Important Please read PRECAUTIONS, this User’s Manual and Setup Guide (separate volume) carefully to familiarize yourself with safe and effective usage. • Please read the Setup Guide (separate volume) • The latest User’s Manual is available for download from our site: http://www.eizo.
[Location of Caution Statement] Ex. Height adjustable stand As an ENERGY STAR® Partner, EIZO NANAO CORPORATION has determined that this product meets the ENERGY STAR guidelines for energy efficiency. Product specification may vary with sales areas. Confirm the specification in the manual written in language of the region of purchase. Copyright© 2009 EIZO NANAO CORPORATION All rights reserved.
Notice for this monitor This product is suited to creating documents, viewing multimedia content, and other general purposes. This product has been adjusted specifically for use in the region to which it was originally shipped. If the product is used outside the region, it may not operate as specified in the specifications. This product may not be covered by warranty for uses other than those described in this manual.
Cleaning Attention • Never use any solvents or chemicals, such as thinner, benzene, wax, alcohol, and abrasive cleaner, which may damage the cabinet or LCD panel. NOTE • Optional ScreenCleaner is recommended for cleaning the panel surface. [LCD Panel] • Clean the LCD panel with a soft cloth such as cotton cloth or lens cleaning paper. • Remove persistent stains gently with a cloth dampened with a little water, and then clean the LCD panel again with a dry cloth for better finishing.
CONTENTS ● To adjust brightness of non-display area Notice for this monitor............................................... 3 [Border Intensity]............................................... 23 CONTENTS.............................................................. 5 2-11 Setting Adjustment Menu Display................. 24 ● To update menu settings [Menu Size/ Chapter 1 Features and Overview...................... 7 Menu Position/Menu Off Timer/Translucent]..... 24 1-1 Features........................
CONTENTS Chapter 5 Reference.......................................... 34 5-1 Attaching an Arm............................................ 34 5-2 Folding the EZ-UP stand................................ 35 5-3 Specifications................................................. 36 5-4 Glossary.......................................................... 45 5-5 Preset Timing.................................................. 47 TCO’03 . ..........................................................
Chapter 1 Features and Overview Thank you very much for choosing an EIZO color LCD monitor. 1-1 Features • 22” wide format LCD Applicable to WSXGA+ (1680×1050) (S2232W)/ 22” wide format LCD Applicable to WUXGA (1920×1200) (S2242W)/ 24” wide format LCD Applicable to WUXGA (1920×1200) (S2432W) • Built-in speakers and headphone jack 1-2 “Controls and Functions” (page 8) • Power saving function Suppressing the power consumption* reduces the carbon dioxide emissions.
1-2 Controls and Functions Ex.
1-3 Compatible Resolutions/Frequencies The monitor supports the following resolutions.
1-4 Functions and Basic Operation To adjust the screen and color Main menu (Refer to page 12 for operation) Analog input only [At analog signal input] 1 [At digital signal input] ● To adjust flickering and position [Screen]………………………………… see page 14 ● To adjust color gradation automatically [Range]………………………………… see page 16 2 Screen Adjustment (Automatic Adjustment) Screen Adjustment (Advanced Adjustment) [At analog signal input] Page 14 Page 15 [At digital signal input] • The Adjustment menu a
To make useful settings/adjustments Adjustment menu (Refer to page 12 for operation) [At analog signal input] Power-save Settings ● Setting On/Off for Power Saving mode [Power Save] … ………………………see page 21 ● Turning off the monitor automatically [Off Timer] … …………………………see page 22 ● Displaying the level of power saving by EcoView Index [EcoView Index]… ……………see page 22 [At digital signal input] Other Settings Information Page 25 ● Displaying Monitor Infomation [Information] Language Page 26 ● To c
Basic operation of Adjustment menu [Displaying Adjustment menu and selecting function] . The Main menu appears. (1) Press (2) Select a function with / / / , and press . The Sub menu appears. (3) Select a function with / / / , and press . The adjustment/setting menu appears. (4) Adjust the selected item with / / / , and press . The setting is saved. [Exiting Adjustment menu] (1) Choose from the Sub menu and press (2) Choose from the Main menu and press . The Main menu appears. .
