Important Please read this User’s Manual, and the Setup Manual (separate volume) carefully to familiarize yourself with safe and effective usage. • Please refer to the Setup Manual for basic information ranging from connection of the monitor to a PC to using the monitor. • The latest User’s Manual is available for download from our web site: http://www.eizo.
This product has been adjusted specifically for use in the region to which it was originally shipped. If operated outside this region, the product may not perform as stated in the specifications. No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
Notice for this monitor This product is suitable for displaying satellite images. This product has been adjusted specifically for use in the region to which it was originally shipped. If the product is used outside the region, it may not operate as specified in the specifications. This product may not be covered by warranty for uses other than those described in this manual.
Cleaning Attention • Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet or panel, and also quality deterioration of the image. • Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel. If necessary, the stains on the cabinet and panel surface can be removed by moistening part of a soft cloth with water. To use the monitor comfortably • An excessively dark or bright screen may affect your eyes.
CONTENTS Cover....................................................................... 1 Chapter 4 Notice for this monitor.......................................... 3 4-1. Setting Power Save...................................... 22 Cleaning..................................................................... 4 4-2. Enabling/Disabling Automatic Brightness Adjustment............................... 23 4-3. Adjusting the Brightness of Indicator....... 23 4-4. Setting DisplayPort Power Save............
Chapter 1 Introduction 1-1. Features • • • • 23.5″ wide format LCD Supports a resolution of 1920 × 1080. VA panel with 176˚ horizontal and vertical viewing angles 240 Hz panel drive Afterimages can be reduced by converting 120 Hz input signals into 240 Hz. • Supports 120 Hz signal input. -- Horizontal scan frequency: 26 - 140 kHz -- Vertical scan frequency: 59.0 - 122.0 Hz • Frame synchronization mode supported (59.0 - 61.0 Hz, 118.0 - 122.
1-3. Basic Operations and Functions ●●Basic Adjustment menu operations 1. Displaying Adjustment Menu 1. Press . The Adjustment menu appears. Menu title Current mode Item Setting Menu 2. Adjusting/Setting 1. Choose a menu to adjust/set with , , and then press . 2. Choose an item to adjust/set with , , and then press . 3. Adjust/set the selected item with , , and then press . 3. Exiting the software 1. Press a few times. The Adjustment menu finishes.
●●Showing Button Guide When you press the front buttons (except the button), the button guide appears next to the button. Button Guide Control button Note • The button guide will continue to appear while the Adjustment menu or Mode menu is showing. • The button guide is displayed differently depending on the selected menu or status.
●●Functions The following table shows the menus for adjustment and setting items of each menu. Main Menu Color*1 Item Reference “2-2. Adjusting Color” (page 11) Brightness Temperature Gamma Advanced Settings Hue Saturation Outline Enhancer Blur Reduction Gain Black Level 6 Colors Color Reset “3-7. Reset to default” (page 21) Screen Screen Size “2-3. Selecting Screen Size” (page 18) Power Manager Power Save “4-1. Setting Power Save” (page 22) Auto EcoView “4-2.
Chapter 2 Adjusting Screens 2-1. Setting the Resolution When you connect the monitor to the PC and find that the resolution is improper, or when you want to change the resolution, follow the procedure below. ●●Windows 8 / Windows 7 1. For Windows 8, click the “Desktop” tile on the Start Screen to display the desktop. 2. Right-click the mouse anywhere on the desktop except for icons. 3. From the displayed menu, click “Screen resolution”. 4. On the “Screen Resolution” dialog box, select the monitor. 5.
2-2. Adjusting Color ●●To select the display mode (Color Mode) This function allows easy selection of a desired mode according to monitor application. Display Modes Mode Purpose 1-User1 Available for the color settings according to your preference. 2-User2 3-User3 4-Paper Produces a printed paper effect by decreasing contrast and color temperature. The mode menu appears. 1-User1←→2-User2←→3-User3←→4-Paper Procedure 1. Press . The mode menu appears at the bottom left of the screen. 2.
