Drawing : - TPC 436 Issue :-2 Date : - 24/11/16 DD400P INDUSTRIAL DEHUMIDIFIER OWNER’S MANUAL www.eipl.co.
Drawing : - TPC 436 Issue :-2 Date : - 24/11/16 UNPACKING Carefully remove the DD400P dehumidifier unit from its transit box and visually check for signs of transit damage. If there is evidence of damage DO NOT attempt to operate the unit, call your supplier for advice. Do not discard the packing, it will be useful when transporting the dehumidifier unit in the future. INTRODUCTION Dehumidifiers remove moisture from the air that is circulating through the unit.
Drawing : - TPC 436 Issue :-2 Date : - 24/11/16 SPECIFICATIONS MODEL: DD400P HEIGHT: 787mm WIDTH: 552mm DEPTH: 487mm WEIGHT: 31 Kg DRY AIRFLOW: 370 M³/HR WET AIRFLOW: 150 M³/HR POWER SUPPLY: 230V, 1 ph, 50Hz POWER 2.
Drawing : - TPC 436 Issue :-2 Date : - 24/11/16 INSTALLATION POSITIONING: The DD400P is designed for indoor use. Position the dehumidifier unit in the center of the room to be conditioned if at all possible. NOTE: Both the air inlets and outlets of the dehumidifier unit must have clear space around them and not be obstructed in anyway. For correct installation and operation the unit inlet and outlet must have a clearance of 0.5M from all adjacent surfaces and or structures.
Drawing : - TPC 436 Issue :-2 Date : - 24/11/16 OPERATION The electrical controls are located on the front of the rear. They are: ON / OFF Switch • • 0 Dehumidifier OFF I Dehumidifier ON Digital Humidistat Setting the Digital Humidistat The Digital Humidistat is factory preset to give the optimum level of control. Only adjustment of the desired set point is required. During normal operation, the display shows the current % Relative Humidity within the space being conditioned.
Drawing : - TPC 436 Issue :-2 Date : - 24/11/16 AIR MOVING SYSTEM: The DD400P is a dual fan system with dedicated fans for the “Process” air and “Regeneration” air flows. As the air passes over the rotor, it will be heated as a result of the regeneration cycle. The air leaving the unit will be hotter than the air entering During normal operation some parts of the dehumidifier may become hot. This is normal.
Drawing : - TPC 436 Issue :-2 Date : - 24/11/16 SAFETY -WARNING♦ DO NOT ALLOW CHILDREN TO PLAY WITH OR AROUND THE UNIT. ENSURE THE UNIT IS INACCESIBLE TO CHILDREN WHEN NOT ATTENDED.
Drawing : - TPC 436 Issue :-2 Date : - 24/11/16 ROUTINE SERVICE & REPAIR WARNING: ENSURE THAT THE POWER CORD TO THE MACHINE HAS BEEN DISCONNECTED BEFORE CARRYING OUT ROUTINE SERVICE. THE SERVICING AND REPAIR OF THIS UNIT SHOULD ONLY BE CARRIED OUT BY A SUITABLY QUALIFIED PERSON.
Drawing : - TPC 436 Issue :-2 Date : - 24/11/16 IF ANY OF THE PRECEDING PROBLEMS OCCUR, CONTACT THE EBAC INDUSTRIAL PRODUCTS LTD SERVICE CENTER PRIOR TO CONTINUED OPERATION OF THE UNIT TO PREVENT PERMANENT DAMAGE.
Drawing : - TPC 436 Issue :-2 Date : - 24/11/16 SPARE PARTS LIST DESCRIPTION PART NUMBER Process Air Fan Motor 3040251 Capacitor for Process Air Fan Motor 3030835 Process Inlet Filter 2050029 Regeneration Air Fan Motor 3040250 Capacitor for Regeneration Air Fan Motor 3030834 Regeneration Inlet Filter 2064032 Drive Motor 3040249 Capacitor for Drive Motor 3030832 Pulley 3050552 Pulley Belt 3050551 PTC Heater 3031625 Overheat Protector 3477026 Desiccant Wheel 3020706 PCB Controller
Drawing : - TPC 436 Issue :-2 Date : - 24/11/16 WARNINGS This appliance can be used by children from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the application in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
Drawing : - TPC 436 Issue :-2 Date : - 24/11/16 UK Head Office American Sales Office German Sales Office Ebac Industrial Products Ltd St Helens Trading Estate Bishop Auckland County Durham DL14 9AD Ebac Industrial Products Inc 700 Thimble Shoals Blvd. Suite 109, Newport News Virginia, 23606-2575 USA Ebac Industrial Products Ltd. Gartenfelder Str.
