TE-CD 18/44 Li-i GB Original operating instructions Cordless Impact Drill 7 Art.-Nr.: 45.137.96 (1x1,5 Ah) Anl_TE_CD_18_44_Li_i_Kit_SPK7.indb 1 I.-Nr.: 21010 18.05.
-2- Anl_TE_CD_18_44_Li_i_Kit_SPK7.indb 2 18.05.
1 9 1 7 11 3 4 10 2 6 8 2 5 3 6 1. 5 8 5 2. -3- Anl_TE_CD_18_44_Li_i_Kit_SPK7.indb 3 18.05.
5 1 11 3 1 4 7 2 6 7 a 9 10 a 2 -4- Anl_TE_CD_18_44_Li_i_Kit_SPK7.indb 4 18.05.
GB Table of contents 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Safety regulations Layout and items supplied Proper use Technical data Before starting the equipment Operation Cleaning, maintenance and ordering of spare parts Disposal and recycling Storage Charger indicator -5- Anl_TE_CD_18_44_Li_i_Kit_SPK7.indb 5 18.05.
GB Danger! - Read the operating instructions to reduce the risk of inquiry Caution! Wear ear-muffs. The impact of noise can cause damage to hearing. Caution! Wear a breathing mask. Dust which is injurious to health can be generated when working on wood and other materials. Never use the device to work on any materials containing asbestos! Caution! Wear safety goggles. Sparks generated during working or splinters, chips and dust emitted by the device can cause loss of sight.
GB Danger! When using the equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety regulations with due care. Keep this manual in a safe place, so that the information is available at all times. If you give the equipment to any other person, hand over these operating instructions and safety regulations as well.
GB 4. Technical data The stated vibration emission levels and stated noise emission values can also be used to make an initial assessment of exposure. Voltage supply ........................................18 V d.c. Idling speed: ............................0-350/0-1250 rpm Torque settings: ....................................... 18+1+1 Forward and reverse rotation ..........................yes Chuck clamping width ....................... max. 13 mm Battery charger output voltage: ............. 21 V d.
GB 5. Before starting the equipment 6.2 Torque setting (Fig. 4 / Item 1) Important! The tool must be at a standstill when you set the torque with the setting ring. The cordless screwdriver is fitted with a mechanical torque selector. Be sure to read the following information before you use your cordless screwdriver for the first time: 1. Charge the battery pack with the charger supplied. An empty battery pack requires a charging period of approximately 0.5-1 hour. 2.
GB 6.5 On/Off switch (Fig. 5 / Item 4) Infinitely variable speed control is possible with the On/Off switch. The further you press the switch, the higher the speed of the battery-powered drill/screwdriver. 6.6 Changing over from 1st gear to 2nd gear (Fig. 4 / Item 7) You can work at a higher or lower speed depending on the position of the selector switch. To avoid damaging the gear unit you should only change over gears when the tool has stopped. 6.7 Battery capacity indicator (Fig.
GB 8. Disposal and recycling The equipment is supplied in packaging to prevent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. Never place defective equipment in your household refuse. The equipment should be taken to a suitable collection center for proper disposal.
GB 10. Charger indicator Indicator status Explanations and actions Red LED Green LED Off Flashing Ready for use The charger is connected to the mains and is ready for use; there is no battery pack in the charger On Off Charging The charger is charging the battery pack in quick charge mode. The charging times are shown directly on the charger. Important! The actual charging times may vary slightly from the stated charging times depending on the existing battery charge.
GB For EU countries only Never place any electric power tools in your household refuse. To comply with European Directive 2012/19/EU concerning old electric and electronic equipment and its implementation in national laws, old electric power tools have to be separated from other waste and disposed of in an environment-friendly fashion, e.g. by taking to a recycling depot.
GB Service information We have competent service partners in all countries named on the guarantee certificate whose contact details can also be found on the guarantee certificate. These partners will help you with all service requests such as repairs, spare and wearing part orders or the purchase of consumables. Please note that the following parts of this product are subject to normal or natural wear and that the following parts are therefore also required for use as consumables.
GB Warranty certificate Dear Customer, All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee card. You can also contact us by telephone using the service number shown. Please note the following terms under which guarantee claims can be made: 1. These guarantee terms apply to consumers only, i.e.
D Konformitätserklärung: Wir erklären Konformität gemäß EURichtlinie und Normen für Artikel Declaration of conformity: We declare conformity in accordance with the EU directive and standards for article F Déclaration de conformité : Nous déclarons la conformité conformément aux directives et normes UE pour l‘article I Dichiarazione di conformità: dichiariamo la conformità secondo la direttiva UE e le norme per l‘articolo DK Overensstemmelseserklæring: Vi attesterer overensstemmelse iht.
Declaration of conformity We, Einhell UK Ltd Champions Business Park, First Floor Unit 10, Arrowe Brook Rd, Upton, Wirral CH49 0AB, United Kingdom declare the conformity to UK standards and legislation was assessed for: Cordless Impact Drill TE-CD 18/44 Li-i (Einhell) UK legislation X Electromagnetic Compatibility Regulation Simple Pressure Vessels (Safety) Regulation Electrical Equipment (Safety) Regulation Measuring Instruments Regulation Radio Equipment Regulation Pressure Equipment (Safety) Regulati
- 18 - Anl_TE_CD_18_44_Li_i_Kit_SPK7.indb 18 18.05.
- 19 - Anl_TE_CD_18_44_Li_i_Kit_SPK7.indb 19 18.05.
- 20 - Anl_TE_CD_18_44_Li_i_Kit_SPK7.indb 20 18.05.
- 21 - Anl_TE_CD_18_44_Li_i_Kit_SPK7.indb 21 18.05.
EH 05/2021 (02) Anl_TE_CD_18_44_Li_i_Kit_SPK7.indb 22 18.05.
