Owner's Manual Network Set-up and Operation Wired and Wireless Setting Projector Controller Network Viewer Moderator Function Italiano First, read the owner's manual of the projector to understand the projector's basic operation and the safety instructions. The safety instructions in the owner's manuals should be followed. Deutsch Español Français English Note; For operating the projector via the Wireless network, USB Wireless LAN adapter (optionally available) is required.
Compliance Federal Communication Commission Notice Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Safety Instructions CAUTION IN USING THE PROJECTOR VIA NETWORKS ● When you find a problem with the projector, remove the power cable immediately and inspect the unit. Using the projector with failure may cause fire or other accidents. ● If you remotely use the projector via networks, carry out a safety check regularly and take particular care to its environment. Incorrect installation may cause fire or other accidents. CAUTION IN USING NETWORK FUNCTION ● EIKI Co., Ltd.
Table of Contents Compliance............................................................................................2 Safety Instructions ................................................................................3 Table of Contents..................................................................................4 Operating Environment and Configuration ........................................6 Required Operating Environment for Computers ......................................
Table of Contents Advanced Settings .....................................................................................46 TCP / IP................................................................................................................46 Wireless Setting ..................................................................................................47 E-mail...................................................................................................................48 Admin Password .......
Operating Environment and Configuration Required Operating Environment for Computers When operating the projector via the networks, computers should meet the operating environment below.
Operating Environment and Configuration Network Specifications of the Projector LAN Terminal Data communication speed Protocol 100Base-TX(100Mbps)/10Base-T(10Mbps) TCP/IP USB Wireless LAN Adapter (Optionally available. Model : WL-30) Interface Communication Mode Data Transfer Speed Wireless Frequency (Channel) Correspond to IEEE8021b/g, USB 2.0 / 1.1 AdHoc, Infrastructure 1/2/5.5/11Mbps(IEEE802.11b) 6/9/12/18/24/36/48/54Mbps(IEEE802.11g) When using AdHoc mode, only IEEE802.11b is usable.
Chapter 1 1. About LAN Functions English This chapter describes the features, the mechanism, and connection procedures of the LAN.
1. About LAN Functions LAN Functions and the Features This product is loaded with a LAN network function which enables you to project an image on the computer through a projector via Network with dedicated software. With the software, you can also manipulate the projecting image and the projector. This software has functions below and you can use the projector under various network environments to meet the wide-ranging needs of the operation. • Accept both Wired and Wireless LAN environment.
1. About LAN Functions An Example of the Connection The illustration below shows an example of the projection via the LAN. You can project the image on Computer (1) (Wired LAN connection), or Computer (2) (Wireless LAN connection) through the selected projector . 1.5 1.0 0.5 0.0 2.0 1.5 1.0 0.5 0.0 2.0 1.5 1.0 0.5 0.0 Computer (1) Access point Computer (2) English 2.
1. About LAN Functions LAN Connection Modes Connection modes differ depending on the LAN and computer environments. Connect appropriately for each environment. ■ Wireless LAN, Infrastructure Communication Mode Communicate over an access point between Wired LAN equipment and Wireless LAN equipment. Or, communicate over an access point among multiple Wireless LAN equipment. Wireless LAN equipment will select an access point to communicate SSID/ESSID modes.
1. About LAN Functions ■ Wired LAN Communication Mode Communicate via the LAN line. Computer(1) Computer(2) Computer (3) English ✳ Operate the computer mouse with the remote control. When the projector's remote control employs mouse operating function, you can operate the computer by the remote control which is provided with the projector. Use the remote control pointing to the projector. You do not need to connect the USB cable to operate the computer mouse.
Chapter 2 2. Setup Procedures English This chapter describes how to install the NetworkModule software and how to set up the networks.
