EIP-3500 SERVICE MANUAL S04A7XG-MB70X TM DLP PROJECTOR MODEL EIP-3500 In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used. This document has been published to be used for after sales service only. The contents are subject to change without notice.
EIP-3500 CONTENTS Page Page • SPECIFICATIONS ............................................ 3 • IMPORTANT SERVICE SAFETY NOTES .............................................................. 4 • NOTE TO SERVICE PERSONNEL .................. 6 • OPERATION MANUAL ................................... 10 • DIMENSIONS ................................................. 16 • REMOVING OF MAJOR PARTS .................... 17 • RESETTING THE TOTAL LAMP TIMER ......... 22 • THE OPTICAL UNIT OUTLINE ......................
EIP-3500 SPECIFICATIONS Product type DLPTM Projector Model EIP-3500 Video system NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL-60/SECAM/ DTV480I/DTV480P/DTV540P/DTV576I/DTV576P/DTV720P/DTV1035I/DTV1080I Display method Single Chip Digital Micromirror DeviceTM (DMDTM) by Texas Instruments DMD panel Panel size: 0.7" No. of dots: 786,432 dots (1,024 [H] × 768 [V]) Lens 1.5 × electric zoom/focus lens, F2.0 – 2.5, f = 21.3 – 31.
EIP-3500 IMPORTANT SERVICE SAFETY NOTES (for USA) Ë Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and servicing guidelines as follows: » Use an AC voltmeter with sensitivity of 5000 ohm per volt., or higher, sensitivity to measure the AC voltage drop across the resistor (See Diagram). » All checks must be repeated with the AC plug connection reversed.
EIP-3500 PRECAUTIONS A PRENDRE LORS DE LA REPARATION Ë Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux conseils suivants. AVERTISSEMENT conduite électrique ou une prise de terre branchée à la terre. • Utiliser un voltmètre CA d'une sensibilité d'au moins 5000Ω/V pour mesurer la chute de tension en travers de la résistance.
EIP-3500 NOTE TO SERVICE NOTE POUR LE PERSONNEL PERSONNEL D’ENTRETIEN 123456789012345678901234567890121234567890123456 123456789012345678901234567890121234567890123456 123456789012345678901234567890121234567890123456 123456789012345678901234567890121234567890123456 UV-RADIATION PRECAUTION 123456789012345678901234567890121234567890123456 123456789012345678901234567890121234567890123456 PRECAUTION POUR LES RADIATIONS UV 123456789012345678901234567890121234567890123456 1234567890123456789012345678901212345
EIP-3500 123456789012345678901234567890121234567890123456 123456789012345678901234567890121234567890123456 123456789012345678901234567890121234567890123456 123456789012345678901234567890121234567890123456 123456789012345678901234567890121234567890123456 123456789012345678901234567890121234567890123456 UV-RADIATION PRECAUTION (Continued) 123456789012345678901234567890121234567890123456 123456789012345678901234567890121234567890123456 123456789012345678901234567890121234567890123456 PRECAUTION POUR LES RAD
EIP-3500 WARNING: High brightness light source, do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly in to the beam of light. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO MOISTURE OR WET LOCATIONS. CAUTION The lighting flash with arrowhead within a triangle is intended to tell the user that parts inside the product are risk of electric shock to persons. RISK OF ELECTRIC SHOCK.
EIP-3500 Precautions for using lead-free solder 1 Employing lead-free solder "PWBs" of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder. Example: LFa Indicates lead-free solder of tin, silver and copper. 2 Using lead-free wire solder When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder.
EIP-3500 Operation Manual Projector Top View POWER button Power indicator For turning the power on or putting the projector into standby mode. Lamp indicator Temperature warning indicator Volume buttons KEYSTONE button For entering the Keystone Correction mode. For adjusting the speaker sound level. ZOOM-FOCUS button ENTER button For adjusting the projected image size or adjusting the focus. For setting items selected or adjusted on the menu.
EIP-3500 About the Indicators on the Projector Power indicator Green on ... Normal (Standby) Red on ... Normal (Power on) Lamp indicator Green on ... Normal Green blinks ... The lamp is warming up or shutting down. Red on ... The lamp has been shut down abnormally or needs to be changed. Temperature warning indicator Off ... Normal Red on ... The internal temperature is abnormally high.
