- For Administrator - For Microsoft Windows XP Embedded Version A Please confirm the version of the software built in eClient, and refer to the suited User's Manual (Refer to the User's Manual Version List on next page). This is the manual for the following software version. * Microsoft Windows XP Embedded: Ver. 5.01 or later, Rev. 1.0.2 or later * Microsoft Remote Desktop Connection Software: Ver. 5.2.3 or later * Ctrix ICA Client Software: Ver. 8.
User’s Manual Version List A handling description changes with versions of the software built in eClient. Please refer to below. NOTE • The version of software built in eClient can be checked with a [System] tab of [Start]- [About] menu. OS: Microsoft Windows XP Embedded Software Manual A (This manual) Microsoft Windows XP Embedded Microsoft Remote Desktop Connection Software ICA Client Software Version 5.01 or later Rev. 1.0.2 or later Version 5.2.3 or later Version 8.
SAFETY SYMBOLS This manual uses the safety symbols below. They denote critical information. Please read them carefully. WARNING Failure to abide by the information in a WARNING may result in serious injury and can be life threatening. CAUTION Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage. Indicates a prohibited action. Indicates to ground for safety. Copyright© 2004 EIZO NANAO CORPORATION. All rights reserved.
TABLE OF CONTENTS 1. INTRODUCTION ..................................................................................... 5 1-1. General Description ......................................................................................5 1-2. Features ........................................................................................................5 1-3. Package Contents..........................................................................................6 1-4. Controllers & Connectors ..............
1. INTRODUCTION Thank you very much for purchasing the EIZO eClient SX1. 1-1. General Description The SX1 is used as a thin client, which connects to the terminal service installed Windows Terminal Server (Hereafter defined WTS) as listed below and accesses applications or data provided from the WTS.
• Secondary power switch (wired) 1-3. Package Contents Please contact your local dealer for assistance if any of the listed items are missing or damaged. Please make sure that all the items listed are in the package. • SX1 • Mouse (FDM-LCS1) • Power Cord • Switch Box (1.
1-4. Controllers & Connectors Controllers Left View Right View Po we r SY NC OF ON F (5) AC OUT PU T AC INPU T (3) (1) (2) (4) (1) Power Button (2) Power Indicator Power Indicator Blue * SX1 used as an example State of the unit • Operation mode • Screen saver is active *1 • No picture is displayed on the monitor *1, *2 Off *1 *2 Power is off (Wake on LAN standby) [Procedure to return to the operation mode] - Operate the mouse or keyboard.
Connectors Pow (1) er SY NC OFF (6) ON AC (2) (3) OU TP UT AC INP UT (7) (4) (8) (9) (5) (10) (11) (12) (1) (2) (3) (4) (5) (6) Power Supply Control Switch (POWER SYNC)…Same with (5) on P.
2. CONNECTION the eClient SX1 This chapter explains how to connect the SX1 to a WTS. 2-1. Setting up the SX1 Please observe the following cautions when connecting the SX1. WARNING Place the eClient SX1 on a strong, stable surface. A unit placed on an inadequate surface may fall, resulting in injury or equipment damage. If the unit falls, disconnect the power immediately and have the unit checked by a qualified service engineer before using it again.
Mounting EIZO monitor to the SX1 When using other monitors than EIZO, proceed to step 3. The Monitor Attachment Unit of SX1 supports the EIZO L767, L567, L557, and L367, so EIZO monitor mounted SX1 is available. NOTE • Prepare the following, when mounting a monitor to the SX1. Monitor L767, L567, L557, L367 Screws The screws used for the monitor original stand Power Cord Power Cord (50 cm) which is included into the SX1 package. Mounting EIZO monitor procedure Step 1.
(2) Lay the LCD monitor down on the soft cloth or cushion not to scratch the panel surface. (3) Remove the original stand by loosening the screws. (4) Attach the monitor attachment unit to the monitor securely, by using the screws, which used for the original stand. 100 mm x 100 mm for L567/L557/L767 75 mm x 75 mm for L367 (5) Get back the cover to the monitor attachment unit. 2. Mount the monitor to the SX1.