2. Setup Procedures To use the projector via the networks, follow the setup procedures below. STEP 1 Install the software on computers. Install the software recorded in CD-ROM on each computer which will be operated. Read following pages of this chapter to install. STEP 2 Select Wired LAN or Wireless LAN then connect the LAN and set the configuration. Decide depending on the LAN environment. Wired LAN .......Refer to "4. Wired LAN Configurations" (p25-31) Wireless LAN ...Refer to "5.
2. Setup Procedures Installing the Software Three pieces of software is recorded in the supplied CD-ROM. English 1. Insert the CD-ROM into the drive. The software will be activated automatically and "Software License" screen will be displayed. Read the license carefully and if you agree, check "Agree" then click "OK". When the screen is not displayed automatically, open "CD-ROM Drive" in "My computer" of your computer to activate "AutoRun. exe". The software can be displayed both in Japanese and English.
2. Setup Procedures ■ When projecting with the Moderator function. For details about Moderator function, refer to the "8. Use the Moderator Function". a Install "NetworkModule Client" into each client's (participants except for the moderator) computers. For installation, refer to"■ When projecting via a selected computer which is connected to the LAN". (p17) s Click (Select) "NetworkModule Moderator" on the left side of the screen. d Click "Install NetworkModule Moderator".
Chapter 3 3. Names and Functions of the Operation Screen. English This chapter describes the functions of each part of the operation screen.
3. Names and Functions of the Operation Screen Network Connection Standby Display Select projector input either "Wired" or "Wireless" and the Network connection standby display will appear. Network environment will be shown on the screen. With this screen, you can confirm that the network connection is whether "Wired" or "Wireless", or network environment of the projector when setting the connection. After selecting "Wired" or "Wireless", "Please wait...
3.Names and Functions of the Operation Screen NetworkModule Client This software is to project the computer screen via the networks. To use the moderator function, install this software into each participant's (except for the moderator) computers. Activate "NetworkModule Client" from the application start menu or the shortcut on the desk top, then following screen will appear. Then the program will start.
3.Names and Functions of the Operation Screen r Real time Capture button Capture (Project) the computer screen in real time. After capturing, the button will change into the Stop Capture button. Click the Stop Capture button, then the projection will stop and the screen will disappear. t One-shot Capture button Copy and capture (project) the computer screen without modification. After completing the image transmission, the communication will stop and you can operate other functions.
3.Names and Functions of the Operation Screen NetworkModule Moderator When using the moderator function, install the software on the moderator's computer. The function is the same as "NetworkModule Client" and on top of it, the moderator function is added. Activate "NetworkModule Moderator" from the application start menu or the shortcut on the desk top, then following screen will appear. Then the program will start.
Chapter 4 4. Wired LAN Configurations English This chapter describes the preparation for Wired LAN setting with projectors and how to set the LAN environment.
4. Wired LAN Configurations Setting procedures and contents differ depending on the LAN installation location. When installing, consult your system administrator to set up the LAN appropriately. Connecting to the LAN Line Connect the LAN cable to the LAN connection terminal of the projector. LAN Connection Terminal Access Lamp (Green) Blink green when exchanging data with the network. USB Link Lamp (Orange) Light orange when the terminal is correctly connected to the Network HUB with the LAN cable.
4. Wired LAN Configurations 4. Press the SELECT button. LAN setting screen will appear and selected LAN settings will be displayed. Adjust each item to the setting environment. Consult your system administrator about the detailed settings. Adjust the figures with the Point ed buttons and move among the items with the Point 7 8 buttons. 5. After completing all the settings, select "Set" and press the SELECT button. Now, all procedures has done.
4. Wired LAN Configurations Confirming the Operation Confirm that the projector has connected to the LAN properly. 1. Activate "NetworkModule Client" or "NetworkModule Moderator" which is installed into the computer connected to the LAN . 2. After appearing "NetworkModule searching" message, the name of the projector* appears on the Network Projector List, then the network setting has completed properly.
