Notice for this monitor CONTENTS Chapter 1 Features and Overview 1-1 Features 1-2 Names of Switches 1-3 Operation Switch Usage 1-4 Functions of Remote Control Buttons 1-5 Functions and Basic Operation Chapter 2 Settings and Adjustment 2-1 Input Signal Switching 2-2 Screen Adjustment 2-3 Color Adjustment 2-4 Sound Adjustment 2-5 Auto Screen Size Changing Important 2-6 Screen Ratio Changing 2-7 Monitor Power-saving Mode Setting Please read PRECAUTIONS, this User’s Manual and Setup Manual (separate volume)
As an ENERGY STAR® Partner, EIZO NANAO CORPORATION has determined that this product meets the ENERGY STAR guidelines for energy efficiency. Using the special functions, such as screen size change (ex. changing the horizontal and vertical ratio of images input) for commercial purposes or for the purpose of showing in public may violate copyright laws. Product specification may vary with sales areas. Confirm the specification in the manual written in language of the region of purchase.
Notice for this monitor This product is suited to creating documents, viewing multimedia content, and other general purposes. This product has been adjusted specifically for use in the region to which it was originally shipped. If the product is used outside the region, it may not operate as specified in the specifications. This product may not be covered by warranty for uses other than those described in this manual.
Cleaning Attention • Never use any solvents or chemicals, such as thinner, benzene, wax, alcohol, and abrasive cleaner, which may damage the cabinet or LCD panel. NOTE • Optional ScreenCleaner is recommended for cleaning the panel surface. [LCD Panel] • Clean the LCD panel with a soft cloth such as cotton cloth or lens cleaning paper. • Remove persistent stains gently with a cloth dampened with a little water, and then clean the LCD panel again with a dry cloth for better finishing.
CONTENTS Notice for this monitor............................................... 3 2-8 Power Indicator/EIZO Logo Display Setting........ 26 ● To turn off the power indicator while a screen is Cleaning.................................................................. 4 displayed [Power Indicator]............................... 26 To use the monitor comfortably............................ 4 ● To set EIZO logo display/no EIZO logo display when the monitor turns on [EIZO Logo Appearing CONTENTS...........
Chapter 1 Features and Overview Thank you very much for choosing an EIZO color LCD monitor.
Connecting to peripheral devices equipment PC Speakers (with built-in amplifier) DVI connector D-Sub mini 15-pin connector Allows you to enjoy sound from a connected PC or AV equipment, etc. NOTE Enables you to use as a monitor by connecting to a Windows PC or a Macintosh. • Enables you to adjust the speaker volume connected to the monitor using the volume adjustment function of the monitor. • Enables you to enjoy sound by connecting a headphone to the headphone jack.
1-2 Names of Switches Setting menu (ScreenManager® *) Switch 1 1. 2. 3. 4. 5. 6. 7. 2 3 4 Remote control detector Sensor (Detects the environmental brightness.) ) Input Signal Selection switch ( Slide bar Menu switch ( ) Power switch ( ) Power indicator Indicator status Operation status Blue The screen is displayed Orange Power saving Off * 5 6 7 Power off ® ScreenManager is an EIZO’s nickname of the Setting menu.
1-3 Operation Switch Usage ■ Turning the power On/Off Power On: Touch any of the keys to turn on the monitor. Power Off: Touch . ■ Switching the Input Signal Tap NOTE Each time you tap the switch, the input signal switches to the other. . ■ Displaying/Quitting a menu Setting menu • There are three methods of operation: Touch . - Touching the switch Shortcut menu Touch the slide bar.
1-4 Functions of Remote Control Buttons (2) (1) (3) (5) (4) (6) (7) (9) (8) (10) (11) (12) 1 2 3 4 5 Button POWER OFF TIMER COLOR MODE SCREEN SIZE GAME SIZE THRU 6 USB 7 t / u / ENTER 8 9 10 11 MENU VOLUME MUTE INPUT SELECT PC HDMI 12 PinP ON/OFF FULL SOUND POSITION TEMP OFF TRANSLUCENT 10 Function Turns the power on or off Sets the time until the monitor power-off Changes the color mode Changes the screen size Use when displaying the game images (for HDMI input signal) Changes the screen
1-5 Functions and Basic Operation To adjust the screen, color and volume (Only for analog input signal from PC: PC 2 Input) 1 Screen Adjustment Page 15 Screen menu Setting menu (As for the menu operation, refer to page 13.
To make useful settings/adjustments Resumption of Default Settings Page 28 ● To reset all settings [Reset] Setting menu (As for the menu operation, refer to page 13.
To make useful settings/adjustments (Continued) The following settings and adjustments are available with the remote control. For the details on the function, refer to “Remote Control Guide”.