EIP-3500 Projector (Rear View) Terminals Refer to “INPUT/OUTPUT Terminals and Connectable Main Equipment” on AUDIO OUTPUT terminal INPUT 3 terminal Audio output terminal of equipment connected to the AUDIO INPUT terminal. Terminal for connecting video equipment. INPUT 4 terminal Terminal for connecting video equipment with an S-video terminal. OUTPUT (INPUT 1, 2) terminal · Shared computer RGB and component signals output terminal for INPUT 1 and 2. · Terminal for connecting a monitor.
EIP-3500 Remote Control POWER button AUTO FOCUS button For turning the power on or putting the projector into standby mode. For adjusting the focus automatically. FOCUS buttons For bringing the projected image into focus. ZOOM buttons For adjusting the projected image size. IRIS button For switching "HIGH BRIGHTNESS MODE" or "HIGH CONTRAST MODE". KEYSTONE button MENU button For entering the Keystone Correction mode. For displaying adjustment and setting screens.
EIP-3500 Front View Remote control sensor Usable Range 30° The remote control can be used to control the projector within the ranges shown in the illustration. 30° Remote control signal transmitters 30° Note The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the signal may differ depending on the screen material.
EIP-3500 Connection Pin Assignments INPUT 1/INPUT 2 and OUTPUT RGB Signal Terminal: 15-pin Mini D-sub female connector RGB Input 11 15 1 6 5 10 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Component Input Video input (red) Video input (green/sync on green) Video input (blue) Not connected Not connected Earth (red) Earth (green/sync on green) Earth (blue) Not connected GND Not connected Bi-directional data Horizontal sync signal: TTL level Vertical sync signal: TTL level Data clock 1. 2. 3. 4.
EIP-3500 DIMENSIONS Units: inches (mm) Side View /16 (1.5) Rear View Side View 9 /64 (3.5) 11 7/64 (282) 1 Top View 12 7/32 (310) 2 3/16 (55.5) 3 33/64 (89) 13/64 (5) Front View 1 59/64 (48.5) 2 11/64 (55.05) 3 15/16 (99.95) 5 7/64 5 7/64 (129.5) (129.5) 7 1 5/32 1 /32 (29.1) (30.9) M4 M4 5 9 /16 (14) /8 (15.5) 1 3/4 1 7/32 (44.1) (30.9) 16 8 7/8 (225.3) M4 8 9/32 (210.3) M4 4 3/16 (106.
EIP-3500 REMOVING OF MAJOR PARTS * Before removing the projection lens, set the IRIS setting to “High Contrast”. (See page 25.) 1. Removing the lamp door and the lamp unit 1-1. Loosen the lamp door fixing screw, slide the lamp door in allow direction and lift off the lamp door. 1-2. Loosen 2 lamp unit fixing screws and lift off the lamp unit. Lamp Unit 1-2 Lamp Door 1-1 2. Removing the top body 2-1. 2-2. 2-3. 2-4. 2-5. Insert a postcard or such thick paper under the lens barrel and between the body.
EIP-3500 3. Attaching the top body (For the screws to apply, refer back to "2. Removing the top body".) 3-1. Insert the postcard over the lens barrel. 3-2. Place the top body in position. Make sure the four hooks are tightly caught. 3-3. Draw out the postcard. Top Body 3-2 Bottom Body 3-3 3-1 Thick paper such as postcard 4. Removing the main PWB unit and the peripheral units 4-1. 4-2. 4-3. 4-4. 4-5. 4-6. 4-7. 4-8. 4-9. Remove 2 main PWB fixing screws (terminal side). Remove 8 main PWB fixing screws.
EIP-3500 5. Removing the optical mechanism unit 5-1. Remove the fixing screw for the optical mechanism unit from the bottom body. 5-2. Remove 5 fixing screws for the optical mechanism unit. 5-3. Remove the duct. 5-2 Duct 5-3 Optical Mechanism Unit 5-1 6. Removing the ballast/power supply unit 6-1. Remove 2 fixing screws for the ballast/power supply unit. 6-2. Remove the fixing screw for the ballast/power supply unit (terminal side).
