User’s Manual Color LCD Monitor Important Please read this “User’s Manual”, and “PRECAUTIONS” (separate volume) carefully to familiarize yourself with safe and effective usage. ••Refer to the “Setup Guide” for information on the installation / connection of the monitor. ••For the latest product information including the “User’s Manual”, refer to our web site : http://www.eizoglobal.
Location of Caution Statement This product has been adjusted specifically for use in the region to which it was originally shipped. If operated outside this region, the product may not perform as stated in the specifications. No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
Notice for this monitor Aside from creating documents, viewing multimedia content, and other general purposes, this product is also suited to applications such as creating CAD data and other drawings (Assuming usage of approximately 12 hours per day). If using this product for the following kinds of applications, where an extremely high degree of reliability and safety is required, then measures should be in place to maintain safety while using this product.
Do not scratch or press on the LCD panel with any sharp objects, at this may result in damage to the LCD panel. Do not attempt to brush with tissues as this may scratch the panel. When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation may occur on the interior and exterior surfaces of the monitor. In that case, do not turn the monitor on. Instead wait until the dew condensation disappears, otherwise it may cause some damage to the monitor.
CONTENTS Notice for this monitor.......................................... 3 Chapter 5 Troubleshooting............................... 34 Cleaning..................................................................... 4 5-1. No Picture..................................................... 34 To use the monitor comfortably.............................. 4 5-2. Imaging Problems........................................ 35 CONTENTS.............................................................. 5 5-3.
Chapter 1 Introduction Thank you very much for choosing an EIZO color LCD monitor. 1-1. Features for DisplayPort over USB Type-C (DP Alt Mode) / USB Power ●●Support Delivery This product is equipped with a USB Type-C (USB-C) connector compatible with DP Alt Mode and USB Power Delivery. •• While being used as an external monitor of a notebook PC, this product can supply power to the PC.
●●High Degree of Flexibility for Installation •• This product can be used as an external monitor of a notebook computer. •• This product can be used in a multi-monitor configuration in which multiple monitors are connected to a single PC. ●●Reduction of Power Consumption This product provides a function that automatically adjusts the screen brightness to reduce power consumption *1. Power Reduction, CO2 Reduction, and Eco Performance Level can be checked on the "EcoView Settings" menu.
1-2. Controls and Functions ●●Front 5 1 5 2 3 4 1. Ambient light sensor Detects ambient brightness. If you use Auto EcoView, the screen brightness is automatically adjusted according to the ambient brightness (page 20). 2. Operation switches Displays menus. Operate the switches according to the operation guide (page 22). 3. Power switch Turns the power on or off. 4. Power indicator Indicates the monitor’s operation status.
●●Rear 11 6 12 7 13 15 14 16 10 8 6. 7. 8. 9. 10. 9 Handle Security lock slot Main power switch Power connector Input signal connectors This handle is used for transportation. Complies with Kensington’s MicroSaver security system. Turns the main power on or off. : On, : Off Connects the power cord. The following connectors are available on the monitor rear in order of left to right.
1-3. Supported Resolutions The monitor supports the following resolutions. ●●For DisplayPort Resolution Vertical scan frequency (Hz) Single screen and PinP display *1 Version 1.2 Version 1.1 PbyP display Dual screen display Quad screen display 720 × 400 70.087 √ √ √ √ 640 × 480 59.940 √ √ √ √ 640 × 480 60.000 √ √ √ √ 800 × 600 60.317 √ √ √ √ 1024 × 768 60.004 √ √ √ √ 1280 × 720 59.855 √ √ √ √ 1280 × 720 59.979 √ √ √ √ 1280 × 800 59.810 √ √ √ √ 1280 × 800 59.910 √ √ √ √ 1280 × 1024 60.
●●For HDMI Resolution Vertical scan frequency (Hz) 720 × 400 640 × 480 640 × 480 800 × 600 1024 × 768 1280 × 720 1280 × 720 1280 × 800 1280 × 800 1280 × 1024 1600 × 900 1600 × 1200 1680 × 1050 1680 × 1050 1920 × 1200 1920 × 1200 2560 × 1440 1280 × 1600 3840 × 2160 3840 × 2160 1920 × 2160 1920 × 2160 1280 × 720 1280 × 720 1280 × 720 1920 × 1080 1920 × 1080 1920 × 1080 1920 × 1080 1920 × 1080 720 × 480 720 × 480 720 × 480 720 × 480 720 × 576 720 × 576 3840 × 2160 3840 × 2160 3840 × 2160 3840 × 2160 3840 × 2
●●For USB-C Resolution Vertical scan frequency (Hz) Single screen and PinP display *1 4K UHD 60Hz 4K UHD 30Hz / USB2.0 / USB3.1 PbyP display Dual screen display Quad screen display 720 × 400 70.087 √ √ √ √ 640 × 480 59.940 √ √ √ √ 640 × 480 60.000 √ √ √ √ 800 × 600 60.317 √ √ √ √ 1024 × 768 60.004 √ √ √ √ 1280 × 720 59.855 √ √ √ √ 1280 × 720 59.979 √ √ √ √ 1280 × 800 59.810 √ √ √ √ 1280 × 800 59.910 √ √ √ √ 1280 × 1024 60.020 √ √ √ √ 1600 × 900 60.000 √ √ √ √ 1600 × 1200 60.000 √ √ √ √ 1680 × 1050 59.
