MULTIMEDIA PROJECTOR MODEL LC-X2U LC-X2UL (Without Lens) OWNER’S INSTRUCTION MANUAL
INFORMATION TO THE USER NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the owner’s manual, may cause harmful interference to radio communications.
IMPORTANT SAFETY INSTRUCTIONS All the safety and operating instructions should be read before the product is operated. Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. Do not use attachments not recommended manufacturer as they may cause hazards. by the Do not place this projector on an unstable cart, stand, or table.
TABLE OF CONTENTS PAGE FEATURES AND DESIGN 5 INTRODUCTION COMPATIBILITY IMAGE RESOLUTION AUTOMATIC MULTISCANNING SYSTEM SCREEN MODE MULTILANGUAGE UNPACKING THE PROJECTOR TRADEMARKS 5 5 5 5 5 5 5 5 INSTALLATION 6-9 NAME OF EACH PART OF THE PROJECTOR 6 SETTING-UP THE PROJECTOR 7 MOVING THE PROJECTOR POWER REQUIREMENTS 8 9 CONNECTING THE PROJECTOR 10-21 TERMINAL OF THE PROJECTOR CONNECTING THE COMPUTER CONNECTING THE VIDEO EQUIPMENT BEFORE OPERATION CONTROLS AND INDICATOR OPERATION OF THE REMOTE CON
FEATURES AND DESIGN INTRODUCTION The multimedia projector that combinesx powertul and sophisticated teatures with easy-to-use, intuitive controls. Built-in multimedia features include audio, a palette of 16.77 million colors and active matrix liquid crystal display (LCD) technology. The projector is ideal for high-performance business, training and imaging applications that demand exceptional color quality.
• This projector is basically designed to project on a flat projection surface. • This projector can be focused from 4.9’ (1.5 m) ~ 80.7’ (24.6 m). • Refer to the figure below as an example when positioning the projector to the screen. THIS PROJECTOR SHOULD BE SET IN THE WAY INDICATED. NEVER HANG THE PROJECTOR, OR FALL DOWN ON ITS SIDE. IT MAY RESULT IN FIRE HAZARD. Picture tilt and projection angle can be adjusted by twisting ADJUSTABLE FEET.
This projector is equipped with a cooling fan to protect it from overheating. Pay attention to the following to ensure the ventilation and avoid a possible risk of fire and malfunction. •Do not cover the vents with papers or other materials. •Keep the rear grill at least 3.3’ (1 m) away from any object. •Make sure that there are no objects under the projector. An object under the projector may prevent the projector from taking the cooling air through the bottom vent.
Your projector uses nominal input voltages of 100-120 VAC. The projector automatically selects the correct input voltage. The projector is designed to work with single-phase power systems having a grounded neutral conductor. To reduce the risk of electrical shock, do not plug into any other type of power system. Consult your authorized dealer or service station if you are not sure what type of power is supplied to your building.
1 COMPUTER INPUT-1 TERMINAL (ANALOG HDB 15-PIN) 8 CONTROL PORT-1 CONNECTOR COMPUTER INPUT-1 RMINAL (DIGITAL MDR 20PIN) 9 CONTROL PORT-2 CONNECTOR COMPUTER INPUT-2 JACKS (BNC TYPE x 5) 10 11 USB PORT-1 CONNECTOR 12 SERIAL PORT TERMINAL (DB9) 13 WIRED REMOTE JACK Used to connect a computer to the projector. 2 Used to connect a computer to the projector. 3 4 Used to connect a computer to the projector. MONITOR OUTPUT TERMINAL (ANALOG HDB 15-PIN) Used to connect a monitor to the projector.
14 VIDEO INPUT JACKS-1 (BNC TYPE x 3) 19 AUDIO INPUT JACKS-2 (R and L) 15 S-VIDEO INPUT JACK-1 20 VIDEO MONITOR OUTPUT JACKS (BNC TYPE x 3) 16 AUDIO INPUT JACKS-1 (R and L) 21 VIDEO MONITOR (S-VIDEO) OUTPUT JACK 17 VIDEO INPUT JACKS-2 (BNC TYPE x 3) 22 AUDIO MONITOR OUTPUT JACKS (R and L) 18 S-VIDEO INPUT JACK-2 Used to connect a video source to the projector. Used to connect a S-VHS video source to the projector. Used to connect an audio source to the projector.
