Drawing : - TPC 392 Issue : - 12 Date : - 21/08/20 DD1200 10540GR-US – 220V / 3PH / 60HZ INDUSTRIAL DEHUMIDIFIER OWNER’S MANUAL www.eipl.co.
Drawing : - TPC 392 Issue : - 12 Date : - 21/08/20 DD1200 PACKAGE CONTENTS Item Description Quantity 10540GR-US Dehumidifier 1 TPC392 Manual 1
Drawing : - TPC 392 Issue : - 12 Date : - 21/08/20 UNPACKING Carefully remove the DD1200 dehumidifier unit from its transit box and visually check for signs of transit damage. If there is evidence of damage DO NOT attempt to operate the unit, call your supplier for advice. Do not discard the packing, it will be useful when transporting the dehumidifier unit in the future. INTRODUCTION Dehumidifiers remove moisture from the air that is circulating through the unit.
Drawing : - TPC 392 Issue : - 12 Date : - 21/08/20 SPECIFICATIONS MODEL: DD1200 HEIGHT: 1420mm (56”) WIDTH: 711mm (28”) DEPTH: 584mm (23”) WEIGHT: 100Kg (220.5lbs) POWER SUPPLY: 220V, 3 ph, 60Hz CURRENT: 31A (max) POWER 11.
Drawing : - TPC 392 Issue : - 12 Date : - 21/08/20 UNIT CAPACITY The ambient conditions of the area to be dehumidified will determine the amount of water extraction the unit is capable of. Measure the ambient conditions of the area to be determined and then use that information with the following capacity diagram to determine the unit capacity.
Drawing : - TPC 392 Issue : - 12 Date : - 21/08/20 INSTALLATION The DD1200 is designed for indoor use. The unit should be placed on a level surface and a space of 1 meter free around all faces to allow access for any duct work and servicing. Connecting duct work: The regeneration outlet must be ducted to outside the area being dehumidified. The outlet duct spigot is 6” diameter and only 6” ducting or greater should be attached. The process outlet can be ducted to a specific area or another room.
Drawing : - TPC 392 Issue : - 12 Date : - 21/08/20 Control Settings Once the unit is positioned correctly, required duct work attached and the power supply connected, the fan speeds and temperature control need to be set correctly. The fan speed controls are located behind a removable cover, to the right of the main controls. The controls are numbered 1 to 10, with 10 being the maximum speed. The temperature control regulates the temperature of the reactivation airflow onto the desiccant wheel.
Drawing : - TPC 392 Issue : - 12 Date : - 21/08/20 FAN PERFORMANCE CURVES For example: If the total system resistance is 600pa then the process fan selector would have to be set to No 10 to achieve the required airflow of 705cfm For example: If the total system resistance is 400pa then the regen fan selector would have to be set to No 8 to achieve the required airflow of 195cfm
Drawing : - TPC 392 Issue : - 12 Date : - 21/08/20 OPERATION The electrical controls are located on the front of the unit. They are: • On / Off Switch M Dehumidifier in continuous operation A Dehumidifier operation by means of an external humidistat 0 Dehumidifier OFF • An hour counter is provided to display the total time the unit has been in operation • DRYING lamp – unit is in drying mode. • HEATING lamp – indicates heating elements are on. Cycle on/off when in drying mode.
Drawing : - TPC 392 Issue : - 12 Date : - 21/08/20 SAFETY -WARNING♦ DO NOT ALLOW CHILDREN TO PLAY WITH OR AROUND THE UNIT. ENSURE THE UNIT IS INACCESIBLE TO CHILDREN WHEN NOT ATTENDED.
Drawing : - TPC 392 Issue : - 12 Date : - 21/08/20 ROUTINE SERVICE & REPAIR WARNING: ENSURE THAT THE POWER CORD TO THE MACHINE HAS BEEN DISCONNECTED BEFORE CARRYING OUT ROUTINE SERVICE. THE SERVICING AND REPAIR OF THIS UNIT SHOULD ONLY BE CARRIED OUT BY A SUITABLY QUALIFIED PERSON.