Chapter 2 Settings and Adjustment 2-1 Input Signal Switching ● To switch the input signal for the desired image sent from the equipment [Input Selection] [Procedure] of the operation switch. (1) Tap Each time you tap the switch, the input signal switches as below. PC1 → PC2 → HDMI1 → HDMI2 → PC1..... NOTE • The input signal can be switched with the remote control. (Refer to “Remote Control Guide”.) • Touching the switch during PinP display switches the input signal of the Sub-Window.
2-2 Screen Adjustment (Only for analog input signal from a PC) The monitor screen adjustment is used to suppress flickering of the screen or adjust screen position and screen size correctly according to the PC to be used. To use the monitor comfortably, adjust the screen when the monitor is set up for the first time or when the settings of the PC in use are updated. No adjustment is required when the image appears correctly.
3 Perform the auto screen adjustment again with the analog screen adjustment pattern displayed. ● T o adjust flickering, screen position, and screen size automatically [Auto Screen Adjust] (1) Display Pattern 1 in full screen on the monitor using the “Screen Adjustment Utility” or the screen adjustment pattern files. (2) Choose the icon in the Setting menu and tap the slide bar. The menu appears. (3) Choose the icon in the menu and tap the slide bar.
● To remove flickering or blurring [Phase] (1) Choose the icon in the menu and tap the slide bar. The menu appears. Attention • The flickering or blurring may not be eliminated perfectly depending on your PC or graphics board. (2) Trace the slide bar left and right to remove the flickering or blurring and tap the slide bar. The adjustment is completed. ● To correct screen position [Hor.Position/Ver.
5 Adjust the color gradation. ● To adjust color gradation automatically [Auto Range Adjust] Every color gradation (0 to 255) can be displayed by adjusting the signal output level. (1) Display Pattern 2 in full screen on the monitor using the “Screen Adjustment Utility” or the screen adjustment pattern files. (2) Choose the icon in the menu and tap the slide bar. “Your current setting will be lost, if you perform “Auto Range Adjust”. Do you continue?” appears on the screen.
2-3 Color Adjustment Simple Adjustment ● To select the color mode [Color Mode] NOTE • The color mode can be changed with the remote control. (Refer to “Remote Control Guide”.) • The adjustment status of the Color Mode may be changed. (Refer to “Advanced Adjustment” on page 20.) Changing the color mode enables you to set the monitor to the appropriate display mode. (PC Input Signal) An appropriate display mode is selectable out of six modes.
Advanced Adjustment ● To adjust/set Color Mode Attention Independent adjustments/settings and saving of the Color adjustment are available for each mode.
● Adjustment items Menu NOTE Description • The values shown in the “%” are available only as reference. Adjustment range Brightness To adjust the full screen brightness as desired 0 to 100% Black Level To adjust the black level as 0 to 100% desired NOTE • RGB (Red, Green, Blue) is adjusted respectively for PC input signal, and RGB is adjusted together for HDMI input signal.
[Procedure] (1) Choose the icon in the Setting menu and tap the slide bar. (2) Choose the icon in the menu and tap the slide bar. (3) Select the desired color mode in the menu and tap the slide bar. (4) Select the desired function to adjust/set in the menu and tap the slide bar. NOTE • The menu and the menu can be displayed from the shortcut menu. (See page 9) The selected function menu appears.
2-4 Sound Adjustment ● To adjust [Treble/Bass/Balance/Sound Level]. Menu Description Adjustment range Treble To adjust the sound strengths/weaknesses in the -15 to 15 high sound area Bass To adjust the sound strengths/weaknesses in the -15 to 15 low sound area Balance Sound Level NOTE To adjust the volume balance -32 to 32 on left and right sides To adjust the input sound level -3 to 3 [Procedure] (1) Choose the icon in the Setting menu and tap the slide bar.
2-5 Auto Screen Size Changing (HDMI input signal only) ● To change the screen size automatically according to the aspect information of the input signal [Auto Screen Size] The screen size can be changed automatically according to the aspect information of the input signal from AV equipment. [Procedure] (1) Choose the icon in the Setting menu and tap the slide bar. (2) Choose the icon in the menu and tap the slide bar.
Input signal:Aspect ratio (Format) Screen Ratio 4:3 (480i/480p/ 576i/576p) 16:9 Letterbox (480i/480p/ 576i/576p) (480i/480p/ 576i/576p) (1080i/720p/1080p) Standard Full Image Full Screen 2-7 Attention Monitor Power-saving Mode Setting ● To set the resume conditions from the power-saving mode [Signal Detection] This function sets the power-saving mode condition when no input signal is detected on the current selected input signal and the resume conditions from the power-saving mode.