Connecting the signal cable and power cables 3. Plug the signal cable into the connector at the rear of the monitor and the other end of the cable into the video connector on the DVI-I connector of the SX1 4. After connecting, secure the connection with the screw-in fasteners. 5. Plug the power cord (50 cm), included into the package, into the power connector on the rear of the monitor and the other end of the cable into the power connector (AC outlet) of the eCleint, or into a power outlet.
NOTE • Bundling cables After all connection has been made, please bundle the cables with the clamp included into the package, so that the cables do not obstruct the paths as follows. • Clamp installation Po we r SY NC OF F ON AC AC PO QO O| PQ O OU | Q S O u ‘ TP O u ‘ Q ‘ UT Q ‘ IN PU T Connecting the peripheral devices to SX1 NOTE • Before connecting the SX1, confirm the following: - The SX1 is turned off. - The WTS is turned on.
9. The switch box is connected to the attached connector for Switch box on the SX1 if needed. The secondary power switch makes it easy to turn the SX1 on and off when stowed away under the desk or out of reach. When the switch box is connected to the connector, it can be used as a power button. The power button on the SX1 can be used simultaneously even if the switch box is connected. 10. If using other devices, please connect them to the appropriate connectors. 11.
3. OPERATION This chapter shows how to start and end SC1/SX1 operation. 3-1. Adding a Connection name When using the RDP protocol 1. Turn on the SX1. 2. The Desktop screen will be displayed. 3. Star the [Remote Desktop Connection]. Double click the [Remote Desktop Connection] icon to open the [Remote Desktop Connection] dialog box. Click [Start]-[Remote Desktop Connection] to open the [Remote Desktop Connection] dialog box.
5. Set up connection settings of each setting tab of [Options] with reference to the setting method of Windows. 6. Name the file name and save it. (1) Click [Save As] of [Connection settings] of the [General] tab. (2) Name the file (The example is “RDP1.rdp”.), and save it. 16 3.
7. A new icon (The example is “RDP1”) is displayed on the desktop. If a setup finishes, click [Connect] and log on to the WTS, or click [Close] and end a setup. 3.
When using the ICA protocol 1. Turn on the eClient SX1. 2. The Desktop screen will be displayed. 3. Double click the [Citrix Program Neighborhood] icon to open the Citrix program. Click [Start]-[Citrix Program Neighborhood] to open the Citrix program. Click [Start]-[Program]-[Citrix]-[MetaFrame Access Clients]-[Program Neighborhood] to open the Citrix program. 4. The [Citrix Program Neighborhood] will be displayed. Double click the [Add ICA Connection]. 18 3.
5. “Add New ICA Connection” Wizard is displayed. Set up the SX1 according to the directions of the displayed dialog box. 6. The last page of the wizard is displayed and click [Finish], a new icon (The example is “ICA1”) is added in the “Citrix Program Neighborhood-Custom ICA Connections” dialog box. 7. If a setup finishes, click [Connect] and log on to the WTS, or click [Close] and end a setup. 3.
3-2. Logging on or off the WTS Logging on to the WTS 1. Turn on the SX1. 2. The Desktop screen will be displayed. When using the RDP protocol, proceed to step 3, and when using the ICA protocol, proceed to step 4. 3. When using the RDP protocol In case the connection icon exists on the desktop (1) Double click the connection icon (The example below is “RDP1”.). In case the connection name doesn’t exist on the desktop 20 3.
(2) Double click the [Remote Desktop Connection] icon to open the [Remote Desktop Connection] dialog box. Click [Start]-[Remote Desktop Connection] to open the [Remote Desktop Connection] dialog box. Click [Start]-[Program]-[Remote Desktop Connection] to open the [Remote Desktop Connection] dialog box. (3) The [Remote Desktop Connection] will be displayed. Enter the name of the computer and click [Connect]. Proceed to step 5. 4.