4. Wired LAN Configurations When set up the projector where separated by the router and the segment is different; Projector will not be found nor displayed. In this case, the projector needs to be searched directly by the IP address. 1. Click the Add NetworkModule button in the Advanced Settings menu. The Add NetworkModule screen will appear. 2. Click "Add" then the IP address screen will appear. Enter the IP address and click "OK". The projector will be added on the Add NetworkModule screen.
4. Wired LAN Configurations User PIN Code The User PIN code is to restrict the access from the networks to the projector. After setting the User PIN code, you need to enter it to operate the projector via the networks. 1. Select User PIN code, and press the SELECT button. The User PIN code screen will appear. 2. Set the User PIN code. Set the figures with the Point ed buttons and move to the next items with the Point 7 8buttons. Select "Set" and press the SELECT button to set.
4. Wired LAN Configurations Factory Default Setting of the Wired LAN SELECTED LAN LAN1 Parameter IP ADDRESS SUBNET MASK GATEWAY LAN2 LAN3 169.254.100.100 192.168.100.100 192.168.100.100 255.255.0.0 255.255.255.0 255.255.255.0 255.255.255.255 255.255.255.255 255.255.255.255 255.255.255.255 255.255.255.255 255.255.255.
Chapter 5 5. Wireless LAN Configurations English This chapter describes the preparation for Wireless LAN setting with projectors and how to set the LAN environment. To operate via Wireless LAN, attach the optionally available USB Wireless LAN Adapter (Model : WL30) to the projector. The setting procedures and configurations differ depending on the LAN installation location. Consult your system administrator for installation and set the LAN appropriately.
5. Wireless LAN Configurations Attaching the USB Wireless LAN Adapter Insert the USB Wireless LAN Adapter into the USB terminal of the projector. Inserting the adapter after verifying the shape of the connector in order not to break the terminal. CAUTION: Use specified USB Wireless LAN Adapter (Model : WL-30). If you use other product, the projector will not be operated properly. USB Lamp After the USB Wireless LAN Adapter becomes ready for use, the lamp will start to blink green when receiving data.
5. Wireless LAN Configurations 3. Press the Point button then "Please wait..." message will appear and switching operation will start. Switching will take a while and after completing the operation the message will disappear. During the switching period, the projector cannot be operated. Wireless setting User PIN code Wireless Information Wireless Factory Default English 4. Press the SELECT button. LAN setting screen will appear and the selected LAN settings will be displayed.
5. Wireless LAN Configurations Easy Setting With this setting, you do not need any complex LAN setting procedures. The LAN mode will be AdHoc IEEE802.11b. CAUTION: This function can be used only when logged in by Administrative right with Windows XP. Cannot be used with Windows98SE / Me, Windows2000. Windows XP should be Service Pack 1 or later version. Setting Procedures 1. Turn on the projector and select "Wireless" from the input menu of the projector. 2.
5. Wireless LAN Configurations Computer environment and Wireless LAN connection; Wireless LAN with Easy setting connection will be made via AdHoc IEEE802.11b mode. For setting contents, refer to "Wireless LAN factory default settings". (p38) With the Easy setting, computer's LAN environment setting will be switched to the settings on p38. Because of that, the LAN cannot work for the other operation while using "NetworkModule Client" or "NetworkModule Moderator".
5. Wireless LAN Configurations Wireless LAN Factory Default Settings Factory default settings for LAN4, LAN5, and SIMPLE as follows. Selected LAN Setting Items IP ADDRESS SUBNETMASK GATEWAY ADDRESS IP CONFIGURATION LAN4 LAN5 SIMPLE 169.254.100.100 192.168.100.100 169.254. * . * 255.255.0.0 255.255.255.0 255.255.0.0 255.255.255.255 255.255.255.255 255.255.255.255 MANUAL DHCP MANUAL ENABLE ENABLE ENABLE ENABLE ENABLE DISABLE 11 11 11 802.11b AdHoc INFRASTRUCTURE 802.