1-4. Changing the Computer Display Settings If the image is not displayed properly after connecting the monitor to a PC, follow the procedure below to change the display settings on the computer. ●●Windows 10 1. Right-click the mouse anywhere on the desktop except on icons. A menu is displayed. 2. From the displayed menu, click “Display Settings”. The “Settings” screen is displayed. 3.
Chapter 2 Basic Adjustment / Setting This product enables users to change the brightness according to personal preference or to suit the usage environment and reduce power consumption to conserve energy. This chapter describes the basic functions that can be adjusted and set using the switches on the front of the monitor. For advanced adjustment and setting procedures using the Setting menu, see “Chapter 3 Advanced Adjustment / Setting” (page 22). 2-1. Switch Operation Method 1.
2-2. Switching Input Signals When a monitor has multiple signal inputs, the signal to display on-screen can be changed. Note •• "Screen InStyle" allows you to switch input signals using the shortcut keys on the keyboard. ●●PbyP display By selecting PbyP (Picture by Picture) display when a monitor has multiple input signals, windows can be displayed side-by-side (dual screen) or side-by-side and above-and-below (quad screen).
Function PbyP Settings Input Setting Value Description Left USB-C DisplayPort HDMI 1 HDMI 2 Select an input signal to be displayed on the left screen of the PbyP display (dual screen). Right USB-C DisplayPort HDMI 1 HDMI 2 Select an input signal to be displayed on the right screen of the PbyP display (dual screen). Upper Left USB-C DisplayPort HDMI 1 HDMI 2 Select an input signal to be displayed on the upper left screen of the PbyP display (quad screen).
●●PinP display By selecting PinP (Picture in Picture) display when a monitor has multiple input signals, a large window and a small window can be displayed. Because multiple windows can be displayed on a single monitor, the need for changing between signals is eliminated, which leads to increased work efficiency. By selecting PinP display, the combination of the signals to display on the large and small windows can be switched.
2-3. Switching Display Modes (Color Modes) This product is preinstalled with color modes for various display purposes. By switching the mode according to the purpose and contents of the display, you can display images in an appropriate manner. ●●Display Modes Color Mode User1 User2 sRGB Purpose Select either of these modes to set a user-defined display mode.
2-4. Conserving Energy This monitor is equipped with EcoView functions to enable users to conserve energy. You can use this function to curtail unnecessary power consumption and save on electricity expenses. Saving power also reduces carbon dioxide emissions. Note •• The power saving level (Power Reduction, CO2 Reduction, and Eco Performance Level) can be checked on the “EcoView Settings” menu.
Function Auto EcoView Setting Value On Off Description The ambient light sensor on the front of the monitor detects the ambient brightness to automatically adjust the screen brightness to a comfortable level using Auto EcoView. The power consumption of the backlight can be curtailed by adjusting the brightness to an appropriate level. This function can also mitigate eye strain and tiredness caused by a screen that is too bright or too dark.
2-5. Adjusting Brightness The brightness of the screen can be adjusted to suit the installation environment or personal preference. The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD back panel). Setting Value 0 to 100 2-6. Adjusting Volume The volume of the speakers and headphones can be set individually.
Chapter 3 Advanced Adjustment / Setting This chapter describes the advanced monitor adjustment and setting procedures using the Setting menu. For basic functions, see “Chapter 2 Basic Adjustment / Setting” (page 14). 3-1. Basic Operation of the Setting Menu 1. Menu display 1. Touch any switch (except ). The operation guide appears. 2. Select . The Setting menu appears. 2. Adjusting / setting 1. Select a menu to adjust / set with and select . and select . The Sub menu appears. 2.
3-2. Setting Menu Functions ●●Color Adjustment The color mode setting status can be adjusted according to personal preference. Functions that can be adjusted differ depending on the color mode.