Chapter 2 Settings and Adjustments 2-1 Utility Disk An “EIZO LCD Utility Disk” (CD-ROM) is supplied with the monitor. The following table shows the disk contents and the overview of the software programs. ● Disk contents and software overview The disk includes software programs for adjustment, and User's Manual. Refer to “Readme.txt” or the “read me” file on the disk for software startup procedures or file access procedures. Item Overview OS A “Readme.
2-2 Screen Adjustment Digital Input When digital signals are input, images are displayed correctly based on the preset data of the monitor, but if characters and/or lines appear blurred, go to step 6 “To modify blurred characters/lines [Smoothing]”. When performing more advanced adjustment, see “2-3 Color Adjustment” (page 17) and subsequent pages.
3 Perform the auto adjustment again with the analog screen adjustment pattern displayed. ● To adjust flickering, screen position, and screen size automatically [Screen] (1) Display Pattern 1 in full screen on the monitor using the “Screen Adjustment Utility” or the screen adjustment pattern files. (2) Choose from the menu, and press . The menu appears. (3) Choose with or .
● To correct screen position [Position] (1) Choose from the menu, and press NOTE . The menu appears. (2) Adjust the position with / / / to display the image properly in the display area of the monitor, and press The adjustment is completed. 5 • Since the number of pixels and the pixel positions are fixed on the LCD monitor, only one position is provided to display images correctly. The position adjustment is made to shift an image to the correct position.
2-3 Color Adjustment ● To select the display mode (FineContrast mode) FineContrast allows you to select the best display mode easily according to the monitor’s application. FineContrast mode Mode Purpose Custom Available to change all setting values. sRGB Suitable for color matching with sRGB compatible peripherals. Text Suitable for displaying texts for word processing or spreadsheets. Picture Suitable for displaying images such as photos or picture images.
● To perform advanced adjustments Attention Independent setting and saving of color adjustment are available for each FineContrast mode. ● Adjustment items in each mode According to the FineContrast mode selected, the adjustable function differs.
● To adjust the color temperature [Temperature] NOTE The color temperature can be adjusted. The color temperature is normally used to express the hue of “White” and/or “Black” by a numerical value. The value is expressed in degrees “K” (Kelvin). In the same way as the flame temperature, the image on the monitor is displayed reddish if the color temperature is low and is bluish if the color temperature is high. The gain preset values are set for each color temperature setting value.
● To adjust the hue [Hue] Attention This function allows you to adjust the hue. If you set the hue to a high value, the image turns greenish. If low, the image turns purplish. Adjustable range: -32 to 32 (1) Choose from the Adjustment menu, and press (2) Choose from the menu, and press . . The adjustment menu appears. (3) Adjust the hue with or , and press . • This function does not enable to display every color gradation.
2-6 NOTE Setting On/Off for the automatic brightness adjustment function [Auto EcoView] • Be careful not to block the sensor on the lower side of the monitor when using the Auto EcoView function. The sensor on the front side of the monitor detects the environmental brightness to adjust the screen brightness automatically and comfortably by using the Auto EcoView function. (1) Press . The setting menu appears. (2) The On/Off setting is toggled by pressing 2-7 .
2-8 Turning off the monitor automatically [Off Timer] This function allows you to switch the setting to turn off the monitor automatically after a specified time has passed at the power saving mode. Adjustable range: Disable, Enable (0, 1, 2, 3, 5, 10, 15, 20, 25, 30, 45 min, 1-5h) (1) Choose from the Adjustment menu, and press . (2) Choose from the menu, and press . The setting menu appears. (3) Select “Enable” or “Disable” with or .
2-10 Screen Size Selection ● To change screen size [Screen Size] The image with the resolution other than the recommended resolution is displayed in full screen automatically. You can change the screen size by using from menu. Menu Function Full Screen (default setting) Displays an image in full screen. Images are distorted in some cases because the vertical rate is not equal to the horizontal rate. Enlarged Displays an image in full screen.