Chapter 6 6. Configurations with Browser The projector can be set, controlled and operated via the browser. English Caution: When operating the projector with the browser, connect the projector to the computer with Wired or Wireless LAN. Complete the connection in advance. The browser can set or operate : • LAN setting Configure Wired/Wireless LAN environment. • E-mail Setting Configure E-mail function to manage the projector remotely.
6. Configurations with Browser Introduction To operate by the browser, you need to prepare and configure the environment. Check the environment of the browser and configure to operate the projector. Browser Environment Browser is required to support the following version. Microsoft : Internet Explorer Ver.4.0 or later Netscape Communications : Netscape Communicator Ver6.0 or later Browser Configuration Configure the operating environment of the browser.
6. Configurations with Browser Starting up the Browser 1. Turn on the projector. 2. Activate NetworkModule Client (or NetworkModule Moderator). 3. Select the projector to set from the Network Projector List. (Selected projector will be blue.) 4. Click the Advanced settings button to display the Advanced settings. Click the Configure NetworkModule button to display the NetworkModule Configuration screen.
6. Configurations with Browser Information Display the current setting environment. The contents differ depending on Wired or Wireless LAN environment.
6. Configurations with Browser Parameters and descriptions of Information Parameter Description Firmware Version ............................Show the firmware version of the projector. Boot ROM Version ..........................Show the boot ROM version of the projector. Hardware Address ..........................Show the MAC address. IP Address ......................................Show the IP address currently set on the projector.
6. Configurations with Browser Quick Setup Set up minimum required items for operating the projector. These settings can also be done in "Advanced Setup". (p46-52) If you have set the items from the advanced setup, Quick Setup is not necessary. Setting items differ depending on the Wireless LAN and Wired LAN. To reflect the settings on the projector, click "APPLY". For details about each item/button, see next page.
6. Configurations with Browser Parameter Description English Projector..........................................Name each projector to distinguish it from other projectors. (up to 32 one-byte characters). The name set here will be displayed on the Network Projector List in the application operation screen. IP Configured Method ....................A desired IP address setup method is selected from "Manual", "DHCP", and "BOOTP".
6. Configurations with Browser Advanced Settings (Click "+" mark to display the subitems.) TCP / IP TCI/IP related items can be configured on this screen. Parameter Description IP Configuration Method ..........A desired IP address setup method is selected from "Manual", "DHCP", and "BOOTP". If "DHCP" or "BOOTP" is selected, the IP address is obtained automatically as "DHCP client" or "BOOTP client".
6. Configurations with Browser Wireless Setting Wireless related items can be configured on this screen. This screen will not be displayed at Wired LAN setting. Parameter Description Wireless Mode ................................Select the Communication standard 802.11b or 802.11b.g English Network Type ....................................Select either “Infrastructure” or “AdHoc”. SSID* ..............................................Set the SSID/ESSID.
6. Configurations with Browser E-mail The projector has a function to send e-mails to inform its operating condition to the administrators or users. This function can not be used for Wireless AdHoc mode. This function is available only for Wired or Wireless LAN infrastructure mode. Parameter Description SMTP Server ..................................Enter the address of SMTP server. (up to ASCII254 characters) Administrator Address ....................Enter the E-mail address of administrator.
6. Configurations with Browser Admin Password Set the Admin Password to prevent unauthorized person from changing the settings of the projector. At the factory settings, the Admin Password is not set. Parameter Description Enter Current Admin Password......Enter the currently set admin password. The password you have entered is displayed as “●●●●●●●”. (up to ASCII32 characters) Enter New Admin Password ..........Enter a new admin password you wish to set.
6. Configurations with Browser User PIN code With this screen, you can set the User PIN code to transfer the image to the projector and to activate PJ Controller. You can set different PIN code as you set for Admin Password. (p49) When you reset the User PIN code, you do not need to enter the current PIN code. At the factory setting, the User PIN code is not set. If you do not need to set a PIN code, enter "0000". Parameter Description Enter New User PIN code ............