Drawing : - TPC 392 Issue : - 12 Date : - 21/08/20 IF ANY OF THE PRECEDING PROBLEMS OCCUR, CONTACT THE EBAC INDUSTRIAL PRODUCTS LTD SERVICE CENTER PRIOR TO CONTINUED OPERATION OF THE UNIT TO PREVENT PERMANENT DAMAGE.
Drawing : - TPC 392 Issue : - 12 Date : - 21/08/20 WARNINGS This appliance can be used by children from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the application in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
Drawing : - TPC 392 Issue : - 12 Date : - 21/08/20
Drawing : - TPC 392 Issue : - 12 Date : - 21/08/20
A B 6 290 PROCESS AIR OUTLET 580 n200 n150 MAINS INLET GLAND ELECTRICAL CONNECTIONS PANEL 40 POWER ISOLATOR 40 718 4 CONTROLS 4 65 5 HUMIDISTAT SENSOR WIRING GLAND 401.7 17 C REGENERATION AIR OUTLET 5 450 832 263 56 D 6 133 512 314 450 3 DO NOT SCALE IF IN DOUBT ASK 3RD ANGLE PROJECTION 1 9 97 3 1126.7 12/02/13 14/10/14 13/07/18 1 2 3 2 TITLE 2 MATERIAL DIMENSIONS IN m.m. TOLERANCES UNLESS OTHERWISE STATED 0. 1 FINISH 0.0 0.25 0.00 0.05 ANGULAR 0.
A 6 5 4 3 DO NOT SCALE IF IN DOUBT ASK 3RD ANGLE PROJECTION 1 9 97 13/07/18 3 2 MATERIAL DIMENSIONS IN m.m. TOLERANCES UNLESS OTHERWISE STATED 0. 1 FINISH 0.0 0.25 0.00 0.05 ANGULAR 0.5 DEGREE TITLE N/A N/A 1 1/14 SHEET 2 OF 4 W DAGLISH DD1200 DRG.NO. CAD SCALE : DRAWN : DD1200 - GENERAL ASSEBLY / OVERVIEW DIMENSIONS ADD3ED - WDA SHEET 4 ADDED - WDA ORIGINAL BIS HOP AUCKLAND Co. DURHAM ENGLAND 14/10/14 2 1 A B 12/02/13 1 2 COMMENTS B DATE ISS.
5 4 14/10/14 13/07/18 2 3 2 TITLE 1 DD1200 - GENERAL ASSEMBLY / OVERVIEW DIMENSIONS ADD3ED - WDA SHEET 4 ADDED - WDA ORIGINAL COMMENTS BIS HOP AUCKLAND Co. DURHAM ENGLAND 12/02/13 1 DETAIL A SCALE 1/3 DATE ISS. D A 3 DO NOT SCALE IF IN DOUBT ASK 3RD ANGLE PROJECTION 2 MATERIAL DIMENSIONS IN m.m. TOLERANCES UNLESS OTHERWISE STATED 0. 1 FINISH 0.0 0.25 0.00 0.05 ANGULAR 0.5 DEGREE N/A N/A 1 1/10 SHEET 3 OF 4 W DAGLISH DD1200 DRG.NO.
A B C D 6 6 5 491 5 263 20.5 75 300 173 45 33 450 328 21 45 74.5 40 4 404 314 234 301 450 492 4 3 DO NOT SCALE IF IN DOUBT ASK 3RD ANGLE PROJECTION 1 9 97 8 OFF M5 FIXINGS 8 OFF M5 FIXINGS 3 13/07/18 3 2 2 MATERIAL DIMENSIONS IN m.m. TOLERANCES UNLESS OTHERWISE STATED 0. 1 FINISH 0.0 0.25 0.00 0.05 ANGULAR 0.5 DEGREE TITLE 1 N/A N/A 1 1/7 SHEET 4 OF 4 W DAGLISH DD1200 DRG.NO.
Drawing : - TPC 392 Issue : - 12 Date : - 21/08/20 UK Head Office American Sales Office German Sales Office Ebac Industrial Products Ltd St Helens Trading Estate Bishop Auckland County Durham DL14 9AD Ebac Industrial Products Inc 700 Thimble Shoals Blvd. Suite 109, Newport News Virginia, 23606-2575 USA Ebac Industrial Products Ltd. Gartenfelder Str.
