Brochure

ManualsBrandsEIPL ManualsCooling & Air QualityDesiccant Dehumidifier

SPECIFICATIONS 10502SS-US

Height 13.3” (340 mm)

Width 13” (330 mm)

Depth 15” (380 mm)

Weight 37.5 lbs (17 kg)

Voltage 110 V

Current 7.5 A

Phase 1

Frequency 60 Hz

Power 0.8 kW

Process Airﬂow – Dry Air 115 cfm (196 m3/hr)

Regen Airﬂow – Wet Air 38 cfm (64 m3/hr)

Process Duct Size – Dry Air 5” (130 mm)

Regen Duct Size – Wet Air 2.75” (70 mm)

Rotor Wheel Speed (rph) 20

Noise Level 67 dba

Typical Extraction @ 27°C 60% 36 ppd (17 lt/day)

Min Operating Temperature -4 °F (-20°C)

Max Operating Temperature 104 °F (40°C)

FEATURES 10502SS-US

On/Off Control

Ammeter

Electronic Controls

Manual / Automatic Mode

Selection

Remote Humidity Sensor Facility

Hours Run Meter

Fitted Mains Plug

Fan Speeds 1

High Capacity PTC Heater

Process / Regen Air Filter

Rubber Anti-Vibration Feet

Single, Air Inlet Design

Free Standing

Humidistat O

Carrying Handles

Stainless Steel Construction

Inlet Duct Attachments O

High Temperature Safety Cut-outs

DD200 DESICCANT DEHUMIDIFIER

APPLICATION

Dehumidiﬁers are required wherever there is a need to lower the humidity level to prevent corrosion,

mold growth and condensation or maintain a low humidity condition during manufacture, packaging

or storing of hygroscopic products.

METHODS OF DEHUMIDIFICATION

Dehumidiﬁcation is possible using two possible principles, Condensation with refrigeration style

dehumidiﬁers and Adsorption with desiccant dehumidiﬁers.

Desiccant dehumidiﬁers perform exceptionally well when used in cooler climates, or when a low

dew-point, deep drying or low humidity levels are required. Since desiccant dehumidiﬁers do not

produce water, they will work effectively down to sub zero temperatures.

Their operation is simplistic yet extremely effective and reliable.

Air (Process Air) is drawn into the dehumidiﬁer, where is passes over a wheel impregnated with

Silica Gel. As the air passes over this wheel, any moisture present in the air, is absorbed into the

Silica Gel wheel before leaving the dehumidiﬁer as warm dry air.

The Silica Gel wheel is continually, slowly rotating,

typically at three revolutions per hour. As the

wheel rotates a small portion passes through the

regeneration segment. During this phase a second

air stream (Regeneration Air) is heated to a high

temperature before passing over the wheel. Any

moisture present in the wheel is released into this

air stream, this hot wet air is then exhausted

outside the area being dried.

KEY DESIGN FEATURES

• Stainless Steel Construction

• Auto / Manual Mode Selection

• Electronic Controls

• High Capacity PTC Heater

• Remote Humidistat Facility

• Low Temperature Operation

• Ammeter

PHARMACEUTICAL, CONFECTIONARY, DEFENSE INDUSTRY,

WATER DAMAGE, COLD STORES, POWER STATIONS, PLASTICS

SPECIFICATIONS

Summary of content (2 pages)

PAGE 1
SPECIFICATIONS Height Width Depth Weight Voltage Current Phase Frequency Power Process Airflow – Dry Air Regen Airflow – Wet Air Process Duct Size – Dry Air Regen Duct Size – Wet Air Rotor Wheel Speed (rph) Noise Level Typical Extraction @ 27°C 60% Min Operating Temperature Max Operating Temperature 10502SS-US 13.3” (340 mm) 13” (330 mm) 15” (380 mm) 37.5 lbs (17 kg) 110 V 7.5 A 1 60 Hz 0.8 kW 115 cfm (196 m3/hr) 38 cfm (64 m3/hr) 5” (130 mm) 2.
PAGE 2
HOW A DEHUMIDIFIER WORKS Process air is drawn into the dehumidifier. Process air passes over a wheel impregnated with silica gel. The silica gel absorbs the moisture from the air. Process air leaves the dehumidifier as warm dry air. Applications Offices Shops Restaurants Warehouses Basements Factories De-Flooding Pharmaceutical Defense Industry Confectionary The silica gel wheel continually rotates. Silica gel releases the moisture from the wheel into the regeneration air.