6. Configurations with Browser Moderator Login Password To use the Moderator function, you need to set the Moderator Login password here. For operating the Moderator function, a Moderator Login password is required on this screen. When resetting the Moderator Login password, you do not need to enter the current Moderator Login password. Default setting is blank. If you do not want to set a password, leave here blank.
6. Configurations with Browser Miscellaneous You can set the name to the projector. The set name will be displayed on the Network Projector List of the application operating screen. Parameter Description Projector......................................Name a projector to distinguish it from other projectors. (up to 32 characters). The name set here will be displayed on the Network Projector List. Status Bar ......................................
6. Configurations with Browser Change Configuration Set Select a LAN settings from LAN1-LAN3, Off, LAN4, LAN5, and SIMPLE. With this screen, you can also confirm some settings ( Projector name, IP Configuration Method, IP Address, Wireless Mode, Network Type, Channel, SSID, WEP Security). Depending on Wireless or Wired input, setting items will be varied. Wireless LAN set menu English Wired LAN set menu Parameter Description LAN1-5,.SIMPLE* ..........................
6. Configurations with Browser Restart You can restart the projector on this screen. To enable the new settings, the projector has to be restarted. Click "RESTART". Parameter Description RESTART button ............................Click this button when you restart the projector after completing the settings. CANCEL button ..............................Cancel to restart the projector.
Chapter 7 7. Project the Image via the Networks English Project the image on the computer screen by operating the projector which is connected to the networks.
7. Project the Image via the Networks Real time Capture button (While capturing the image, the button will become Stop Capture button.) Network Projector List One-shot Capture button PJ Controller button 56 1. Activate NetworkModule Client (Participants) or NetworkModule Moderator (Moderator). 2. Adjust the projector input to the selected network (Wired or Wireless) with the PJ Controller. When operating multiple projectors, adjust each projector independently. Refer to "10.
Chapter 8 8. Use the Moderator Function English With Moderator function, the moderator can project the participants' computer screen through the projector in meetings or in classes.
8. Use the Moderator Function Moderator Function This function is useful for a moderator or a teacher to conduct a meeting or a class, where all the participants including the moderator (teacher) are assigned a computer, to project images from each participant's computer. A moderator (teacher) has the right to decide which computer image to project. One moderator (teacher) can conduct up to 50 computers.
8. Use the Moderator Function Preparation for Using the Moderator Function First, follow the procedure in "2. Setup Procedure" ➔ "Step 1-3" (p16) and confirm that the setting status is set as written below. •Client application (NetworkModule Client) is installed on each client's (except for the moderator) computer and each client's computer image can be projected. • Moderator application (NetworkModule Moderator) is installed on the moderator's computer and moderator's computer image can be projected.
8. Use the Moderator Function Setting the Moderator Function ✳ See p62 for Easy Settings. 1. Turn on the Moderator's computer and activate the moderator's application. Turn on the each client's computer and activate each of the applications. Registration of the Moderator 2. The moderator sets the Moderator Login password to the projector. When operating multiple projectors, set passwords to all the projectors. It is preferable to set the same password to all the projectors.
8. Use the Moderator Function Registration of the Clients (Participants) 6. Select the projector (Selected projector will be blue.) in the group from the client screen. (Moderator's projector will be pink.) Click the Join the moderated session button. Join the moderator session button English 7. Set session password screen will appear. Enter the password registered by a moderator (Being registered at step 4) 8. Click "OK".
8. Use the Moderator Function Unregister from Moderator Status 1. Select a projector which is registered as a moderator from the moderator screen. 2. Click the Exit moderator status button. Selected projector will be unregistered as a moderator. When there are multiple projectors to unregister, repeat the procedure for each projector. The moderator cannot unregister while an image is transferring to the projector. First, stop transferring the image and then unregister.
Chapter 9 9. How to Use Network Viewer English Project images on a FTP server, which is on the same LAN with the projector, through the projector by operating a projector or a computer. First, check if the projector and the computer are connected to the networks correctly with Wired or Wireless, to project the image properly.
