重要 ご使用前には必ず本取扱説明書をよくお読みになり、正しくお使いくださ い。この取扱説明書は大切に保管してください。 Important Please read this User’s Manual carefully to familiarize yourself with safe and effective usage. Please retain this manual for future reference.
SAFETY SYMBOLS This manual and this product use the safety symbols below. They denote critical information. Please read them carefully. WARNING Failure to abide by the information in a WARNING may result in serious injury and can be life threatening. Indicates an attention to be required. Indicates a prohibited action. Using the special functions, such as screen size change (ex.
PRECAUTIONS IMPORTANT • This product is intended to be used with an industrial device designed to build industrial systems. -- Transportation systems (Ship, aircraft, train, automobile, etc.) -- Safety devices (Disaster prevention system, security control system, etc.) -- Equipment with direct effect on human life (Life support systems, Medical equipment or devices used in the operating room, etc.
Notice for this monitor This product may not be covered by warranty for uses other than those described in this manual. Only use optional products manufactured or specified by us with this product. As it takes about 30 minutes for the performance of electrical parts to stabilize, adjust the monitor 30 minutes or more after the monitor power has been turned on. Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and maintain a stable display.
Cleaning ATTENTION • Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the panel, and also quality deterioration of the image. • Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the panel. • Do not allow liquid to enter the clearance between the panel and the panel frame. NOTE • The optional ScreenCleaner is recommended for cleaning the panel surface.
CONTENTS Cover ................................................................... 1 PRECAUTIONS................................................. 3 Notice for this monitor............................................... 4 CONTENTS.............................................................. 6 Chapter 1 Introduction.......................................... 7 1-1. Features............................................................... 7 1-2. Package Contents...............................................
Chapter 1 Introduction Thank you very much for choosing an EIZO color LCD monitor. 1-1. Features • FDX1001T/FDV1001T: 10.4-inch screen, FDX1201T: 12.
Chapter 2 Assembly ATTENTION • Before mounting the monitor into the enclosure, please perform all settings and adjustments. Please refer to the Touch Panel Driver User’s Manual (on the CD-ROM) when installing the touch panel driver. For information on how to apply settings and adjustments, please refer to “Chapter 3 Settings and Adjustments”.
FDX1201T 10 (0.39) 272 (10.7) 21.5 (0.85) 293 (11.5) 10.5 (0.41) 10.5 (0.41) 46 (1.81) 10 (0.39) 1 (0.04) unit : mm (inch) Button extension connector Connector specifications: see *2 below M4 (VESA mounting holes) 52 (2.05) 10 (0.39) 86.5 (3.41) 108 (4.3) 243 (9.6) 37.5 (1.48) 146 (5.7) 116 (4.6) 185.5 (7.3) (Dimension available for touch panel input) 33.9 (1.33) 100 (3.9) DC power terminal block Power specifications: see *1 below 32.8 (1.29) 127 (5.0) 247 (9.
Panel mount type ● Exterior view FDX1001T / FDV1001T unit : mm (inch) 113 (4.4) 19 (0.75) 217 (8.5) 219±0.5 (8.6±0.02) Max.17 (0.67) Max.17 (0.67) （Panel opening dimensions） 100 (3.9) 24 (0.94) 35 (1.38) 92 (3.62) M4 (VESA mounting holes) Max.16 (0.63) 92 (3.62) 100 (3.9) 16 (0.63) 11 (0.43) 38 (1.50) 130 (5.1) 42 (1.65) 45 (1.77) 1 (0.04) Max.16 257±0.5 (10.1±0.02) (0.63) （Panel opening dimensions） 16 (0.63) 132 (5.2) DC power terminal block 52 (2.
*1 DC power terminal block Connector Pin Assignment Pin No. 1 2 1 2 3 3 * *2 Power sequencing Signal DC12V DET* Ground Not connected DC12V 10V 10V 5V t1 t1 < 50ms 30ms < t2 t2 Button extension connector:S3B-PH-SM4-TB(LF)(SN) (JST) Connector Pin Assignment Pin No. 1 2 3 Signal KEY0 KEY1 Ground ● How to assemble ATTENTION • Since the panel mounted on the monitor is tightened with a metal panel fitting screw, please make the selection considering the following points.
2. Fit the included metal panel fittings onto the monitor (4 locations). Metal panel fitting 3. Tighten the screws of the metal panel fittings with a prescribed torque of 0.6-0.7 N·m.
Chapter 3 Settings and Adjustments 3-1. Buttons Chassis mount type Top 1 2 1 2 3 4 5 Panel mount type Top 1 button 2 button 3 4 3 4 5 Switches the input signal. button button 5 Power indicator Displays the Setting menu, fixes the setting or adjustment items on each menu, and saves the setting or adjustment results. • Used to select the setting or adjustment items, or to increase or decrease the adjustment values on each menu.
3-2. Basic Operation and Functions Basic operation of Setting menu 1 Displaying Setting Menu Press . 2 Setting/Adjusting 3 Exiting Choose [Exit] with or , and press . NOTE • Keeping 14 pressed for 2 seconds will also exit the Setting menu.