EIP-3500 7. Removing the ballast/power supply unit 7-1. 7-2. 7-3. 7-4. Remove the fixing screw for the rear R/C PWB unit. Remove 4 fixing screws, 4 WH bosses and the edge saddle for the ballast unit. Remove 11 fixing screws and 5 WH bosses for the power supply unit. Remove 4 fixing screws from the exhaust fans and fan guard. 7-3 Power Supply PWB Unit 7-3 7-1 7-3 Rear R/C PWB Unit 7-4 7-3 Power Supply Unit Fan guard 7-2 7-3 Exhaust fans 7-2 7-3 Edge saddle 7-3 Ballast Unit 7-2 8.
EIP-3500 9. Fixing the grounding plate 9-1. 9-2. 9-3. 9-4. 9-5. 9-6. 9-7. Install the four nuts. Fit the reinforcement (bracket A) in position. Place the grounding plate as specified. Fit the reinforcement (bracket B) in position. Tighten up the four M3 screws. Tighten up the four M4 screws. Melt the six pins of the grounding plate.
EIP-3500 RESETTING THE TOTAL LAMP TIMER ● Resetting the Lamp Timer Reset the lamp timer after replacing the lamp. Info Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or explode. 1 AC socket POWER button Connect the power cord. Plug the power cord into the AC socket of the projector. ENTER button 2 " button Reset the lamp timer.
EIP-3500 Maintenance indicator Abnormal Normal Temperature warning indicator Lamp indicator Off Problem The internal Red on temperature is (Standby) abnormally high. Green on Green blinks Red on when the lamp is warming up or shutting down.
EIP-3500 THE OPTICAL UNIT OUTLINE Layout for proper setup of the optical components and parts (top view) (Schematic diagram) Reflection mirror Projection lens Color wheel Lamp Field lens DMD Rod UV Filter Illumination lenses 1 Illumination lenses 2 Item Lamp Color wheel Rod Illumination lenses Reflection mirror Field lens DMD Projection lens Function Light source. DC high-pressure mercury lamp. Splits light from the light source into R, G, B and W through a color filter. Assures uniform light ray.
EIP-3500 Air blow direction Exhaust fans 1 and 2 After replacing the DMD, if shading is present on the screen as shown in Figure 1, adjust the lighting area of the DMD by turning the adjustment screws for the optical engine. 1. Loosen the fixing screw for the adjustment lever 1. Adjust the lighting area by adjustment lever 2 and then tighten the fixing screw for the adjustment lever 1. 2. If the above adjustment is insufficient, loosen the fixing screw 3 and set the adjusting screws 4 and 5.
EIP-3500 ELECTRICAL ADJUSTMENT No. Adjusting point Adjusting conditions Adjusting procedure 1 EEPROM initialization 1. Turn on the power (with the lamp on) and warm up the set for 15 minutes. » Make the following settings. Press S3563 to call the process mode and execute "SS2" on SS menu. 2 Adjustment of CW index 1. Feed 64 STEP color bar or RGB lamp pattern (XGA 60 Hz) to input 1. 2. Select the following group and subject. Group: DLP Subject: Index Delay 1.
EIP-3500 No. Adjusting point Adjusting conditions Adjusting procedure 7 DTV R Contrast adjustment (manual or automatic) 1. Send white/black window pattern signals with 100% (0.7 Vpp)/0% of amplitude level of 480P to input 1. 2. Select the following group and subjects. Group : AD2 Subject : R-Contrast2 (Process GAMMA interlock) 1. Check the fixed value. R-Bright: 63 2. Observe the chroma of 100% white window pattern with CA100. 3. Increase the R-Contrast2 value on the screen with bit dropouts.
EIP-3500 No. Adjusting point Adjusting conditions Adjusting procedure 14 Adjustment of 1. Select the following group 1. Check the fixed value. DVD color saturaand subject. Color : 12 tion Group : DVD Subject : Color 15 Video Bright / Contrast adjustment 1. Select the following group and subjects. Group : VIDEO Subject : Contrast Bright 16 Adjustment of VIDEO Tint 1. Select the following group 1. Check the fixed value. and subject.
EIP-3500 Adjustment when assembling No. Adjusting point 21 Adjustment of DLP voltage Adjusting conditions Adjusting procedure 1. Read voltage rank of DLP description. 2. Set the switch corresponding to the rank which has been read. 1. Carry out adjustment when DLP chip has been replaced or combination of chip and formatter has been changed. Rank: B C D E Setting value: 1 2 3 4 Checkpoints No. Adjusting point Adjusting conditions Adjusting procedure 22 Adjustment of DLP Brightness 1.
