PjNET-30 OWNER'S MANUAL K LIN ACT Pj-to NetDirector Quick Setup Guide ENGLISH The owner's manuals of Pj-to NetDirector are included on the supplied document CD-ROM as the PDF file format. To read the owner's manual, set the document CD-ROM onto your computer and follow the guide on the screen. To read the owner's manual, you need the Adobe Reader (Adobe Acrobat Reader) version 6.0 or later software in your computer. The Adobe Reader can be obtained from the Adobe website (http://www.adobe.com).
Read this First Compliance Federal Communication Commission Notice This equipment has been tested and found to comply EIKI PjNET-30 with the limits for a Class B digital device, pursuant to Tested To Comply part 15 of the FCC Rules. These limits are designed to With FCC Standards provide reasonable protection against harmful interference in a residential installation.
Read this First caution ON Use in network - When you receive an alert e-mail from the projector, you must check the projector immediately. Fire or accident may result if the projector is used in an abnormal condition. - When you install the projector at remote location and use it through the network, you must perform the safety inspections periodically. In this case you must pay attention to the change of environment in which you installed the projector.
Read this First Package contains The package contains following items. Check each item as you unpack the package. If you have any of the following items missing, contact the sales dealer.
Read this First Operating environment To perform the managing and setting of the projector by using this product, the environment described below is required. Standard mode Operating System Windows 98, Windows Me, Windows NT4.
Setting up Name and function of each part (Top View) POWER indicator This lights up red when the network function is set ON in the projector menu. Mounting screws Mount by using a coin etc. K LIN ACT ACT indicator This turns on and off with green when sending or receiving of data LINK indicator This lights up red when the network unit is connected to the network correctly. (Bottom View) Connector plug Connecting to the terminal on the projector.
Setting up Installation and network configuration Connector Cover Mounting 1 Disconnect the AC plug from the projector. Screw Cover 2 R emove the connector cover and screw covers (2 pieces) from the projector and insert plug on this product to the option connector. 3 T ighten two screws by using a coin etc. Screw Cover Connection of LAN cable To connect to the network, it is required to use the UTP (Unshielded Twisted Pair) straight cable with RJ-45 plug.
Setting up Network configuration Confirmation of the network menu When installing this product to the projector, the network on-screen menu items for this product are activated automatically. If not activated, the product may not have been installed correctly. Please check item "Mounting" (☞ p.7). Configure the network Before performing the network configuration, prepare network address numbers (IP Address, Subnet Mask, Default Gateway, DNS) assigned to the projector.
Setting up 2 Configuration for IP Address/ Sub net/ Gateway*1/DNS*2 Press SELECT button again. The following network setting pallet appears on the screen. Enter the specified network addresses. The red frame moves sequentially left or right with 7 8 button. The number up or down with d e button.
Setting up Login the setting page of the projector 1 Enter the IP address Launch the web browser installed in your computer, enter the IP address into the "Address" on the browser and then press "Enter" key. Enter the address (192.168.1.201) that you configured in item "Network configuration" (☞ p.9). The default IP address is [192.168.0.2]. 2 Select a display mode and login This product provides 2 types of control mode, Standard Mode and Light Mode as the below.
Setting up 3 Display of main setting page The following main setting page will be displayed according to your display mode selection. Perform various kinds of settings through this page. Click on the menus to display the control and setting pages.
Software Installation Guide Installing the software To install the software into the computer with Windows 2000, Windows XP or Windows NT, you should logon as administrator. Before installation, make sure that the other applications are closed, otherwise installation cannot be made properly. Network Viewer & Capture 3 installation 1 Set the supplied Network Viewer & Capture 3 CD-ROM into the CD-ROM drive of your computer. Double click SetupTool.exe icon in the "Tool" folder in the CD-ROM.
Software Installation Guide Installed software and places Network Viewer 3 (File Converter 2) is installed in the "Printers and Faxes" folder in the "Control Panel". ● Network Viewer 3 (File Converter 2): This is a kind of the printer driver to convert to the JPEG data optimized to project by the projector from any of the documents created by the application software. PJ Network Manager installation 1 S et the supplied CD-ROM into the CD-ROM d r i v e o f y o u r co m p u te r.
U.S.A. Canada EIKI International, Inc. 30251 Esperanza Rancho Santa Margarita CA 92688-2132 U.S.A. Tel : 800-242-3454 (949)-457-0200 Fax : 800-457-3454 (949)-457-7878 E-Mail : usa@eiki.com EIKI CANADA - Eiki International, Inc. P.O. Box 156, 310 First St. - Unit 2, Midland, ON, L4R 4K8, Canada Tel : 800-563-3454 (705)-527-4084 Fax : 800-567-4069 (705)-527-4087 E-Mail : canada@eiki.