2-11 Setting Adjustment Menu Display ● To update menu settings [Menu Size/Menu Position/Menu Off Timer/Translucent] Menu Size Change the Adjustment menu size using the following procedure. (1) Choose from the Adjustment menu, and press . (2) Choose
NOTE 2-12 Setting Orientation ● To set the orientation of the Adjustment menu [Orientation] This function allows you to change the orientation of the Adjustment menu when using the monitor screen in vertical display position. (1) Choose from the Adjustment menu, and press (2) Choose from the Others menu, and press . . The menu appears. (3) Select “Landscape” or “Portrait” with or , and press .
NOTE 2-15 Enabling/Disabling DDC/CI communication • You can check the DDC/CI setting in the menu. This function allows you to enable/disable the DDC/CI communication. (1) Press to turn off the monitor. (2) Press holding down to turn on the monitor. The Enable/Disable setting is toggled by performing the operation in step 2. 2-16 Setting Power Indicator ON/OFF [Power Indicator] This function allows you to set the power indicator (blue) ON/OFF in the monitor ON condition.
2-19 Resuming the Default Setting [Reset] Attention There are two types of Reset. One is to reset the color adjustment only to the default settings, and the other is to reset all the settings to the default settings. • After resetting, you cannot undo the operation. ● To reset color adjustment values Only the adjustment values in the current FineContrast mode will revert to the default settings (factory settings). (1) Choose from the Adjustment menu, and press .
Chapter 3 Connecting Cables 3-1 Connecting Two PCs to the Monitor Two PCs can be connected to the monitor through the DVI-D and the D-Sub mini 15 pin connector on the back of the monitor. Connection examples DVI-D connector Digital To PC 1 D-Sub mini 15-pin Connector Analog To PC 2 D-Sub mini 15-pin Connector DVI-D connector Signal cable (supplied FD-C39) Signal cable (supplied MD-C87) ● To switch the input signal The input signal switches each time is pressed.
● To set input signal selection [Input Signal] NOTE The monitor recognizes the connector through which PC signals are input. When either PC is turned off or enters the power-saving mode, the monitor automatically displays signals of another PC. Priority setting • When “Auto” is selected for , the monitor’s power-saving function works only when the two PCs are in the power-saving mode.
3-3 Connecting Peripheral USB Devices This monitor has a hub compatible with USB. Connected to a PC compatible with USB or another USB hub, this monitor functions as a USB hub allowing connection to peripheral USB devices. ● Required System Environment (1) A PC equipped with a USB port or another USB hub connected to a USB compatible PC (2) Windows 2000/XP/Vista or Mac OS 9.2.2 and Mac OS X 10.
Chapter 4 Troubleshooting If a problem still remains after applying the suggested remedies, contact your local dealer. • • • • • No-picture problems → See No.1 - No.2. Imaging problems (digital input) → See No.3 - No.8. Imaging problems (analog input) → See No.3 - No.12. Other problems → See No.13 - No.16. USB problems → See No.17. Problems 1. 2. Possible cause and remedy No picture • Power indicator does not light. • Check whether the power cord is connected correctly.
Problems Possible cause and remedy 5. Afterimages appear. • Use a screen saver or off timer function for a long-time image display. • Afterimages are particular to LCD monitors. Avoid displaying the same image for a long time. 6. Green/red/blue/white dots or defective dots remain • This is due to LCD panel characteristics and is not a on the screen. failure. 7. Interference patterns or pressure marks remain on • Leave the monitor with a white or black screen. The the screen. symptom may disappear.
Problems 17. The monitor connected with the USB cable is not detected. / USB devices connected to the monitor does not work. Possible cause and remedy • Check whether the USB cable is connected correctly. (see page 30) • Change the USB port to another one. If the PC or peripheral devices works correctly by changing the USB port, contact your local dealer. (Refer to the manual of the PC for details.) • Reboot the PC.
Chapter 5 Reference 5-1 Attaching an Arm The stand can be removed and replaced with an arm (or another stand) to be attached to the monitor. Use an arm or stand of EIZO option. 1 Lay the LCD monitor on a soft cloth spread over on a stable surface with the panel surface facing down. 2 Remove the stand. (Prepare a screwdriver.) 3 Attach the monitor to the arm or stand. 34 Unscrew the four screws securing the unit and the stand with the screwdriver.
