International Multimedia Projector Quick Reference Guide
]
TURNING ON / OFF PROJECTOR
TURNING ONTHE PROJECTOR
1 Complete peripheral connections.(with a computer,
VCR, etc.) before turning on the proJector.
2 Connect the projector's AC power cord into an AC
outlet. The LAMP indicator lights RED,and the READY
indicator lights GREEN.
3 Press the POWER ON-OFF bunoo o.n the top ~ontrol or
on the remote control. The LAMP mdicator dims. and
the cooling fans start to operate. The preparation
display appears on the screen and the countdown
starts.
4 After the countdown. the input source that was
selected the last time and the Lamp control status icon
appear on the screen.
If the prOjector is locked with a PINcode, a PINcode Input
DialogBox appears. Enter a PINcode as instructed below
00
To Enter a PIN code
Select a number by pressing the POINT LEFTIRIGHT button and fix
the number with the SELECT button. The number changes to "*. ~
If you fixed a wrong number, move the pointer to "Set~ or ~Clear~
once by pressing the POINT DOWN button, then return to ~PIN
code. ~ Enter the correct number.
Repeat this step to complete entering a four.(jigit number.
When the four-digit number is fixed, the pointer automatically
moves to "Set. ~ Press the SElECTbutton so that you can start to
operate the prOJector.
If you entered a wrong PIN code. UPIN code" and the number
(***.) turn red and disappear. Enter a PIN code all over again.
What is PIN code?
PIN (Personal Identification Number) code is a security code that
allows the person who knows it to operate the projector. Setting a
PIN code prevents unauthorized use of the projector.
A PIN code consists of a four digit number. Refer to PIN code lock
function in SETTING Menu in the owner's manual for locking the
operation of the projector with your PIN code.
CAUTION ON HANDLING PIN CODe
If you forget your PIN code. the projector can no
longer be started. Take special care in setting a new
PIN code; write down the number in a column on
page 60 of the owner's manual and keep it at hand
Should the PIN code be missing or forgotten, consult
your dealer or service center
The preparation display disappears after 30 seconds
Selected Input Source and Lamp control
F=
"" I
I tGI(/<C I
Q « Lampcontrotstatus
PIN code Input Di.log Box
~'" ...,. c:::=::::J$ ...L.Pointer
I
.
.. m. 0!CJ'" '"I
..
co...
.
~ After the OK icon
disappears, youcan
operate the projector
1
Press the POWER ON-OFF button on the top control or
on the remote control, and "Power off?" appears on
the screen.
TURNING OFFTHE PROJECTOR
2 Press the POWER ON-OFF button again t? turn off the
projector. The lAMP Indicator lights brrght and the
READY Indicator turns off. After the projector is turned
off, the cooling tans operate (for 90 seconds). During
this "cooling down" period, the projector cannot be
turned on
3 When the projector has .cooled down, the READY
Indicator lights GREEN agaIn and you can turn projector
on. After cooling down completely, unplug the AC
power cord.
TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN
THE PROJECTOR ON, WAIT AT LEAST FIVE
MINUTES BEFORE TURNING IT OFF
DO NOT UNPLUG THE AC POWER CORD WHILE
COOLING FANS ARE RUNNING OR BEFORE THE
READY INDICATOR LIGHTS GREEN AGAIN.
OTHERWISE IT WILL RESULT IN SHORTENING THE
LAMP LIFE.
"'Note:
.The projector connor be rumed on during the cooling period with the
READYindi<awwmed off. Youcan wrn it on agarn after the READY
indicator becomesGREENagain.
.When the On srort funcrion is "On." rhis prOjector is turned on
O!Jromofically by connecting the AC power con:J to an AC O<Jr1et
.Continuous use may resulr in shortening the lamp life. Turn off the projectof-
and resr ir for abour an hour.n every 24 hours.
.The running speed of cooling fans is chonged according 0 the remperarure
insidethePR1j«ror.
.If rhe WARNING TEMP indicator blinks RED. see 'WARNING TEMP
INDICATORHin the ownersmonoaf.