●●To perform advanced adjustments “Color” of the Adjustment menu allows you to configure and save a separate set of color settings for each mode. Attention • It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more after the monitor power has been turned on, and then adjust the monitor. • The same image may be seen in different colors on multiple monitors due to their monitor-specific characteristics.
●●Adjusting Brightness The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD back panel). Setting Range 0 % to 100 % Procedure 1. Press or . The Brightness menu appears. 2. Use or for adjustment. to exit. 3. Press Attention • The brightness of the screen changes depending on the setting of “Blur Reduction” (see “Reducing motion blur “Blur Reduction”” (page 15)).
●●Adjusting Gamma Gamma can be adjusted. The brightness of the monitor varies depending on the input signal, however, the variation rate is not proportional to the input signal. To keep the balance between the input signal and the brightness of the monitor is called as “Gamma correction”. Setting Range 1.6-2.7, EPD Procedure . 1. Choose “Color” from the Adjustment menu, and press 2. Choose “Gamma” from “Color”, and press 3. Use or . for adjustment. to exit. 4.
●●To enhance outline of image OutlineEnhancer functions to emphasize outline of the images by emphasizing the color difference between pixels composing the images. This may improve the texture of the material and its feel of the images. On the contrary, it also functions to reproduce the images smoothly by gradating its outline. Procedure . 1. Choose “Color” from the Adjustment menu, and press 2. Choose “Advanced Settings” from “Color”, and press . . 3. Choose “Outline Enhancer”, and press 4.
●●Adjusting Gain The brightness of each color component red, green, and blue is called Gain. You can change the hue of “white” by adjusting gain. Setting Range 0 % to 100 % Procedure . 1. Choose “Color” from the Adjustment menu, and press 2. Choose “Advanced Settings” from “Color”, and press 3. Choose “Gain”, and press . . 4. Choose the color for adjustment from “Red”, “Green”, and “Blue”, and press 5. Use or . for adjustment. to exit. 6.
●●Adjusting 6 Colors The hue and saturation can be adjusted for each of six colors: Magenta, Red, Yellow, Green, Cyan, and Blue. Adjustable Range -100 to 100 Procedure . 1. Choose “Color” from the Adjustment menu, and press 2. Choose “Advanced Settings” from “Color”, and press 3. Choose “6 Colors”, and press . . 4. Choose the color for adjustment from “Magenta”, “Red”, “Yellow”, “Green”, “Cyan”, and “Blue”, and press . 5. Select “Hue” or “Saturation”, and press 6. Use 7. Press or . for adjustment.
2-3. Selecting Screen Size The image with the resolution other than the recommended resolution is displayed in full screen automatically. You can change the screen size by using the “Screen Size” function from “Screen”. Settings Function Full Displays an image in full screen. Images are distorted in some cases because the vertical rate is not equal to the horizontal rate. Enlarged Displays an image in full screen.
Chapter 3 Setting Monitor 3-1. Enabling/Disabling Mode Selection This function selects / deselects modes that should be skipped. Please use this function if you would like to prevent a mode from being used. Procedure . 1. Choose “Tools” from the Adjustment menu, and press 2. Choose “Mode Preset” from “Tools”, and press 3. Use or to select the mode to change, and press 4. Select “On” or “Off” with 5. Press . . or . to exit. Attention • You cannot set all the modes disable.
3-4. Changing Adjustment Menu Display Position You can change the display position of the Adjustment menu. Procedure . 1. Choose “Menu Settings” from the Adjustment menu, and press . 2. Choose “Menu Position” from “Menu Settings”, and press 3. Choose the position with or . to exit. 4. Press 3-5. Showing and Hiding the EIZO Logo Procedure 1. Press to turn off the monitor. down, press 2. Holding for at least two seconds to turn on the monitor. The “Optional Settings” menu appears. 3.
3-7. Reset to default The setting values are reset to the default settings. Attention • After resetting, you cannot undo the operation. Note • Regarding the default setting, see “Main Default Settings” (page 34). ●●To reset the color adjustments This function only resets the color adjustments for the currently selected mode to the default settings. Procedure . 1. Choose “Color” from the Adjustment menu, and press . 2. Choose “Color Reset” from “Color”, and press 3. Select “Execute” with 4. Press or .
