amount of time has lapsed. This function was created to reduce afterimage p.27) characteristics that are particular to LCD monitors when the monitor screen is left on for a long period without use. [Procedure] (1) Select “Off Timer” in the ScreenManager “Others” menu. (2) Select “Enable” and press the right and left buttons to adjust the “On Period” (1 to 23 hours).
4. ADJUSTMENT 4-1. Screen Adjustment • Allow the monitor to warm up for at least 20 minutes before making any adjustments. 1. The screen position is incorrect. Æ “Position” adjustment The correct displayed position of the monitor is decided because the number and the position of the pixels are fixed. The “Position” adjustment moves the image to the correct position.
3. Smooth blurred texts. Æ Adjust the “ Smoothing” Select a suitable level from 1~5 (soft ~ sharp). Select “Smoothing” and adjust by using the right and left buttons. 4. Set the Brightness of the screen Æ Adjust the “Brightness” This controls the brightness of the screen. The brightness of the entire screen is controlled by changing the brightness of the backlight. [Brightness 1 & Brightness 2] The L351 has two memories for the preferable brightness setting (Brightness 1 & Brightness 2).
4-2. Power-save Setup This monitor complies with the DVI DMPM p.27). ENGLISH [Procedure] (1) Set the PC’s power saving settings. (2) Select “DVI DMPM” in the “PowerManager” menu. [Power saving system] PC Monitor LED Power consumption On Operation Green 35 W Power saving Power saving Yellow Less than 3 W Off mode Power saving Flashing yellow (2 times for each) Less than 1 W Operate the mouse or keyboard to return to a normal screen from the Power save mode of the PC.
5. ATTACHING AN ARM STAND The L351 can be used with an arm stand by removing the tilt stand and attaching the arm stand to the terminal. NOTE ´ Use an arm stand that satisfies the followings. • When using the L351 with an arm stand, the arm stand must be VESA approved : * Use an arm stand with a 75 mm x 75 mm hole spacing on the arm mounting pad. * Use an arm stand that is able to support anobject weighing 8.0 kg. ´ TÜV/GS approved arm stand.
3. Attach an arm stand to the L351 securely. ENGLISH WARNING ´ Install the unit securely when attaching to an arm stand. When attaching an arm stand, please refer to the user’s manual of the arm stand and install the unit securely with the enclosed screws. Not doing so may cause the unit to come unattached, which may result in injury or equipment damage. When the unit is dropped, please ask your dealer for advice. Do not continue using a damaged unit.
6. TROUBLESHOOTING If a problem persists even after applying the suggested remedies, contact an EIZO dealer. Problems 1. No picture • Indicator status: Off • Indicator status: Green • Indicator status : Yellow : Flashing Yellow Points to check with possible solutions Check that the power cord is correctly connected. If the problem persists, turn off the monitor power for a few minutes, then turn it back on and try again. Check the “Brightness” settings. Minimum settings will cause screen to be blank.
Points to check with possible solutions 3. Display position is incorrect. Adjust the image position using the “Position”. (p.17) If the problem persists, use the graphics board’s utility software to change the display position if available. 4. Screen image is smaller or larger than the actual screen images. Adjust the resolution using the “Resolution”. (p.17) 5. Letters and lines appear blurred. Adjust the blurred lines using “Smoothing”. (p.18) 6. Afterimages appear.
7. CLEANING Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime. WARNING ´ Keep liquids away from the unit. Spillage into the cabinet may result in fire, electric shock, or equipment damage. If an object or liquid falls/spills into the cabinet, unplug the monitor immediately. Have the unit checked by a qualified service engineer before using it again. CAUTION ´ Unplug the unit before cleaning it.
8. SPECIFICATIONS LCD Panel Dot Clock (Max.
Dimensions 384 (15.1) 69 (2.7) 37.2 (1.5) 23 (0.9) 39 (1.5) 306 (12.0) 325 (12.8) 230 (9.1) 25 3 386.2 (15.2) 57.8 (2.3) 170 (6.7) 36.8 (1.4) 167 (6.6) 171.4 (6.7) 5 (0.2) FRONT VIEW TOP VIEW SIDE VIEW Pin Assignment * DVI-D connector 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Pin No. Signal Pin No. Signal 1 TMDS Data2- 9 TMDS Data1- Pin No.
9. GLOSSARY Afterimage The Afterimage is particular to LCD monitors when the monitor screen is left on for a long period without use. The “Afterimage” can be removed gradually by changing the displayed image. (Digital Visual Interface) A digital flat panel interface. DVI can transmit digital data from the PC directly without loss with the signal transition method “TMDS”. There are two kinds of DVI connectors. One is DVI-D connector for digital signal input only.
10.
[Applicable to gray (standard color version only).] Congratulations! You have just purchased a TCO’99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
[Applicable to gray (standard color version only).] Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs.
For U.S.A, Canada, etc. (rated 100-120 Vac) Only FCC Declaration of Conformity We, the Responsible Party EIZO NANAO TECHNOLOGIES INC. 5710 Warland Drive, Cypress, CA 90630 Phone: (562) 431-5011 declare that the product Trade name: EIZO Model: FlexScan L351 is in conformity with Part 15 of the FCC Rules.
Hinweis zur Ergonomie : Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach EK1/59-98, EK1/6098 mit dem Videosignal, 1024 Punkte x 768 Zeilen, Digital Eingang und mindestens 60,0 Hz Bildwiederholfrequenz, non interlaced. Weiterhin wird aus ergonomischen Gründen empfohlen, die Grundfarbe Blau nicht auf dunklem Untergrund zu verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast.