Functions The settings adjustable in the Setting menu are as shown below. The availability of items depends on the input signal. √ : Configurable ― : Not configurable Tab Color Setting / adjustable item Setting / adjustable value PC Video Setting / adjustable content Brightness 0 - 30 √ √ Adjusts the brightness of the backlight. Contrast 0 - 30 √ √ Adjusts the contrast. Black Level 0 - 30 √ √ Adjusts the image brightness. Sharpness Off/Low/High ― √ Adjusts the image outlines.
Tab Setting / Setting / adjustable item adjustable value Others Video Aspect Normal/100% PC Video ― √ Setting / adjustable content Configures the display range of the input image (overscan). “Normal” : Displays the input image with the outmost parts slightly cut off. * This is how display devices normally display images. “100%” : Displays most of the input image.
Chapter 4 Troubleshooting If a problem still remains after applying the suggested remedies, contact your local dealer. Common Problems Possible cause and remedy No picture • Power indicator does not light. • Check whether the power cord is connected correctly. • If the problem persists, turn off the power, and then turn it on again a few minutes later. • Power indicator lights orange. • Press • Power indicator lights blue. • Check whether the power of the connected device is turned on.
Touch panel problems 18 Problems Possible cause and remedy Cursor position is not correct. / Cursor jumps. • Turn off and on the monitor. If the symptom is not improved, perform the calibration on the monitor. • Touch with one finger only. • Connect the monitor to the PC with the cable indicated in the User’s Manual of the monitor. Using a conversion adapter, the touch panel may not operate properly. Touch operation is not effective.
Chapter 5 Reference 5-1. Specifications FDX1001T LCD Panel Size 10.4-inch (260 mm) TFT color LCD Surface treatment Anti-glare Surface hardness 2H Viewing angle Horizontal 160°, Vertical 130° (CR : 10 or more) Dot Pitch 0.2055 mm Display Area (H × V) 210.4 mm × 157.8 mm Resolution 1024 dots × 768 lines Max. Display Color Approx. 16.7 million colors PC input Horizontal Scan Frequency 24-50 kHz Vertical Scan Frequency 55-75 Hz (Non-interlace) Max.
Environmental Temperature Conditions [Operating temperature] 0 °C - 50 °C (32 °F - 122 °F) [Storage temperature] -20 °C - 60 °C (-4 °F - 140 °F) Humidity [Operating humidity] 20% - 90% R.H. (wet bulb temperature ≤ 39 °C (102 °F), no condensation) [Storage humidity] 10% - 90% R.H. (wet bulb temperature ≤ 39 °C (102 °F), no condensation) Pressure [Operating] 700 hPa - 1060 hPa [Storage] 200 hPa - 1060 hPa Size 10.
Mass Chassis mount type Approx. 2.0 kg (4.4 lbs.) Panel mount type Approx. 2.3 kg (5.1 lbs.) Environmental Temperature Conditions [Operating temperature] 0 °C - 50 °C (32 °F - 122 °F) [Storage temperature] -20 °C - 60 °C (-4 °F - 140 °F) Humidity [Operating humidity] 20% - 90% R.H. (wet bulb temperature ≤ 39 °C (102 °F), no condensation) [Storage humidity] 10% - 90% R.H.
Dimensions (Width) × (Height) × (Depth) Chassis mount type 313 mm (12.3 inch) × 243 mm (9.6 inch) × 46 mm (1.81 inch) (excluding the projection) Panel mount type 325 mm (12.8 inch) × 276 mm (10.9 inch) × 46 mm (1.81 inch) (excluding the projection) Mass Chassis mount type Approx. 2.5 kg (5.5 lbs.) Panel mount type Approx. 3.1 kg (6.8 lbs.
5-2. Glossary Afterimage The Afterimage is particular to LCD monitors. When the monitor screen is left on for a long period without use. The Afterimage can be removed gradually by changing the displayed image. Clock The analog input monitor needs to reproduce a clock of the same frequency as the dot clock of the graphics system in use, when the analog input signal is converted to a digital signal for image display. This is called clock adjustment.
5-3. Preset Timing The following table shows the factory preset video timing of the PC. ATTENTION • Display position may be deviated depending on the PC connected, which may require screen adjustment using Setting menu. • If a signal other than those listed in the table is input, adjust the screen using the Setting menu. However, screen display may still be incorrect even after the adjustment.
LIMITED WARRANTY EIZO NANAO CORPORATION (hereinafter referred to as “EIZO”) and distributors authorized by EIZO (hereinafter referred to as the “Distributors”) warrant, subject to and in accordance with the terms of this limited warranty (hereinafter referred to as the “Warranty”), to the original purchaser (hereinafter referred to as the “Original Purchaser”) who purchased the product specified in this document (hereinafter referred to as the “Product”) from EIZO or Distributors, that EIZO and Distributors
(For Japanese Market Only.) この保証書は所定事項を記入して効力を発するものですから、必ずお買い上げ年月日・販売店・住所・電話番号の 記入をご確認ください。 保証規定 1. 本製品の取扱説明書、本体添付ラベルなどの注意書に従った使用状態で保証期間内に故障した場合、無料にて 故障箇所の修理または交換をさせていただきますので、保証書を添えてお買い上げの販売店またはエイゾー サポートまで お申しつけください。 2.