Function Color Mode Brightness Setting Value Description User1 User2 sRGB Paper Movie DICOM Select the desired mode according to the monitor application. The color setting status can also be adjusted according to personal preference. Select the mode for adjustment and perform adjustment using the relevant functions. 0 to 100 The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD back panel).
Setting Value Function Advanced Overdrive Enhanced Settings Standard Off Hue -50 to 50 Description This function allows you to set the overdrive intensity based on the use of the monitor. Image lag can be reduced by using the “Enhanced” setting when displaying moving images. Adjust the hue. Note •• Using this function may prevent some color gradations from being able to be displayed. Saturation -50 to 50 Adjust the color saturation.
●●Signal Settings Set the details regarding input signal, such as the screen display size and color format. Function Window Selection Setting Value Left Right Upper Left Lower Left Upper Right Lower Right Large Window Small Window Description Select the target for the signal settings. When using PbyP/PinP display, select this target first. •• “Left” The setting is applied to the left screen in PbyP display (dual screen).
Function Picture Expansion Setting Value Auto *1 Full Screen Aspect Ratio Dot by Dot Description The screen size of the monitor display can be changed. •• “Auto” The monitor automatically changes the screen size according to the aspect ratio and resolution information from the PC. •• “Full Screen” Images are stretched to full screen. Since aspect ratios are not maintained, images may be distorted in some cases. •• “Aspect Ratio” Images are enlarged to full screen without changing the aspect ratio.
●●Preference Settings The monitor’s settings can be configured to suit the usage environment or personal preference. Function Setting Value Description USB CHARGE Normal The USB downstream port of the monitor supports boost charging via Port Charging Only USB 3.0. By changing this setting to “Charging Only”, the device connected to the port can be charged in a shorter period of time than that which would be required when it is set to “Normal”.
Setting Value Function Sound Selection Description Left Select the source of audio to output from the monitor during PbyP/PinP Right display. •• “Left” Upper Left Lower Left Outputs the audio source from the left screen during PbyP display (dual Upper Right screen). •• “Right” Lower Right Large Window Outputs the audio source from the right screen during PbyP display (dual Small Window screen). •• “Upper Left” Outputs the audio source from the upper left screen during PbyP display (quad screen).
●●Information Monitor information (product name, serial number, usage time, resolution, and input signal) can be checked.
Chapter 4 Administrator Settings This chapter describes how to configure monitor operation using the “Administrator Settings” menu. This menu is for administrators. Configuration on this menu is not required for normal monitor use. 4-1. Basic Operation of the “Administrator Settings” Menu 1. Menu display 1. Touch to turn off the monitor. 2. While touching the leftmost switch, touch for more than 2 seconds to turn on the monitor. The “Administrator Settings” menu appears. 2. Setting 1.
4-2. Functions of the “Administrator Settings” Menu Function Setting Value Auto Input Detection On Off Description This function automatically recognizes the connector through which PC signals are input, and displays images on the screen accordingly. •• “On” When the monitor is connected to multiple PCs, if a specific PC enters power saving mode or no signals are input to the monitor, the connector is automatically changed to another one to which signals are input.
Function HDMI 1 Setting Value 4K UHD 60Hz 4K UHD 30Hz Description The types of signals that the monitor can display can be changed. Note •• If the HDMI signal that is being input is not displayed, change this setting. HDMI 2 4K UHD 60Hz 4K UHD 30Hz The types of signals that the monitor can display can be changed. Note On-Screen Logo On Off Key Lock Off Menu All •• If the HDMI signal that is being input is not displayed, change this setting.
Chapter 5 Troubleshooting 5-1. No Picture Problem 1. No picture •• Power indicator does not light up. •• Power indicator is lighting white. •• Power indicator is lighting orange. •• Power indicator is flashing orange and white. 2. The message below appears. 34 Possible cause and remedy •• •• •• •• Check whether the power cord is connected properly. Turn on the main power switch on the rear side of the monitor. Touch .
5-2. Imaging Problems Problem 1. The screen is too bright or too dark. 2. Brightness cannot be changed or it changes on its own. 3. Text is blurred. 4. Afterimages appear. 5. Green / red / blue / white / dark dots remain on the screen. 6. Interference patterns or pressure marks remain on the screen. 7. Noise appears on the screen. 8. The positions of windows and icons are shifted when the monitor is turned off / on or when restored from power saving mode. 9. The color shown on the screen is not correct.
5-3. Other Problems Problem 1. The Setting menu does not appear. 2. Cannot select items in the Settings menu. •• Check whether the switch operation lock function is active (see “Key Lock” (page 33)). •• Items that are displayed with gray text cannot be changed. 3. No audio output. •• Check whether volume is set to 0. •• Check the PC and audio playback software to see whether they are configured correctly. •• Check the “Sound Selection” setting during PbyP/PinP display (see “Sound Selection” (page 29)).