Personal computers can be connected to the HDB1 5-pin (VGA) terminal on the projector. • Connect the computer to these terminals using the VGA cable and VGA/MAC adapter (provided). CAUTION: For projectors, the VGA cable provided is designed to reduce RFI (Radio Frequency Interference) emissions. For regulatory compliance reasons, this cable must be used and must not be replaced by any other cable. Digital output signal from the computer can be connected to the DIGITAL terminal (MDR 20-pin).
This terminal output the information of the selected computer source being viewed on the screen (Computer 1 or Computer 2). When video source (“Video 1” or “Video 2”) is selected, this terminal outputs Computer 1 input information. An external monitor can be connected to the HDB15-pin (VGA) terminal on the projector. • Connect the monitor to this terminal usinq the VGA cable (not provided). Pin No./Signal 1 Red input 2 Green input 3 Blue input 4 Sense 2 5 Ground (Horiz.sync.
CONNECTING AN IBM-COMPATIBLE DESKTOP NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.
‘NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.
NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.
NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.
NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.
NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.
CONNECTING TO THE VIDEO INPUT JACKS (1 and 2) BNC TYPE x 3 Connect to the video outputs of a VCR, video disc player, DVD player, video camera, satellite TV tuner or other AV equipment. Connect video output from AV equipment to these jacks using the BNC cables. The video input can be connected 3 types of signals; “COMPOSITE VIDEO”, “Y/C SEPARATE VIDEO” and COMPONENT VIDEO {Y, Cb (B-Y), Cr (R-Y)}. Set VIDEO SOURCE of each video input (VIDEO IN-1 or VIDEO IN-2) to input video matter.
NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be disconnected from AC outlet. Turn the projector on before the peripheral equipment is switched on.
1. LAMP REPLACEMENT INDICATOR 2. TEMPERATURE WARNING INDICATOR 3. READY INDICATOR 4. LAMP POWER INDICATOR Light is orange when the Lamp life draws to an end. Flashes red when internal projector temperature is too high. Light is green when projector lamp is ready to be turned on. Light is dim when the projector is on. Light is brightened when the projector is in stand-by mode. 5. VOLUME BUTTONS 6. ZOOM 7. FOCUS BUTTONS 8. LENS SHIFT BUTTONS 9. POWER ON/OFF BUTTON 10. MODE BUTTON Used to adjust volume.
This remote control unit is not only able to operate the projector but also usable as a wireless mouse for a PC. One pointing pad and two click buttons are used for wireless mouse operation. Wireless mouse is usable when PC mouse pointer is displayed on the screen. When the menu or indicator of the projector is displayed on the screen instead of the PC mouse pointer, the wireless mouse cannot be used. NOTE: To use the unit as a PC wireless mouse, connect the projector to the PC with the attached cable.
SELECT BUTTON 1. COMPUTER SELECT BUTTON 2. VIDEO ON/OFF BUTTON 3. POWER VOLUME BUTTONS 4..ZOOM BUTTON 5 P-TIMER BUTTON 6. FOCUS BUTTON 7. FREEZE/NO SHOW BUTTON 8. SOUND MUTE BUTTON 9. LENS SHIFT BUTTON 10.CURSOR BUTTON 11. AUTO IMAGE BUTTON Used to select computer mode. (Computer 1 or Computer 2 Input) Used to select video mode. (Video 1 or Video 2 Input) Used to turn the projector on or oft. Used to adjust volume. Used to select power zoom lens adjust. Used to operate the P-TIMER function.
Point the remote control toward the projector (Receiver window) whenever pressing the buttons. Maximum operating range for the remote control is about 16.4’ (5m) and 60o front and rear of the projector. To insure safe operation, please observe the following precautions: • Use (2) AA type alkaline batteries. • Change two batteries at the same time. • Do not use a new battery with a used battery. • Avoid contact with water. • Do not drop the remote control unit.
1. 2. WIRED REMOTE JACK When using the wired remote control, connect the remote cable to this jack. COMPUTER SELECT BUTTON Used to select computer mode. (Computer 1 or Computer 2 Input) 3. VIDEO SELECT BUTTON 4. POWER ON/OFF BUTTON 5. VOLUME BUTTONS 6. ZOOM BUTTONS 7. FOCUS BUTTONS 8. SOUND MUTE BUTTON 9. LENS SHIFT BUTTONS 10.P-TIMER BUTTON 11.AUTO IMAGE BUTTON 12.MENU BUTTON Used to select video mode. (Video 1 or Video 2 Input) Used to turn projector on or off. Used to adjust volume.