Chapter 4 Power Saving Functions 4-1. Setting Power Save This function allows you to set the monitor into the power saving mode according to the PC status. When the monitor has shifted to the power saving mode, the images on the screen are not displayed. Attention • Turning off the main power switch or unplugging the power cord completely shuts off power supply to the monitor.
4-2. Enabling/Disabling Automatic Brightness Adjustment The ambient light sensor on the front side of the monitor detects the environmental brightness to adjust the screen brightness automatically and comfortably by using the Auto EcoView function. Attention • Be careful not to block the ambient light sensor on the lower side of the monitor when using the Auto EcoView function. Procedure . 1. Choose “PowerManager” from the Adjustment menu, and press . 2.
Chapter 5 Troubleshooting If a problem still remains after applying the suggested remedies, contact your local EIZO representative. 5-1. No picture Problem 1. No picture • Power indicator does not light. • Power indicator is lighting blue. • Power indicator is lighting orange. • Power indicator is flashing orange and blue. 2. The message below appears. • • • • Check whether the power cord is connected properly. Turn the main power switch on. Press .
5-2. Imaging problems Problem Possible cause and remedy 1. The screen is too bright or too dark. • Use “Brightness” in the Adjustment menu to adjust it. (The LCD monitor backlight has a limited life span.) When the screen becomes dark or begins to flicker, contact your local EIZO representative.) • Check the setting for “Blur Reduction” in the Adjustment menu. The brightness of the screen changes depending on the setting (see “Reducing motion blur “Blur Reduction”” (page 15)). 2. Characters are blurred.
5-3. Other problems Problem 26 Possible cause and remedy 1. The adjustment menu does not appear. • Check whether the operation lock function works (see “3-6. Locking Operation Buttons” (page 20)). 2. No mode menu is displayed. • Check whether the operation lock function works (see “3-6. Locking Operation Buttons” (page 20)). 3. The monitor connected with the USB cable is not detected. / USB devices connected to the monitor do not work. • Check whether the USB cable is connected correctly (see “6-3.
Chapter 6 Reference 6-1. Attaching the Optional Arm An optional arm (or an optional stand) can be attached by removing the stand section. Please refer to our web site for the corresponding optional arm (or optional stand). http://www.eizo.com Attention • When attaching an arm or stand, follow the instructions of their User’s Manual. • When using another manufacturer’s arm or stand, confirm the following in advance and select one conforming to the VESA standard.
6-2. Connecting Multiple External Devices The product has multiple connections to external devices and allows you to switch to one of the connections for display.
●●To switch among input signals The input signal switches each time is pressed. When the signal is switched, the active input port name appears at the top right corner of the screen. ●●To set input signal selection “Input Selection” Settings Function Auto The monitor recognizes the connector through which signals are input. When an external device enters the power saving mode, the monitor automatically displays another signal.
6-3. Making Use of USB (Universal Serial Bus) This monitor has a USB hub. It works as a USB hub when connected to a USB-compatible PC, allowing the connection of peripheral USB devices. ●●System Requirement • A PC equipped with a USB port. • Windows 8 / Windows 7 / Windows Vista / Windows XP / Windows 2000 or Mac OS X 10.2 or later and Mac OS 9.2.2 • USB cable (MD-C93) Attention • This monitor may not work depending on PC, OS or peripheral devices.
6-4. Displaying 3D Images This monitor supports stereo signal output in conformance with VESA standards. 3D images can be displayed by meeting the following conditions. ●●Conditions • 3D image signals (frame sequential format, vertical scan frequency 120 Hz) are being input. • Prepare 3D glasses and an IR emitter supported by the monitor. For information on supported products, refer to our web site. http://www.eizo.
6-5. Showing Monitor Information ●●Displaying signal information “Signal Info” This function displays the information about the current input signals displayed. Procedure . 1. Choose “Tools” from the Adjustment menu, and press 2. Choose “Signal Info” from “Tools”, and press . The “Signal Info” appears. (Example) ●●Displaying Monitor Information “Monitor Info” This function displays the information about the monitor. Procedure . 1. Choose “Tools” from the Adjustment menu, and press 2.
