TE-CD 18/50 Li-i BL GB Original operating instructions Cordless Hammer Drill/Screwdriver 7 Art.-Nr.: 45.139.49 (1x4.0 Ah) Anl_TE_CD_18_50_Li_i_BL_EX_UK_SPK7.indb 1 I.-Nr.: 21010 04.05.
1 1 11 3 9 4 10 2 8 6 2 7 5 3 1. 6 5 8 5 2. -2- Anl_TE_CD_18_50_Li_i_BL_EX_UK_SPK7.indb 2 04.05.
4 5 1 11 7 2 3 1 4 6 7 a 10 2 9 a -3- Anl_TE_CD_18_50_Li_i_BL_EX_UK_SPK7.indb 3 04.05.
-4- Anl_TE_CD_18_50_Li_i_BL_EX_UK_SPK7.indb 4 04.05.
GB Table of contents 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Safety regulations Layout and items supplied Proper use Technical data Before starting the equipment Operation Cleaning, maintenance and ordering of spare parts Disposal and recycling Storage Charger indicator -5- Anl_TE_CD_18_50_Li_i_BL_EX_UK_SPK7.indb 5 04.05.
GB Danger! - Read the operating instructions to reduce the risk of inquiry Caution! Wear ear-muffs. The impact of noise can cause damage to hearing. Caution! Wear a breathing mask. Dust which is injurious to health can be generated when working on wood and other materials. Never use the device to work on any materials containing asbestos! Caution! Wear safety goggles. Sparks generated during working or splinters, chips and dust emitted by the device can cause loss of sight.
GB Danger! When using the equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety regulations with due care. Keep this manual in a safe place, so that the information is available at all times. If you give the equipment to any other person, hand over these operating instructions and safety regulations as well.
GB 4. Technical data The stated vibration emission levels and stated noise emission values can also be used to make an initial assessment of exposure. Voltage supply ....................................... 18 V d.c. Idling speed: .......................... 0-500 / 0-1800 rpm Torque settings: ....................................... 20+1+1 Forward and reverse rotation ..........................yes Chuck clamping width ....................... max. 13 mm Battery charger output voltage: ............. 20 V d.
GB faultless condition. 3. Always check for concealed electric cables and gas and water pipes when drilling and screwing in walls. 6.2 Torque setting (Fig. 4 / Item 1) Important! The tool must be at a standstill when you set the torque with the setting ring. The cordless screwdriver is fitted with a mechanical torque selector. 6. Operation The torque for a specific size of screw is selected with the set-collar (1).
GB 6.6 Changing over from 1st gear to 2nd gear (Fig. 4 / Item 7) You can work at a higher or lower speed depending on the position of the selector switch. To avoid damaging the gear unit you should only change over gears when the tool has stopped. 6.7 Battery capacity indicator (Fig. 6 – Item 2) Press the battery capacity indicator switch (a). The battery capacity indicator (2) shows the charge status of the battery using 3 LEDs. All 3 LEDs are lit: The battery is fully charged.
GB 8. Disposal and recycling The equipment is supplied in packaging to prevent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. Never place defective equipment in your household refuse. The equipment should be taken to a suitable collection center for proper disposal.
GB 10. Charger indicator Indicator status Explanations and actions Red LED Green LED Off Flashing Ready for use The charger is connected to the mains and is ready for use; there is no battery pack in the charger On Off Charging The charger is charging the battery pack in quick charge mode. The charging times are shown directly on the charger. Important! The actual charging times may vary slightly from the stated charging times depending on the existing battery charge.
GB For EU countries only Never place any electric power tools in your household refuse. To comply with European Directive 2012/19/EU concerning old electric and electronic equipment and its implementation in national laws, old electric power tools have to be separated from other waste and disposed of in an environment-friendly fashion, e.g. by taking to a recycling depot.
GB Service information We have competent service partners in all countries named on the guarantee certificate whose contact details can also be found on the guarantee certificate. These partners will help you with all service requests such as repairs, spare and wearing part orders or the purchase of consumables. Please note that the following parts of this product are subject to normal or natural wear and that the following parts are therefore also required for use as consumables.
GB Warranty certificate Dear Customer, All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee card. You can also contact us by telephone using the service number shown. Please note the following terms under which guarantee claims can be made: 1. These guarantee terms apply to consumers only, i.e.
ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar D erklärt folgende Konformität gemäß EU-Richtlinie und Normen für Artikel GB explains the following conformity according to EU directives and norms for the following product F déclare la conformité suivante selon la directive CE et les normes concernant l’article I dichiara la seguente conformità secondo la direttiva UE e le norme per l’articolo NL verklaart de volgende overeenstemming conform EU richtlijn en normen voor het product E declara la siguiente con
- 17 - Anl_TE_CD_18_50_Li_i_BL_EX_UK_SPK7.indb 17 04.05.
EH 05/2020 (01) Anl_TE_CD_18_50_Li_i_BL_EX_UK_SPK7.indb 18 04.05.