EIP-3500 No. Adjusting point 30 Delivery settings Adjusting conditions Adjusting procedure 1. Make the following settings.
EIP-3500 AF (autofocus) inspection < Camera > Required conditions: 1. Place the unit in front of the screen (size: 60-inch diagonal) at the distance of 1.8m. There is no light source such as a fluorescent light or reflector in the background. 2. Focus is adjusted correctly. 3. RGB input of 256-gradation pattern. Method: 1. Send AF inspection command ("_CMR 1"). 2. Check that the response command is "OK". < AF function > Required conditions: 1.
EIP-3500 » Adjustment mode process menu Adjustment mode process menu 1 * Adjust only the shaded items below.
EIP-3500 Adjustment mode process menu 2 second layer VERSION Build Boot Code Config RomCode GUI DLP AF Unit LAN EXIT SS SS2 SS3 EU SS4 US SS5 JPN SS6 CHIN EXIT TEMP Temp1 Temp2 EXIT OPTION Pixel Gamma DLP Gamma EXIT LAMP Current Time History1 History2 History3 History4 TOTAL TIME EXIT LINE OFF LED CHECK Calibration K-Senser EXIT Initial Value Parameter of sensor1 Parameter of sensor2 Standard RGB 4 Current time of use One Earlier Two Earlier Three Earlier Four Earlier Total operating hours 33
EIP-3500 TROUBLESHOOTING TABLE Checking the basic operation Does the power LED light up or flash in red or green? NO Go to "Checking the power supply system". YES Does the set function with its keys or the remote controller? NO Go to "Checking the peripheral circuits of the microprocessor". YES Does the cooling fan rotate, and the lamp turn on? NO Go to "Checking the lamp light-up". YES Is the user menu displayed? NO Go to "Checking the peripheral circuits of the formatter".
EIP-3500 Checking the power supply system Is 13V output to pins (9) and (11) of P1707? NO Go to "Checking the power unit". YES Is 6V output to pins (1) and (3) of P1707? NO Go to "Checking the power unit". YES Is the connector of P1708 fully inserted? NO Is the voltage of 6V applied to both ends? Replace the thermal fuse. YES NO Check IC1776 and peripheral circuits. Is B+5VAT output from IC1776? YES NO Check IC1708 and peripheral circuits. Is BU+3.
EIP-3500 Checking the power unit Is each connector of the power unit fully inserted? NO Securely insert the connectors. YES Is the lamp door closed completely? NO Fix the lamp door with screws. YES Is the bimetal broken? NO Replace the bimetal switch or restore by pressing the red button. NO Replace F701. If other parts are damaged, replace them. NO Check D707 and the peripheral circuits of IC702 on the primary side. If defective, replace them.
EIP-3500 Checking the peripheral circuits of the microprocessor Are the voltages of approx. 3.3V and 2.5V applied to both ends of C2030 and C2029 respectively? NO Go to "Checking the power supply system". YES Are the oscillations of 133MHz and 64MHz output from pin (3) of X2001 and pin (3) of X2002 respectively? NO Check the peripheral circuits of X2001 and X2002. YES Does each terminal of R2039, R2040, R2042, R2048 and R2050 change? NO Check IC2201 and IC2202. IC2003 is defective.
EIP-3500 Checking the lamp light-up Does each cooling fan function? NO Check the power supply circuit or fan circuit on the main circuit. YES Is the rotating sound of the color wheel heard? ABNORMAL NO YES Check IC9102, 9003 and the peripheral circuits of the motor driver IC IC9101. Go to "Checking the peripheral circuits of the formatter". NORMAL Replace the color wheel. Is the discharging sound heard? YES Is the lamp tight in the socket? NO Replace the lamp.
EIP-3500 Checking the peripheral circuits of the formatter What is the screen problem? The rainbow-like screen is displayed. Each color (R, G and B) does not match. The screen is all black. The problem remains even after adjusting "Process menu", "DLP" and "Index". Is the socket of SC9001 connected properly? Thick and white vertical lines (flash).
EIP-3500 Checking the RGB input Send RGB signals to INPUT1 or INPUT2. Use keys on the main unit or remote control to select INPUT1 or INPUT2. NO Are sync signals input to pins (30) and (31) of IC3005? YES Go to "Checking the sync signal".