6-6. Specifications LCD Panel Size 23.5 inch (600 mm) Type Color TFT, VA Surface treatment Anti-Glare Surface hardness 3H Viewing angles Horizontal 176˚, vertical 176˚ (CR≥10) Dot pitch 0.2715 mm Response time Approx. 4 ms Max. dot clock 290 MHz Horizontal scan frequency 26 kHz - 140 kHz Vertical scan frequency 59.0 Hz - 122.0 Hz (non-interlace) (VGA TEXT: 69 Hz -71 Hz) Frame Synchronous mode 59.0 Hz - 61.0 Hz, 118.0 Hz - 122.0 Hz Resolution 1920 dots × 1080 lines Max.
USB Standard USB Specification Revision 2.0 Port Upstream port × 1, Downstream port × 2 Communication Speed 480 Mbps (high), 12 Mbps (full), 1.5 Mbps (low) Supply current Downstream: Max.
Chapter 7 Glossary DisplayPort DisplayPort is a next-generation digital AV interface that allows connection of the PC, audio, imaging devices, etc. to the monitor. One cable can transfer sound with images. DVI (Digital Visual Interface) DVI is a digital interface standard. DVI allows direct transmission of the PC’s digital data without loss. This adopts the TMDS transmission system and DVI connectors. There are two types of DVI connectors. One is a DVI-D connector for digital signal input only.
Overdrive This technology enhances response speed by increasing the potential difference at the time of motion of liquid-crystal pixels, and it is used for liquid-crystal TV sets and others in general. It provides clear-cut three-dimensional display with little afterimage, by improving response speed of the intermediate graduation range that frequently appears in moving images. Resolution The LCD panel consists of numerous pixels of specified size, which are illuminated to form images.
Appendix Trademark The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing, LLC in the United States and other countries. The DisplayPort Compliance Logo and VESA are registered trademarks of the Video Electronics Standards Association. Acrobat, Adobe, Adobe AIR, and Photoshop are registered trademarks of Adobe Systems Incorporated in the United States and other countries.
FCC Declaration of Conformity For U.S.A. , Canada, etc. (rated 100-120 Vac) Only FCC Declaration of Conformity We, the Responsible Party EIZOInc. 5710WarlandDrive,Cypress,CA90630 Phone:(562)431-5011 declare that the product Tradename:EIZO Model:DuraVisonFDF2405W is in conformity with Part 15 of the FCC Rules.
Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor Dieser Monitor ist für Bildschirmarbeitsplätze vorgesehen. Wenn nicht der zum Standardzubehör gehörige Schwenkarm verwendet wird, muss statt dessen ein geeigneter anderer Schwenkarm installiert werden.
LIMITED WARRANTY LIMITED WARRANTY EIZOCorporation(hereinafterreferredtoas“EIZO”)anddistributorsauthorizedbyEIZO(hereinafterreferredtoasthe “Distributors”)warrant,subjecttoandinaccordancewiththetermsofthislimitedwarranty(hereinafterreferredtoasthe “Warranty”),totheoriginalpurchaser(hereinafterreferredtoasthe“OriginalPurchaser”)whopurchasedtheproduct specifiedinthisdocument(hereinafterreferredtoasthe“Product”)fromEIZOorDistributors,thatEIZOa