(5) The [Citrix Program Neighborhood] will be displayed. Double click the connection icon (The example below is “ICA1”). 5. When the SX1 connects to the WTS, the “Log On to Windows” dialog box is displayed. Enter your [User name] and [Password], and then click [OK] to log on to the WTS. After logging on, the SX1 allows you to use the Microsoft Windows applications running on the WTS.
Logging off the WTS If your SX1 starts its operation with a desktop: 1. Log off the WTS. (1) Close all the applications. (2) Select [Start] on the taskbar. (3) Select [Shut Down...] and select [Logoff] of the [Shut Down Windows] dialog box. (4) 2. Click [OK] on the Logoff Window. The session ends and logs off from the WTS automatically. Shut down the SX1. Click [Start] and select [Shut Down…] and select the [Shut Down] of the [Shut Down Windows] dialog box.
3-3.Opening/Closing the Local Web Browser Opening the Local Web Browser 1. Turn on the SX1. 2. The desktop screen will be displayed. 3. Double click the [Internet Explorer] icon to open the browser. Click [Start]-[Internet Explorer] to open the browser. Click [Start]-[Program]-[Internet Explorer] to open the browser. 4. The local web browser opens. It is possible to browse web pages on the Internet. Closing the Local Web Browser 1. Close the local web browser.
4. Setup the environment of the operation (by the System Administrator) This chapter explains that the information on SX1 and a setup of detailed environment of operation. The “Administrator” authority performs a setup the environment. When the SX1 is turned on, it logs on automatically by “User” authority. In order to perform each setup, it is necessary to log on by the “Administrator” authority. 4-1. Note for the SX1 system environment Please note the followings as the system information of SX1.
Power save setting • Do not use [System standby] setting on the power scheme setting of the control panel, since the connection with WTS is disconnected when the SX1 shift to system standby. When the SX1 is used again, you should reconnect to the WTS (Refer to P.35). 4-2. Log on to the SX1 as the System Administrator Account information The following is the default user names and passwords, which are used for logging on to the SX1 (“User” authority and “Administrator” authority).
2. Log off the SX1 as the “User” authority and log on it as the “Administrator” authority. (1) Click [Start] and select [Shut Down…] and select [Log off User] of the [[Shut down Windows]. (2) Click [OK] by pressing the [Shift] key on the keyboard. (3) The [Log On to Windows] is displayed on the screen, appears, enter “Administrator” in the [User name] and “Administrator” in the [Password] column and click [OK]. NOTE • Password is case sensitive. 3. The Desktop screen of System administrator is displayed.
4-3. “User” authority and “Administrator” authority The operation, which can be operated by the “Administrator“ authority is different from the “User” authority. For the detailed setting as the “Administrator” authority for the “Control panel” and [Start]-[About] menu, please refer to “4-4. Using the control panel” and “4-5. [Start]-[About] menu.
[Start]-[About] menu The information about eClient is displayed. For details, please refer to "4-5. [Start][About] menu" Tab [General] [Security] [System] Administrator √ √ √ User √ N/A √ 4.
4-4. Using the control panel Each function of the Control panel and the [About] menu perform various setup of SX1. Log on and set up by “Administrator” authority. About each function of a control panel, it is the standard function of Windows. In this section, we explain only functions, which we add to use them for SX1. Control panel by logging on as the administrator Administrative Tools NOTE • “Help and Support” function doesn’t support SX1 30 4.
Control panel items Gray shade items are EIZO customized functions.
Terminal Logon By enabling the automatic logon, it logs automatically by the user name at the time of starting (i.e. power supply ON). Set up a user name and a password. [Enable auto logon to terminal] ...................................Enable or disable of the automatic logon function to SX1 is set up. It is applied from next logoff or a next starting up after setting. When this setting is disabling, “Log on to Windows” dialog box is displayed at starting up. [User settings] .....................