2-8 Power Indicator/EIZO Logo Display Setting ● To turn off the power indicator while a screen is displayed [Power Indicator] This function enables you to turn off the Power indicator (blue) while a screen is displayed. NOTE • The Power indicator lights up at power on with the default setting. [Procedure] (1) Choose the icon in the Setting menu and tap the slide bar. (2) Choose the icon in the menu and tap the slide bar.
[Procedure] (1) Choose the icon in the Setting menu and tap the slide bar. (2) Choose the icon in the menu and tap the slide bar. The menu appears. (3) Trace the slide bar left and right to select either “On” or “Off” and tap the slide bar. The beep setting is completed. 2-10 Information Checking ● To check settings, usage time, etc. [Information] NOTE • The usage time is not always “0” when you purchase the monitor due to factory inspection.
2-12 Locking Switches ● To lock the available functions [Operation Lock] This function enables you to lock the switches to retain the setting/adjustment set once and restrict the available functions. [Locking] (1) Touch (2) Touch to turn off the monitor. for approx. three seconds. NOTE • The following operations are available in the locked status. - Power ON/OFF by touching . - Power ON by touching , or the slide bar.
Chapter 3 Troubleshooting If a problem still remains after applying the suggested remedies, contact your local dealer. • • • • No picture problems→See No. 1 and 2 in (PC Input Signal), No. 1 and 2 in (HDMI Input Signal) Imaging problems→See No. 1 - 6 in (Common), No. 3 - 7 in (PC Input Signal), No.3 in (HDMI Input Signal) Other problems→See No. 7 - 12 in (Common), No. 8 in (PC Input Signal), No. 4 and 5 in (HDMI Input Signal) USB problems→See No.
(PC Input Signal) Problems 1. No Picture • Power indicator does not light up. Possible cause and remedy • Check whether the power cord is correctly connected. • Press on the remote control or touch of the operation switch. • Power indicator lights in orange. • Switch the input signal with [INPUT SELECT] ( ) on the remote control or of the operation switch. • Press a key on the keyboard or click the mouse. • Turn on the PC. • Power indicator lights in blue.
Problems Possible cause and remedy 7. Noise appears on the screen. • When entering the signals of analog input, change the setting in from the menu. The symptom may not be improved depending on the input signal used. It is recommended that you switch the analog input signal to digital. • When receiving HDCP signals, the normal images may not be displayed immediately. 8. No sound/Volume control is not available.
(HDMI Input Signal) Problems 1. No Picture • Power indicator does not light up. Possible cause and remedy • Check whether the power cord is correctly connected. • Press on the remote control or touch of the operation switch. • Power indicator lights in orange. • Switch the input signal with [INPUT SELECT] ( ) on the remote control or of the operation switch. • Turn on the AV equipment. • Power indicator lights in blue. • Check whether the AV equipment is properly connected to the monitor.
● Messages List The meanings of the main messages appearing on the screen are described below. Messages Description “Your current setting will be lost, if you perform “Auto Screen Adjust”. Do you continue?” Appears when performing [Auto Screen Adjust]. “Your current setting will be lost, if you perform “Auto Range Adjust”. Do you continue?” Appears when performing [Auto Range Adjust]. “Your current color data will be lost.” Appears when performing in the menu.
Chapter 4 Reference 4-1 Attaching an Arm The stand can be removed and replaced with an arm (or another stand) to be attached to the monitor. Use an arm or stand of EIZO option. [Attaching] 1 2 Lay the LCD monitor on a soft cloth spread over on a stable surface with the panel surface facing down. Remove the stand. (Prepare a screwdriver.) Unscrew the four screws securing the unit and the stand with the screwdriver. 3 Attach the monitor to the arm or stand.
4-2 Specifications Panel LCD Panel 24.1-inch (610 mm) TFT color LCD with anti-glare hard coating Viewing angle: Vertical 178°, Horizontal 178° (CR: 10 or more) Dot Pitch 0.270mm Resolution 1920 dots × 1200 lines Max. Display Color Approx. 16.77 million colors: Applicable to 8 bit (1048.77 million colors) Display Area (H × V) 518.4mm × 324.0mm PC Input Signal Digital Input Signal (PC 1) Input Signal Connector DVI-D × 1 Horizontal Scan Frequency 31.
Dimensions Weight Environmental Conditions Main unit 566mm (22.3”) (W) × 363.5 - 480mm (14.3 - 18.9”) (H) × 230mm (9.1”) (D) without Stand 566mm (22.3”) (W) × 396mm (15.6”) (H) × 92.3mm (3.6”) (D) Main unit approx. 10.3kg (22.7 lbs) without Stand approx. 7.9kg (17.4 lbs) Temperature Operating temperature : 0°C - 35°C Storage temperature : -20°C - 60°C Humidity Operating humidity: 30% - 80% R.H. (no condensation) Storage humidity: 30% - 80% R.H.