9. How to Use Network Viewer The Mechanism of Network Viewer and the Flow of the Signal Network Viewer is to project an image stored on a FTP server which is on the same LAN as a computer, through the projector by operating a computer or a projector. The flow of the signal for each communication mode is shown below.
9. How to Use Network Viewer ■ Wired LAN Communication Mode Network Projector Wired LAN Connection Server Instruction Image Data FTP Server Computer Computer Operation Procedures for projecting the images on the FTP server are as follows. English 1. Information about the FTP server, which provides images, is sent from the computer to the projector and the information will be held. 2.
9. How to Use Network Viewer Projecting the Image Operation can be made with any of 1) PJ Controller, 2) Browser, or 3) Projector. When operating with the projector, first, set the FTP server which provides images with 1) PJ Controller or 2) Browser. Operate as follows. 1) Operating with the PJ Controller 1. Select the projector input (Wired /Wireless). Select "Wireless" for Wireless LAN and "Wired" for Wired LAN for the input source of the projector.
9. How to Use Network Viewer 5. Specify the FTP server to provide image data Host Name.... Enter IP address of the server. Folder Path.... Specify the directory where image data are stored. When the image data is in the root directory, just "/" will be displayed. When the image data is in a specified directory, put slashes"/" between directories such as /test/data etc. User ID ..........Enter login ID access to the server.* Password ......Enter login password access to the server.
9. How to Use Network Viewer 2) Operating with the Browser 1. Select "Wireless" for Wireless LAN and "Wired" for Wired LAN from the input menu of the projector. Activate " NetworkModule Client" or "NetworkModule Moderator". Operating directly from the browser is also possible. In this case, enter the projector IP address directly into browser's address bar. Configure NetworkModule button 2. Specify the projector to display the image Only one projector can be selected. 3.
9. How to Use Network Viewer 4. Specify the FTP server to provide image data Host Name.... ..........Enter the IP address of the server. Folder Path.... ..........Specify the directory where image data are stored. When the image data is in the root directory, just "/" is displayed. When the image data is in a specified directory, put slashes"/" between directories such as /test/data etc. User ID ....................Enter the login ID access to the server.* Password ................
9. How to Use Network Viewer 3) Operating with the projector Before operating the Network Viewer from the projector, the FTP server needs to be configured by PJ Controller or browser in advance. Regarding the configuration of the FTP server, refer to "1) Operating with PJ Controller" (p66, 67) or "2) Operating with browser". (p68, 69) 1. Configure the FTP server which provides image data, referring to "Operating with PJ Controller" or "Operating with browser". 2.
9. How to Use Network Viewer 4. Select, execute, and stop the mode of image replay. Move the red arrow pointer to the item you wish to choose. Using Point buttons and SELECT button of the projector, configure or execute each item. Auto ........................Play images and stop playing according to following configurations. Second ....................Set timing to switch images in Auto play mode. (3-240 sec.) ∞ ........................Set "On" to make the projector keep playing images repeatedly. Times .
Chapter 10 10. How to Use the PJ Controller English Control the projector operation on the network. PJ Controller works for; • Operating the projector • Operating the Network viewer • Controlling the projector Monitor the operation status of the projector in real time. Send an e-mail to the administrator about operation status of the projector. • Operating multiple projectors simultaneously.
10. How to Use the PJ Controller How to Operate This operation requires that the projector is set correctly on the network and the image in the computer is properly displayed from the projector with "NetworkModule Client" or "NetworkModule Moderator" applications on the computer. Activate the PJ Controller. 1. Activate the "NetworkModule Client" or " NetworkModule Moderator". 2. Select the Advanced settings screen. 3. Select a projector from the Network Projector List. (Selected Projector name will be blue.