RAM Disk The size of a RAM disk drive is set up. This RAM disk is volatile disk, and is used as temporary data storage. Drive letter “Z:” is assigned to the RAM disk. [RAM Disk Settings] ...................................The current RAM disk drive is displayed. Moreover, the size of a RAM disk is set up in 4 to 30MB of range. A changed setup is adapted after restarting. The following items are stored on the RAM disk.
Administrative Tools-Enhanced Write Filter Control Enhanced Write Filter (EWF) forbids the unnecessary writing to Flash Memory (C: drive) where software (OS, application, user setup) is saved, and improves the security and robustness of SX1. NOTE • In order to prevent the unusual writing to Flash Memory (C: drive), when usually using the SX1, be sure to use EWF in the state of enable (writing the Flash Memory (C: drive) is prohibited).
Display- [Screen Saver] tab A connection monitor's Screen Saver and a setup of power-saving control are [Control Panel]-[Display]-[Screen Saver] tab and set up them by this tab. A powersaving control setup of the SX1 should use [Turn off monitor]. NOTE • Do not use [System standby] setting, since the connection with WTS is cut when the SX1 shift to system standby. When the SX1 is used again, you should reconnect to the WTS. • The control by using the Network Administrator 3.
Power saving Set here Never to set this function Click [Monitor Power] [Power Schemes] tab-[Turn off monitor] ............................................Set the screen saver pattern, waiting time (for activating), and the password to resume the screen saver (The default is None). NOTE • Set the power save setting of the connection monitor.
4-5. [Start]-[About] menu The [Start]-[About] menu of Windows shows the SX1 information and performs an IP address setup of the management console for software Network Administrator Version 3.0 which manages the client terminals. General [General] tab shows the product name, Product ID, Windows XPe Revision, version, Build No. Security Assign the IP address of the computer, which the Network Administrator is installed (NA service running computer).
System [System] tab shows the product information. [Software] ...........................Microsoft Windows XPe Version, Revision, Build number. Windows Terminal Server client Revision. [Hardware] .........................Serial number of the SX1 [Network] ...........................Network information 4-6. Software updating/Installation The software backup and update of SX1 is performed using thin client utility software “Network Administrator”.
5. TROUBLESHOOTING This page presents problem that can be corrected by the user. If a problem persists even after applying the suggested remedies, contact an EIZO dealer. Problems Points to check with possible solutions 1. No picture is displayed on the screen (The power indicator is off). Check if the power is OFF. 2. No picture is displayed on the screen (The power indicator is blue). Check if the power of the monitor is OFF. Check brightness setting. Minimum settings will cause screen to be blank.
6. CLEANING Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime. NOTE • Never use thinner, benzene, alcohol (ethanol, methanol, or isopropyl alcohol), abrasive cleaners, or other strong solvents, as these may cause damage to the cabinet. Cabinet To remove stains, wipe the cabinet with a soft, lightly moistened cloth using a mild detergent. Do not spray wax or cleaner directly onto the cabinet. 40 6.
7. SPECIFICATIONS CPU and Memory CPU VIA Eden, 800 MHz Memory RAM: 256 MB, ROM: 256 MB Display Color 256 / 65536 / 16 M colors Supported Resolution 1280 × 1024 (60 Hz) 1024 × 768 (60 Hz) 800 × 600 (60 Hz) Complying Protocol Microsoft Remote Desktop (RDP) Citrix Independent Computing Architecture (ICA) Software Microsoft Windows XP Embedded with SP1 TM Java VM - Sun Microsystems Java 2 Runtime Environment Version Microsoft RDP Client Citrix ICA Client 8.
Dimensions (eClient only) mm (inches) 166(6.5) 55( 27(1.06) 2.1 200(7.9) 7) 63( 2 5(0 .48) .2) Po we r SY 89(3.5) NC OF F ON 295(11.6) AC TP UT INP UT 60 214(8.4) 12(0.47) 156(6.1) 178(7.0) AC OU 22(0.
L557/L567 L767 7.