BEGRENZTE GARANTIE EIZO Corporation (im Weiteren als „EIZO“ bezeichnet) und die Vertragsimporteure von EIZO (im Weiteren als „Vertrieb(e)“bezeichnet)garantierendemursprünglichenKäufer(imWeiterenals„Erstkäufer“bezeichnet),derdasin diesemDokumentvorgegebeneProdukt(imWeiterenals„Produkt“bezeichnet)vonEIZOodereinemVertrieberworben hat,gemäßdenBedingungendieserbeschränktenGarantie(imWeiterenals„Garantie“bezeichnet),dassEIZOund derVertriebnacheigenemE
GARANTIE LIMITÉE EIZO Corporation (ci-après dénommé « EIZO ») et les distributeurs autorisés par EIZO (ci-après dénommés «Distributeurs »),sousréserveetconformémentauxtermesdecettegarantielimitée(ci-aprèsdénommée«Garantie »),garantissentàl’acheteurinitial(ci-aprèsdénommé«Acheteur initial »)duproduitspécifiédanslaprésente(ci-après dénommé«Produit »)achetéauprèsd’EIZOoudeDistributeursagréésEIZO,queEIZOetsesDistributeursauront pouroptionderépare
GARANTÍA LIMITADA EIZO Corporation (en lo sucesivo “EIZO”) y sus distribuidores autorizados (en lo sucesivo los “Distribuidores”), conarregloydeconformidadconlostérminosdeestagarantíalimitada(enlosucesivola“Garantía”),garantizanal compradororiginal(enlosucesivoel“Comprador original”)quecompróelproductoespecificadoenestedocumento(en losucesivoel“Producto”)aEIZOoasusDistribuidores,queEIZOysusDistribuidores,asupropiocriterio,repararán osus
GARANZIA LIMITATA EIZOCorporation(acuisifaràriferimentodaquiinpoicon“EIZO”)ediDistributoriautorizzatidaEIZO(acuisifarà riferimento da qui in poi con “Distributori”) garantiscono, secondo i termini di questa garanzia limitata (a cui si farà riferimentodaquiinpoicon“Garanzia”)all’acquirenteoriginale(acuisifaràriferimentodaquiinpoicon“Acquirente originale”) che ha acquistato il prodotto specificato in questo documento (a cui si farà rif
BEGRÄNSAD GARANTI EIZOCorporation(nedankallat“EIZO”)ochEIZOsauktoriseradedistributörer(nedankallade“Distributörer”)garanterar ienlighetmedvillkorenidennabegränsadegaranti(nedankallad“Garantin”)denursprungligeköparen(nedankallad den“Ursprunglige köparen”)somköptedenidokumentetspecificeradeprodukten(nedankallad“Produkten”)från EIZOellerDistributörer,attEIZOellerDistributörerenligtegetgottfinnandekostnadsfrittantingenrepareraellerbytaut dendefektaPr
ΠΕΡΙΟΡΙΣΜΕΝΗ ΕΓΓΥΗΣΗ Η EIZO Corporation (στο εξής «EIZO») και οι διανομείς που εξουσιοδοτεί η EIZO (στο εξής «Διανομείς») παρέχουν εγγύηση, υποκείμενη και σύμφωνα με τους όρους της παρούσας περιορισμένης εγγύησης (στο εξής «Εγγύηση»),στοναρχικόαγοραστή(στοεξής«Αρχικός Αγοραστής»)οοποίοςαγόρασετοπροϊόνπουκαθορίζεταιστο παρόνέγγραφο(στοεξής«Προϊόν»)απότηνEIZOήτουςΔιανομείς,ηοποίαεξασφαλίζειότιηEIZOκαιοιΔιανομείς, σύμφωναμετηδιακριτήευχέρειάτ
ОГРАНИЧЕННАЯ ГАРАНТИЯ EIZO Corporation (называемая в дальнейшем “EIZO”) и авторизированные EIZO дистрибуторы (называемые в дальнейшем“Дистрибуторы”)гарантируют,всоответствиисусловиямиипунктамиэтойограниченнойгарантии (называемойвдальнейшем“Гарантия”),первичномупокупателю(называемомувдальнейшем“Первоначальный покупатель”),которыйприобрелуEIZOилиДистрибуторовпродукт,указанныйвэтомдокументе(называемый в дальнейшем “Продукт”), что EIZO или Дистрибуторы на св