5-2 Folding the EZ-UP stand Perform the following procedures to fold the stand when re-packing a monitor with an EZ-UP stand. 1 2 Remove the cable holder. Lower the monitor screen position until the hinge of the stand touches the stand base, and attach the lock metal fitting. Adjust the monitor angle so as the monitor screen not to touch the stand base. Lock metal fitting Hinge Stand Base 3 Fall the monitor screen backward with keeping slide-up the “Unlock” knob.
5-3 Specifications S2232W LCD Panel 22.0-inch (560 mm) TFT color LCD with anti-glare Viewing angle: Horizontal 178°, Vertical 178° (CR:10 or more) Dot Pitch 0.282 mm Horizontal Scan Frequency Analog: 31-82 kHz Digital: 31-65 kHz Vertical Scan Frequency Analog: 55-76 Hz (Non-interlace) (1680 × 1050: 55-61 Hz) Digital: 59-61 Hz (Non-interlace) (VGA TEXT: 69-71 Hz) Resolution 1680 dots × 1050 lines Max. Dot Clock Analog: 150 MHz Digital: 120 MHz Max. Display Color Approx. 16.
Mass Main unit (including Approx. 9.6 kg (21.2 lbs.) Height adjustable stand) Main unit (including Tilt stand) Approx. 7.6 kg (16.8 lbs.) Main unit (including EZUP stand) Approx. 11.4 kg (25.1 Ibs.) Main unit (without stand) Approx. 6.6 kg (14.6 lbs.) Movable range Environmental Conditions USB Height adjustable stand Tilt: 40° Up, 0° Down Swivel: 35° Right, 35° Left Adjustable height: 82 mm (3.
Analog Input Signal (Sync) Separate, TTL, positive/ negative Composite, TTL, positive/ negative Analog Input Signal (Video) Analog, Positive (0.7Vp-p/75Ω) Digital Signal Transmission System TMDS (Single Link) Video Signal Memory Analog signal: 45 (preset: 16) Digital signal: 10 Audio Output Speaker output: 0.5W + 0.5W (8Ω, THD: 3% or less) Headphone output: 2mW + 2mW Line input Input impedance : 48 kΩ (typ.) Input level :1.0 Vrms (Max.) Plug & Play VESA DDC 2B / EDID structure 1.
Vertical Scan Frequency Analog: 55-76 Hz (Non-interlace) (1920 × 1200: 55-61 Hz) Digital: 59-61 Hz (Non-interlace) (VGA TEXT: 69-71 Hz) Resolution 1920 dots × 1200 lines Max. Dot Clock Analog: 202.5 MHz Digital: 162 MHz Max. Display Color Approx. 16.77 million colors: Applicable to 8 bit (1064.33 million colors/10bit LUT) Display Area (H × V) 518.4 mm × 324.0 mm Power Supply 100-120 VAC ±10%, 50/60Hz 0.95A 200-240 VAC ±10%, 50/60Hz 0.
Environmental Conditions USB Temperature Operating temperature: 5 °C - 35 °C (41 °F - 95 °F) Storage temperature: -20 °C - 60 °C (-4 °F - 140 °F) Humidity Operating humidity: 30% - 80% R.H. (no condensation) Storage humidity: 30% - 80% R.H. (no condensation) Pressure Operating: 700 to 1,060 hPa Storage: 200 to 1,060 hPa Standard USB Specification Revision 2.0 Port Upstream port × 1, Downstream port × 2 Supply current Downstream: Max.
Outside Dimensions S2232W/S2242W (Height adjustable stand) 481.5(19) 168(6.6) 53.8 (2.12) 85 (3.35) unit : mm (inch) 35° 511(20.1) 475.8(18.7) 264.5(10.4) 17.6(0.69) 40° 205.5(8.1) 116.5(4.6) 100(3.9) 116.5(4.6) 82(3.23) 272.5(10.7) 491(19.3) 205.5(8.1) 20 (0.79) 208.5(8.2) 14.6 (0.57) 17.45 (0.69) 100(3.9) 106(4.2) 8(0.31) PIVOT 298.1(11.7) 333(13.1) 439～521(17.3～20.5) 90° 17～99(0.67～3.9) 528(20.8) 17.45 (0.69) 17.6(0.69) 35° SWIVEL 240.5(9.5) 325(12.