The remote control unit can be used as wireless or wired remote control. Point the remote control toward the projector (Receiver window) whenever pressing the buttons. Maximum operating range for the remote control is about 16.4’ (5m) and 60° front and rear of the projector Connect a remote control cable to R/C jacks located on the wireless/wired remote control unit and the side of the projector. To insure safe operation, please observe the following precautions: • Use (2) AA type alkaline batteries.
The projector has two types of operation: DIRECT OPERATION and MENU OPERATION. DIRECT OPERATION allows you to operate the projector by using one button without showing the MENU. In MENU OPERATION mode, you display menus where you can adjust the projector’s settings. Follow the instruction for each control.
MENU OPERATION ADJUST ITEM TOP CONTROL OF THE PROJECTOR WIRELESS/WIRED REMOTE CONTROL WIRELESS REMOTE CONTROL MODE SELECT MENU POINT LEFT/RIGHT SELECT POINT UP/DOWN SELECT MENU POINT LEFT/RIGHT SELECT POINT UP/DOWN SELECT MENU POINT (LEFT/RIGHT) SELECT (REAR CLICK) POINT (UP/DOWN) SELECT (REAR CLICK) 1. COMPUTER/VIDEO MODE ADJUST ITEM TOP CONTROL OF THE PROJECTOR WIRELESS/WIRED REMOTE CONTROL WIRELESS REMOTE CONTROL SOUND SOUND VOLUME TREBLE BASS BUIT-IN SP.
3.
Connect the projector to a source (Computer, VCR, Video Camera, Video Disc Player, etc.) using the appropriate terminals on the side of the projector (See “CONNECTING THE PROJECTOR” section on pages 10- 21). Connect the projector’s AC power cord into a wall outlet and turn the MAIN ON/OFF switch (located on the side of the projector) to the ON position. The LAMP POWER indicator will light RED, the READY indicator will light GREEN.
Press the MODE button on the projector or the COMPUTER and VIDEO button on the remote control unit to select Computer 1, Computer 2, Video 1 or Video 2 Input. The “Computer 1”, “Computer 2”, “Video 1” or “Video 2” display will appear on the screen for a few seconds. Press the VOLUME buttons on the projector or on the remote control unit to adjust the volume. The volume display will be displayed on the screen for a few seconds.
Press the D. ZOOM button on the wireless remote control unit. The “D.zoom” and the magnifying-glass icon is displayed to indicate Digital zoom mode. Digital zoom mode can be adjust the image size or pan the image. To expand the image size, press SELECT (REAR CLICK) button. The image is magnified by degrees (Expand function). To compress the image size, press FRONT CLICK button. The size of image is reduced by degrees (Compress function).
You can select a mode from MAIN MENU display among computer 1, computer 2, video 1, video 2. 1.Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear. 2.Press the POINT LEFT/RIGHT BUTTON(s) to select Computer or Video and press the SELECT (REAR CLICK) BUTTON. Another dialog box MODE DISPLAY will appear. 3.Press the POINT DOWN BUTTON and a red arrow will appear. 4.
You can adjust the sound volume, treble, bass levels and Built-in SP., Sound Mute ON/OFF switch in the MENU display. 1.Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear. 2.Press the POINT LEFT/RIGHT BUTTON(s) to select SOUND and press the SELECT (REAR CLICK) BUTTON. Another dialog box SOUND ADJUST DISPLAY will appear. 3.Press the POINT DOWN BUTTON and a red arrow will appear. 4.Move the arrow to an item that you want to adjust by pressing the POINT UP/DOWN BUTTON(s). 5.
This projector is compatible with the six major broadcast video standards: PAL, SECAM, NTSC, NTSC 4.43, PALM and PAL-N (COLOR SYSTEMs). When the color system is set to “Auto position”, this projector can detect one of 4 systems (PAL, SECAM, NTSC or NTSC 4.43) automatically. However, if the video signal is not strong enough to detect the video format, the projector may not reproduce the proper video image. In case this happens, this projector allows you to choose a specific broadcast signal format. 1.