有限责任保证书 EIZOCorporation（以下简称 EIZO ）和 EIZO 授权的经销商（以下简称 经销商 ），接受并依照本有限责任保证书（以 下简称 保证书 ）之条款，向从 EIZO 和经销商购买本文中所规定产品（以下简称 产品 ）的原买方（以下称 原买方 ） 提供保证 ：在保证期内（规定如下），如果原买方发现按本产品所附使用说明书（以下简称 用户手册 ）所述方式正常使 用本产品过程中，本产品出现故障或损坏，EIZO 和经销商根据其独自的判断免费修理或更换该产品。 本保证期限定为本产品自购买本产品之日起的二（2）年（以下简称 保证期限 ）。EIZO 和经销商将不向原买方或任何第 三方承担本保证书所规定之外的与本产品有关任何责任或义务。 本产品的任何部件停产七（7）年后，EIZO 和经销商将不再保留或保管任何这类部件。维修显示器时，EIZO 与经销商将 使用符合我方质量控制标准的替换零件。 本保证书仅对于设有经销商的国家或地区有效。本保证书并不限定原买方的任何法律权利。 无论本保证书的任何其他条款如何规定，对于任何下列情况之一，EIZO 和经销商将不承担本保证书规定责任 ： (a) 由于运输损害、
Recycling Information Recycling Information This product, when disposed of, is supposed to be collected and recycled according to your country’s legislationtoreduceenvironmentalburden.Whenyoudisposeofthisproduct,pleasecontactadistributoror anaffiliateinyourcountry. ThecontactaddresseesarelistedontheEIZOwebsitebelow. http://www.eizo.com ForrecyclinginformationforcustomersinSwitzerland,pleaserefertothefollowingwebsite. http://www.swico.
Πληροφορίες ανακύκλωσης Τοπροϊόναυτό,όταναπορρίπτεται,πρέπεινασυλλέγεταικαιναανακυκλώνεταισύμφωναμετηνομοθεσία τηςχώραςσαςέτσιώστεναμηνεπιβαρύνειτοπεριβάλλον.Γιανααπορρίψετετοπροϊόν,επικοινωνήστεμε έναναντιπρόσωποήμιαθυγατρικήεταιρείαστηχώρασας. ΟιδιευθύνσειςεπικοινωνίαςαναγράφονταιστηντοποθεσίαwebτηςEIZOπαρακάτω. http://www.eizo.
Informace o recyklaci Při likvidaci produktu musí být produkt vyzvednut a recyklován podle zákonů příslušné země, aby nedocházelo k zatěžování životního prostředí. Zbavujete-li se produktu, kontaktujte distributora nebo pobočkuvesvézemi.KontaktníadresyjsouuvedenynanásledujícíwebovéstráncespolečnostiEIZO. http://www.eizo.com Ringlussevõtu alane teave Keskkonnakoormusevähendamisekstulekskasutatudtootedkokkukogudajavõttaringlussevastavaltteie riigiseadustele.
Информация относно рециклиране Приизхвърлянетонатозипродуктсепредлагасъбиранетоирециклиранетомусъобразнозаконитена вашатастраназадасенамализамърсяванетонаоколнатасреда.Когатоискатедасеосвободитеот тозипродукт,молясвържетесестърговскиямупредставителилисъссъответнитеорганиотговарящи затовавъввашатастрана. ДаннитезавръзкаснассаописанинаследнияИнтернетсайтнаEIZO: http://www.eizo.
China Measures for RoHS Compliance in ChinaRoHS 关于电子信息产品污染控制标识 本标识根据「电子信息产品污染控制管理办法」，适用于在中华人民共和国销售的电子信息产品。标识中央的 数字为环保使用期限的年数。只要您遵守该产品相关的安全及使用注意事项，在自制造日起算的年限内，不会 产生对环境污染或人体及财产的影响。上述标识粘贴在机器背面。 • 有毒有害物质或元素的名称及含量 部件名称 有毒有害物质或元素 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 （Pb） （Hg） （Cd） （Cr（VI）） （PBB） （PBDE） 印刷电路板 × ○ ○ ○ ○ ○ 机箱 ○ ○ ○ ○ ○ ○ 液晶显示器 × ○ ○ ○ ○ ○ 其他 × ○ ○ ○ ○ ○ ○ ：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 规定的限量要求以下。 × ：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 规定的限量要求。 ( 企业可在此处 , 根据实际情況对上表中打“×”的技术原因进行进一步说明 ) Appendix
1st Edition-July, 2013 Copyright © 2013 EIZO Corporation All rights reserved. 03V24694A1 (U.