10. How to Use the PJ Controller Initial Settings Before using the PJ Controller function, initial setting is required. Parameter English 1. Select Initial Setting from the main menu and configure each item. Description Language ........................................Select a desired language from the pull-down menu, and click "Set". Temperature ................................Set the unit of temperature displayed on the control screen of the projector.
10. How to Use the PJ Controller E-mail Setting The projector has a function to send an e-mail to inform its operating condition to the administrator or users. Select E-mail Setting from the main menu and configure each item as follows: 1. Registering E-mail Address Parameter Description SMTP Server ..................................Enter the address of SMTP server and click "Set". Administrator Address ....................Enter the E-mail address of administrator and click "Set". Mail Address .........
10. How to Use the PJ Controller 2. Check Option items Check the conditions where you would choose the projector to send an alert message. Regarding the alert message, see samples below. 3. Enter the message to attach the E-mail. The message typed here will be attached to the alert message. Samples of Alert Message * When the internal temperature is too high TITLE: Message from projector Projector Model Name: XX100 TCP/IP: 192.168.0.111 Projector Name: It sends you following message.
10. How to Use the PJ Controller Power & Status Click "Power & Status" on the main menu and configure each item. 1. Turning on/off the projector Click Standby / ON buttons. When clicking the Standby button, the confirmation message will appear. Click OK to turn off the projector. CAUTION: Projector cannot be turned on for approximately 90 seconds after it being turned off. When the display of "Power Status" changes from " On cooling down" to " On", click ON to turn on the projector.
10. How to Use the PJ Controller 2. Check the status of the projector The following items can be checked on the Power & Status screen. Parameter Description Accumulated lamp-use time............Display the accumulated time of lamp use in hour increment. Accumulated projector-use time ....Display the accumulated time of projector use in hour increment. Power Status ..................................
10. How to Use the PJ Controller Control When you select Control from the main menu, Control Menu will appear at the bottom of the screen. Using this menu, you can adjust or configure the projector. Note:Control items displayed on this screen are varied depending on the input source or product model of the projector. So the figures shown in this section may be different from the actual screen displayed on your computer. For further details, refer to the owner's manual of your projector.
10. How to Use the PJ Controller PC adjustment This feature optimizes the signal from the connected computer to display the screen. ✳ PC adjustment screen is displayed only when Computer1 (Analog) or Computer 2 (RGB) is Parameter English selected for the input source. Description Current Mode ..................Display computer mode Auto PC adjustment..........Executed by clicking Start button. Fine sync ..........................Click 7 8 to adjust the value Total dots ..........................
10. How to Use the PJ Controller SYSTEM Adjustment On this screen, you can select the color system and scan mode for the video signal. This screen is displayed only when Video (Video/Component) is selected for the input source of the projector. Depending on the signal, the screen is varied as follows. Component Input Parameter Description System Adjustment ..........Select a scan mode of component signal. AUTO ................................Automatically adjust to the scan mode of the input signal.
10. How to Use the PJ Controller Image Adjustment On this screen, you can adjust the image projected from the projector. Select an Image Adjustment Mode from the pulldown menu and click Set button. The items displayed on this screen is automatically changed according to the input signal. Click 7 8 buttons to adjust the value. Every time you change the value, click Set button. if you click Reset button, all the adjusted values will be reset.
10. How to Use the PJ Controller Screen You can select a screen mode on this screen. The items displayed on this screen is automatically changed according to the input signal. Parameter Description Aspect ................Select "Norma"l, "Real*", "Wide", or "Full screen*". Digital Zoom* ....Click "+", or " _" button to enlarge or minimize the screen size. Click "OFF" to cancel this function. * Items only for Wireless, Wired Computer1 (Analog) or Computer2 (RGB) input mode.
10. How to Use the PJ Controller Setting English On this screen, you can configure the projector. Refer to the next page for each item and description. The items displayed on this screen are varied according to the functions provided to the projector.