Picture adjustments have been preset at the factory. If you want to change the setting, operate the projector as follows. 1.Press MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear. 2.Press the POINT LEFT/RIGHT BUTTON(s) to select IMAGE and press the SELECT (REAR CLICK) BUTTON. Another dialog box IMAGE ADJUST DISPLAY will appear. This shows the current picture settings. 3.In this dialog box, you can adjust the settings by increasing or decreasing the levels shown as numbers.
This projector has the Wide function, which enables you to view a wider video image. WIDE function This projector is able to project not only a normal video image (with 4 x 3 aspect ratio), but also a wider video image by compressing 4 x 3 image. This feature enable you to enjoy watching pictures like cinema images. You can switch either to WIDE or to REGULAR screen mode. 1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear. 2.
This projector is adjustable to different types of computer display signals based on VGA, SVGA, XGA or SXGA (See “COMPATIBLE COMPUTER SPECIFICATIONS” on the next page). If you set MODE SELECT to “COMPUTER”, the projector will automatically process the incoming signal and project the proper image without any special setting. Although this will work in most cases, you may be required to manually set the projector for some computer signals.
Specifications are subject to change without notice. NOTE: Basically this projector can accept the signal from all computers with the above mentioned V, H-Frequency and less than 200 MHz of Dot Clock.
The Auto image function is provided to automatically adjust Fine sync., Total dots and Screen position for most computers. NOTE: This auto image function will be skipped when the incoming signal is digital. 1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear. 2. Press the POINT LEFT/RIGHT BUTTON(s) to select AUTO IMAGE and press the SELECT (REAR CLICK) BUTTON. Another dialog box AUTO IMAGE SETTING DISPLAY will appear. 3. Press the POINT DOWN BUTTON and a red arrow will appear. 4.
Picture adjustments have been preset at the factory. It you want to change the setting, operate th projector as follows 1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear. 2. Press the POINT LEFT/RIGHT BUTTON(s) to select IMAGE and press the SELECT (REAR CLICK) BUTTON. Another dialog box IMAGE ADJUST DISPLAY will appear. This shows the current picture settings. 3. In this dialog box, you can adjust the settings by increasing or decreasing the levels shown as numbers.
1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear. 2. Press the POINT LEFT/RIGHT BUTTON(S) to select POSITION and press the SELECT (REAR CLICK) BUTTON. Another dialog box POSITION SETTING DISPLAY will appear. 3. Press the POINT DOWN BUTTON and a red arrow will appear. 4. Move the arrow to a desirable direction (Ã,Ä,Å,Æ) by pressing the POINT LEFT/RIGHT/UP/DOWN BUTTON(s) and press the SELECT (REAR CLICK) BUTTON to a desirable picture position. 5.
This function will be skipped when the incoming signal is digital. S This projector can automatically detect most display signals from most personal computers currently distributed. However, some computers adopt a special signal format which is different from the standard one and the projector cannot detect it. If this happens, the projector cannot reproduce a proper image. And a flickering picture, a nonsynchronized picture, a non-centered picture or a skewed picture may be projected instead.
6. Another dialog box “PC ADJUSTMENT DISPLAY 1” will appear and the parameter data for the Mode you have selected is shown in this dialog box. 7. The parameters will be filled with the data determined by the projector according to the present signal input. 8. The function of the parameters and their values are summarized in the table as below. 9. Move the arrow to an item that you want to adjust by pressing the POINT UP/DOWN BUTTON(s). 10.
17. Another dialog box “PC ADJUSTMENT DISPLAY 2” will appear and the parameter data for the Mode you have selected is shown in this dialog box. p18. Move the arrow to an item that you want to adjust by pressing the POINT UP/DOWN BUTTON(s). 19. To increase the level, point the arrow to S and then press the SELECT (REAR CLICK) BUTTON. To decrease the level, point the arrow to T and then press the SELECT (REAR CLICK) BUTTON. 20.
MODE FREE The Mode free function is provided to confirm or clear the parameter data produced by PC ADJUST. 1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear. 2. Press the POINT LEFT/RIGHT BUTTON(s) to select PC ADJUST and press the SELECT (REAR CLICK) BUTTON. Another dialog box “Where to reserve” will appear. 3. Press the POINT DOWN BUTTON and a red arrow will appear. 4.