S2232W/S2242W (EZ-UP stand) 481.5(1.9) 129.3(5.1) 53.8 (2.12) 85 (3.35) unit : mm (inch) ° 172 172 ° SWIVEL (220) (208.5) 17.6(0.69) 94.5 (3.72) 64.3 (2.53) φ272(10.7) 100(3.9) 205.5(8.1) 116.5(4.6) 100(3.9) 116.5(4.6) 350(13.8) 165(6.5) 183.5(7.2) 13.4(0.53) 17.5 (0.69) PIVOT 536.5(21.1) 298.1(11.7) 333(13.1) 605.5(23.8) 516.5(20.3) 90° 205.5(8.1) 351.5(13.8) 17.5 (0.69) 25° 185(7.3) 511(20.1) 475.8(18.7) 17.6(0.69) 27.5 (1.08) 307.5(12.1) 279.
S2432W (EZ-UP stand) 532(20.9) unit : mm (inch) ° 172 172 ° SWIVEL 56.3(2.22) 85(3.35) 129.3(5.1) 566(22.3) 520.4(20.5) 22.8(0.9) 67(2.64) Ø272(10.7) 64.3(2.53) 233(9.2) 380.4(15) 133.5(5.3) 100(3.9) 133.5(5.3) 100(3.9) 196.9(7.8) 153.1(6) 350(13.8) 166.5(6.6) 13.4(0.53) 20.5(0.81) 633(24.9) PIVOT 233(9.2) 25° 552(21.7) 90° 326(12.8) 367(14.4) 533.5(21) 20.5(0.81) 22.8(0.9) 27.7(1.09) 307.6(12.1) 279.9(11) Connector Pin Assignment • DVI-D connector Pin No. Signal Pin No.
• D-Sub mini 15-pin connector Pin No. Signal Pin No. Signal Pin No. Signal 1 Red video 6 Red video ground 11 NC* 2 Green video 7 Green video ground 12 Data (SDA) 3 Blue video 8 Blue video ground 13 H. Sync 4 NC* 9 NC* 14 V. Sync 5 Ground 10 Ground 15 Clock (SCL) (NC*: No Connection) • USB port Upstream Upstream Series B connector Series A connector Contact No.
5-4 Glossary Clock The analog input monitor needs to reproduce a clock of the same frequency as the dot clock of the graphics system in use, when the analog input signal is converted to a digital signal for image display. This is called clock adjustment. If the clock pulse is not set correctly, some vertical bars appear on the screen. DDC/CI (Display Data Channel/Command Interface) VESA provides the standardization for the interactive communication of the setting information, etc.
Resolution The LCD panel consists of numerous pixels of specified size, which are illuminated to form images. This monitor consists of 1920 horizontal pixels and 1200 vertical pixels. At a resolution of 1920 x 1200, all pixels are illuminated as a full screen (1:1). sRGB (Standard RGB) International standard for “color reproduction and color space” among peripheral devices (such as monitors, printers, digital cameras, scanners).
5-5 Preset Timing The following table shows factory preset video timing (for analog signal only).
Congratulations! The display you have just purchased carries the TCO’03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also minimizes the Impact on our natural environment.
For U.S.A. , Canada, etc. (rated 100-120 Vac) Only FCC Declaration of Conformity We, the Responsible Party EIZO NANAO TECHNOLOGIES INC. 5710 Warland Drive, Cypress, CA 90630 Phone: (562) 431-5011 declare that the product Trade name: EIZO Model: FlexScan S2232W/S2242W/S2432W is in conformity with Part 15 of the FCC Rules.
Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor Dieser Monitor ist für Bildschirmarbeitsplätze vorgesehen. Wenn nicht der zum Standardzubehör gehörige Schwenkarm verwendet wird, muss statt dessen ein geeigneter anderer Schwenkarm installiert werden.