Chapter 6 Reference 6-1. Attaching the Optional Arm An optional arm (or an optional stand) can be attached by removing the stand section. Please refer to our web site for the supported optional arm (or optional stand). http://www.eizoglobal.com Attention •• When attaching an arm or stand, follow the instructions of the respective User’s Manual. •• When using another manufacturer’s arm or stand, confirm the following in advance and select one conforming to the VESA standard.
●●Attaching the optional arm (or optional stand) 1. Lay the LCD monitor on a soft cloth spread over a stable and flat surface with the panel surface facing down. 2. Remove the stand. As shown in the figure, while holding down the lock button (1), slide the stand toward the stand base until it touches the stand base (2). Then, lift the stand up (3). (3) (1) (2) 3. Attach the arm or stand to the monitor. Use the VESA mounting screws supplied with this product when attaching the arm or stand.
6-2. Detaching/Attaching the Cable Holder ●●Detaching the cable holder 1. Slide the cable holder to the left, and detach it from the stand. ●●Attaching the cable holder 1. Align the tabs of the cable holder with the attachment parts of the stand. 2. Slide the cable holder to the right, and attach it to the stand.
6-3. Detaching / Attaching the Cable Cover ●●Attaching the cable cover A B 1. Align the tabs of (A) with the attachment parts of the stand. A 2. Slide (A) downward to secure the tabs to the attachment parts of the stand. 3. Check the tabs of (B) (four locations indicated by A 40 Chapter 6 Reference ) and the attachment locations of (A).
4. Pass the cables between (A) and (B), and align (B) with (A) to fit in. 5. Slide (B) downward and secure it to (A). ●●Detaching the cable cover 1. Slide (B) upward, and detach it from (A). 2. While holding down of (A) lightly, slide (A) upward to detach it from the stand.
6-4. Connecting Multiple PCs This product can be connected to multiple PCs and allows you to switch between the connections for display. ●●Connection examples HDMI HH200PR (HDMI - HDMI) HDMI (supplied) DisplayPort PP200 (DisplayPort - DisplayPort) DisplayPort (supplied) USB-C CC200SS (USB-C - USB-C) USB-C (supplied) Note •• You can select the input signal to display using the operation switch on the front of the monitor. For details, see “2-2. Switching Input Signals” (page 15).
6-5. Using the USB Hub Function This monitor is equipped with a USB hub. It functions as a USB hub when connected to a USBcompatible PC, allowing the connection of peripheral USB devices. ●●Connection procedure 1. Connect the USB cable between the USB-C connectors of the PC and the monitor. 2. Connect a peripheral USB device to the USB downstream port of the monitor. Attention •• If your PC is not equipped with a USB-C connector, a USB-C to Type-A conversion cable is required.
6-6. Specifications LCD Panel Type Backlight Size IPS (Anti-Glare) LED 80.0 cm (31.5 inch) Resolution 3840 dots x 2160 lines Display Size (H × V) 697.3 mm × 392.2 mm Pixel Pitch 0.182 mm Display Colors 8-bit colors: 16.
Power Physical Specifications Input 100 - 240 VAC ±10 %, 50 / 60 Hz 1.65 A - 0.75 A Maximum Power Consumption Power Save Mode 163 W or less 0.5 W or less (no USB device connected, default settings) Standby Mode 0.5 W or less (no USB device connected, default settings) Dimensions 717.4 mm × 396.1 mm to 591.1 mm × 253.4 mm to 287.8 mm (W × H × D) (Tilt: 35˚) 717.4 mm × 427.3 mm to 576.2 mm × 230 mm (W × H × D) (Tilt: 0˚) 717.4 mm × 416.3 mm × 51.
Appendix Trademark The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing, LLC in the United States and other countries. The DisplayPort Compliance Logo and VESA are registered trademarks of the Video Electronics Standards Association. The SuperSpeed USB Trident Logo is a registered trademark of USB Implementers Forum, Inc. The USB Power Delivery Trident logos are trademarks of USB Implementers Forum, Inc.
FCC Declaration of Conformity For U.S.A., Canada Only FCC Declaration of Conformity We, the Responsible Party EIZO Inc. 5710 Warland Drive, Cypress, CA 90630 Phone: (562) 431-5011 declare that the product Trade name: EIZO Model: FlexScan EV3285 is in conformity with Part 15 of the FCC Rules.
03V27413A1 UM-EV3285 Copyright © 2018 EIZO Corporation. All rights reserved.