Setting menu list Item Screen Color PC 1 PC 2 HDMI 1 HDMI 2 PinP Auto Screen Adjust − √ − − √* Auto Range Adjust − √ − − √* Clock − √ − − √* Phase − √ − − √* Hor.Position − √ − − √* Ver.
Main default settings (factory settings) PC 1/PC 2 Color Mode Volume HDMI 1/HDMI 2 Custom Speaker 30 Headphone 10 PinP Off Language English BrightRegulator Standard Signal Detection Current Input Signal Power Indicator On Beep On Auto Screen Size − Enable Screen Ratio − [480i/480p/576i/576p signal] Standard [1080i/720p/1080p signal] Full Image Color Space − Auto USB PC 1 Screen Size Full Screen Off Timer [480i/480p/576i/576p signal] 4:3 [1080i/720p/1080p signal] 16 : 9 Disabl
4-3 Glossary Clock The analog input monitor needs to reproduce a clock of the same frequency as the dot clock of the graphics system in use, when the analog input signal is converted to a digital signal for image display. This is called clock adjustment. If the clock pulse is not set correctly, some vertical bars appear on the screen. Color Space Color space is a method to specify and express the color. There are YUV and RGB, etc.
HDMI (High-Definition Multimedia Interface) HDMI is a digital interface standard, developed for consumer electrical appliance or AV equipment. This standard is issued on the basis of the DVI standard which is one of an interface specification for the connection between a PC and a monitor. The projected image, sound and control signal without compressed enable to be sent/received with one cable. Only the input signal of this product corresponds to the standard.
4-4 Preset Timing The following table shows factory preset video timing (for analog signal only). Mode Dot clock NEC PC-9821 640×400@70Hz 25.2 MHz VGA 640×480@60Hz 25.2 MHz VGA 720×400@70Hz 28.3 MHz Macintosh 640×480@67Hz Macintosh 832×624@75Hz Macintosh 1152×870@75Hz Macintosh 1280×960@75Hz 30.2 MHz 57.3 MHz 100.0 MHz 126.2 MHz VESA 640×480@73Hz 31.5 MHz VESA 640×480@75Hz 31.5 MHz VESA 720×480@60Hz 28.3 MHz VESA 800×600@56Hz 36.0 MHz VESA 800×600@60Hz 40.0 MHz VESA 800×600@72Hz 50.
VESA CVT RB 1680×1050 VESA CVT RB 1920×1200 119.0 MHz 154.0 MHz Horizontal Vertical Horizontal Vertical 64.67 59.88 74.04 59.95 Positive Negative Positive Negative (The signals specified below are also applicable for the use of some AV equipments such as Microsoft Xbox 360.) Mode Dot clock 720@50Hz 1280×720p 74.3 MHz 720@60Hz 1280×720p 74.3 MHz 1080@50Hz 1920×1080p 148.5 MHz 1080@60Hz 1920×1080p 148.
Applicable to Black cabinet only. Congratulations! The display you have just purchased carries the TCO’03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also minimizes the Impact on our natural environment.
For U.S.A. , Canada, etc. (rated 100-120 Vac) Only FCC Declaration of Conformity We, the Responsible Party EIZO NANAO TECHNOLOGIES INC. 5710 Warland Drive, Cypress, CA 90630 Phone: (562) 431-5011 declare that the product Trade name: EIZO Model: FlexScan HD2442W is in conformity with Part 15 of the FCC Rules.
Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor Dieser Monitor ist für Bildschirmarbeitsplätze vorgesehen. Wenn nicht der zum Standardzubehör gehörige Schwenkarm verwendet wird, muss statt dessen ein geeigneter anderer Schwenkarm installiert werden.
EIZO NANAO CORPORATION 153 Shimokashiwano, Hakusan, Ishikawa 924-8566 Japan Phone: +81 76 277 6792 Fax:+81 76 277 6793 EIZO NANAO TECHNOLOGIES INC. 5710 Warland Drive, Cypress, CA 90630, U.S.A. Phone: +1 562 431 5011 Fax: +1 562 431 4811 EIZO EUROPE AB Lovangsvagen 14 194 61, Upplands Väsby, Sweden Phone: +46 8 594 105 00 Fax: +46 8 590 91 575 EIZO NANAO AG Moosacherstrasse 6, Au CH - 8820 Wädenswil, Switzerland Phone: +41-0-44 782 24 40 Fax: +41-0-44 782 24 50 http://www.eizo.