10. How to Use the PJ Controller Parameter Description Language ..........................Select the desired language from the pull-down menu. Auto Setup........................Automatically set PC adjustment and correct keystone distortion. Auto PC Adjust. ...Select "On" to automatically set the PC adjustment. Auto Keystone ............Select Auto to automatically correct keystone distortion, and select "Manual" to set keystone distortion when the Auto set button is clicked. Keystone ...................
10. How to Use the PJ Controller Service Items on this screen are used for maintenance of the projector. Parameter Description Fan Control Speed ........................Select "Max" or "Normal". Video System* ....Display the current video system. Horizontal* ........Click 7 8 buttons to adjust horizontal screen size. Vertical* ..........Click 7 8 buttons to adjust vertical screen size. Position* ..........Click 7 8ed buttons to adjust the screen position. Initialize* ............
10. How to Use the PJ Controller 2. Select Set Number and name the setting Select the Set Number you wish to store the adjustment from the pull-down menu. Enter the name of the setting in the Memo field. Enter the name of the setting 3. Save the setting (Set) Click Save button to save the adjustment. Loading the Set Click the pull-down menu of Load Setting No. and select the set number you wish to load. Click Set button to display the value of the set. Select the set number from the pull-down menu.
10. How to Use the PJ Controller Multi Control With this function, multiple projectors can be operated simultaneously. You can operate up to 64 projectors at the same time. With this function, you can also operate the projector which is attached a MultiCard Imager and on the same network. Operation 1. Activate NetworkModule Client (or NetworkModule Moderator), and call up the Advanced Settings screen. 2.
10. How to Use the PJ Controller Parameter Description Power................................Turn on or off the projector. ✳ When using the Multi Control function, set "Normal" from "Setting menu" ➔ "Standby mode". If selecting "Eco", you cannot turn on the projector again after turning off. Input..................................Select projector input. Image................................Select Image mode. Aspect ..............................Select aspect of the screen. Digital Zoom....................
Chapter 11 11.
11. Appendix Troubleshooting If you have any trouble in setup or operation of the projector, refer to the troubleshooting items and check the relevant matters described. ■ The computer cannot connect projectors. Wired LAN Is the LAN cable connected to the projector properly? Are the Link lamp and Access lamp of the LAN terminal lighting properly? Not lighting : The LAN setting of the projector is set "On"? See "Wired LAN setting" in the projector menu.
11. Appendix Infrastructure Mode: When selecting LAN5 (factory default setting) Check each item below in the Wireless Setting menu of the projector as follows: *IP Address ..................No setting is required. *Sub net ......................Should be same as the setting of the access point *Gateway......................Should be same as the setting of the access point *Network Type ............Should be the Infrastructure mode *ESSID/SSID/IBSSID....
11. Appendix ■ Cannot start up the browser Is connection between PC and the projector with NetworkModule Client (or NetworkModule Moderator) established? No........Check settings for Wireless/Wired LAN. Yes ....Check settings of the proxy setting at browser. Refer to "6. Browser Configurations" (P 40) ■ Although connection between PC and the projector is established, images are not projected on the screen. Make sure Wireless/ Wired is selected from the Input source menu of the projector.
11. Appendix Terminology DHCP server (Dynamic Host Configuration Protocol) It is necessary to set an IP address for each computer or equivalent equipment when establishing a network by TCP/IP. If there exists DHCP server on the network, it will assign IP addresses to client computers every time they request it. If there exists equipment with DHCP server functions (such as a Windows 2000 server and a dial-up router)on the network, the DHCP server function may be automatically operating.
11. Appendix Setting up the IP address with “arp” + “ping”command You can use “arp” and “ping” command from Command Prompt to assign an IP address to your projector. 1. Start up projector and configure the Wired or Wireless LAN to communicate with the computer. 2. From Windows "Start" menu, click "Run". In the field next to "Open:", enter “command” and click OK. When “MS-DOS prompt” (or command prompt) appears, type in “arp” command as follows: (Example) C:\ > arp -s 169.254.1.