This projector can adjust the image size and pan the image with PICTURE SCREEN ADJUSTMENT. 1. Press MENU BUTTON and MAIN MENU DISPLAY dialog box will appear. 2. Press POINT LEFT/RIGHT BUTTON(s) to select SCREEN and press the SELECT (REAR CLICK) BUTTON. Another dialog box SCREEN ADJUST DISPLAY will appear. 3. Press POINT DOWN BUTTON and a red arrow will appear. 4.
Turn WhenSPLIT this function WIPE function is in theOn “On” in position, the SETTING the left/right menu. The picture picture reverse will change capability into next one by sliding black image side ways when the input source is changed. This projector has other functions setting: Blue back, Display, Reverse T/B, Reverse R/L, Split wipe, Power management, USB, Remote control and Lamp age. off.
This projector can be operated with two different code, one is factory-set normal code (MODE 1) and the other one is extended code (MODE 2). This is used to prevent the remote control operation mixture (jam) when two projector and several remote control video equipments are system-up and used together. When you change the code MODE 2, you must change both projector and Remote Control Unit. To change Projector code: Set REMOTE CONTROL in SETTING menu (below figure) to “MODE 2”.
The Lamp age function is designed to reset the lamp replacement monitor timer. When replacing the lamp, reset the lamp replacement monitor timer by using this function. NOTE: Do not reset the LAMP REPLACEMENT MONITOR TIMER, except after the lamp is replaced. 1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear. 2. Press the POINT LEFT/RIGHT BUTTON(s) to select SETTING and press the SELECT (REAR CLICK) BUTTON. Another dialog box SETTING DISPLAY will appear. 3.
The TEMPERATURE WARNING INDICATOR flashes red when the internal temperature of the projector exceeds the normal temperature. Possible causes for the temperature warning may be: 1. Ventilation slots of the projector are blocked. In such an event, reposition the projector so that ventilation slots are not obstructed. 2. Air filter is clogged with dust particles. Remove dust from the air filter by following instructions in the Air Filter Care and Cleaning section above.
WHEN THE PROJECTION LAMP OF THIS PROJECTOR DRAWS TO AN END, THE LAMP REPLACEMENT INDICATOR LIGHTS YELLOW AND THE WARNING MESSAGE “LAMP REPLACEMENT” APPEARS AS THE RIGHT FIGURE. WHEN THE WARNING MESSAGE IS DISPLAYED, THE PROJECTION LAMP SHOULD BE REPLACED. To terminate the warning message. Replace the Projection Lamp and reset the LAMP REPLACEMENT MONITOR TIMER (See “LAMP AGE” section on page 52.), and the warning message is terminated. To erase the warning message in a moment.
Follow these steps to clean the projection lens: 1. Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner. Abrasive cleaners, solvents or other harsh chemicals might scratch the lens. 2. Lightly wipe the cleaning cloth over the lens. 3. When you don’t use the projector, replace the lens cover. - Before calling your dealer or service station for assistance, check the matters below once again. 1.
Problem: Picture is T/B inverted, Picture is L/R Reversed. Some displays are not seen during the operations No sound. Remote control unit doesn’t work. Wireless mouse function does not work. Try these Solutions: Check Reverse T/B feature. (See “OTHER FUNCTION SETTING” section on pages 50 Check Reverse L/R feature. (See “OTHER FUNCTION SETTING” section on pages 50 51). Check Display feature. (See “OTHER FUNCTION SETTING” section on pages 50 51).
Projector Type Dimensions (W x H x D) Net Weight LCD Panel System Number of Pixels Color System Scanning Frequency Projection Image Size (Diagonal) Horizontal Resolution Projection Lens Motorized Lens Shift Throw Distance Projection Lamp AV Input Jacks Video Monitor Output Jack Audio Monitor 0utput Jacks Computer Input 1 Jack Computer Input 2 Jack Computer Audio Input Jack Computer Output Jack Computer Audio Output Jack Other Jack Built-in Speaker Image Elevation Adjustment Wattage Power Consumption Operati
Audio Visual/Video Products EIKI INTERNATIONAL, INC. 26794 Vista Terrace Drive, Lake Forest, CA. 92630-8113, U.S.A. TEL (949) 457-0200 FAX (949) 457-7878 IN CANADA, EIKI CANADA 865 Heritage Drive P.O. Box 156 Midland Ontario L4R 4K8 Canada TEL (705) 527-4084 FAX (705) 527-4087 Printed in Japan Part No. 610 280 7554 (1AA6P1 P1 950-- ME6B) © 1999 Eiki International Inc.