EIP-3500 Checking the Component Send component signals to INPUT1 or INPUT2. Use keys on the main unit or remote control to select INPUT1 or INPUT2. YES Is picture signal including sync signal input to pin (46) of IC3002? YES 2 NO Are picture signals input to pins (8), (9) and (10) of IC3101? NO Check IC4003, IC4004 and peripheral circuits.
EIP-3500 Checking of Video input Send composite VIDEO signals to INPUT3. Use keys on the main unit or remote control to select INPUT3. Is picture signal input to pin (1) of IC3103? NO Check the VIDEO-IN signal line of Q3104 and soldering of J3101. YES Check the peripheral circuits of C3103 and color system malfunctions. YES Is input signal SECAM? NO NO Are picture signals input to pins (39) and (41) of IC3103? YES Check IC3105 and peripheral circuits.
EIP-3500 Checking of Sync signal NO Check IC4008 and peripheral circuits. Are HV sync signals sent to pins (1) and (6) of IC4010? YES NO IC4008 and IC4010 are defective. Are HV sync signals sent to pins (22) and (23) of IC3002? YES Are sync signals sent to pins (28) and (29) of IC3002? NO Is a clock of 27MHz sent to pin (42) of IC3002? Do signals of pins (21) and (22) of IC3002 change? YES Check IC3002 and peripheral circuits. NO IC3005 and peripheral circuits are defective.
EIP-3500 Checking the autofocus Is dust, dirt or damage present on the auto focus sensor cover? NO Remove the dust and dirt, or replace. YES NO Are voltages of 3.3V, 1.5V and 2.8V applied to pin (4) of X5001, pin (94) of IC5003 and pin (5) of IC5008 respectively? Check the power supply circuit and its peripheral circuits. YES NO X5001 is defective. Is a clock (49MHz) output from pin (3) of X5001? YES Is a clock (12.
EIP-3500 Checking the LAN LAN communication is disabled even though connecting the control PC with a LAN cable. The LINK LED (green) does not light up. YES Are the connection of connecting cable and the settings of IP address, sub-net address and default gateway correct? NO YES Check the connecting cable and LAN settings. If the LAN settings are unknown, contact the network administrator. If the network settings cannot be saved, replace IC8003 (EEP ROM) as it may be defective.
EIP-3500 Checking RS-232C Communication is disabled even though connecting the control PC and projector with a RS-232C cable. YES Is the connecting cable connected correctly? (cross cable) NO Replace the connecting cable. YES NO Does pin (8) of IC8002 receive a signal? Check R8002 and the peripheral circuits of SC8001. YES NO Check the peripheral circuits of IC8002.
EIP-3500 Resetting after replacing IC8003 (EEP ROM) MAC address returns to default. Follow the steps below to reset. 1 Open the top cabinet of the projector and confirm the MAC address (MAC: ************) of the seal on the PWB. 2 Connect the control PC and projector with a RS-232C cable. 3 Turn on the AC power supply. 4 EEP ROM returns to default. 5 Turn off the AC power supply and turn on again. 6 Set MAC address by using the RS-232C command. (Refer to "MAC address setting" for the setting procedure.
EIP-3500 CHASSIS LAYOUT H G F E D FORMATTER UNIT DUNTKC613WEF0 C POWER UNIT RDENCA118WJZZ B A 1 2 3 4 5 6 48 7 8 9 10
EIP-3500 FRONT R/C RECEIVER UNIT DUNTKC615WEF3 MAIN UNIT DUNTKC612WEF3 BALLAST UNIT RDENCA088WJZZ REAR R/C RECEIVER UNIT DUNTKC681WEF3 10 11 12 13 14 15 49 16 17 18 19
EIP-3500 BLOCK DIAGRAM H G F E D C B A 1 2 3 4 5 6 50 7 8 9 10
EIP-3500 10 11 12 13 14 15 51 16 17 18 19
EIP-3500 OVERALL WIRING DIAGRAM H G F E D C B A 1 2 3 4 5 6 52 7 8 9 10
EIP-3500 10 11 12 13 14 15 53 16 17 18 19
EIP-3500 WAVEFORMS 1 IC3101 (28) pin (VS-OUT) H : 4m sec/div V : 1V/div 2 IC3101 (29) pin (HS-OUT) H : 20µ sec/div V : 1V/div 3 IC3101 (31) pin (SCP-IN) H : 20µ sec/div V : 1V/div 4 IC3101 (35) pin (R-OUT) H : 10µ sec/div V : 500mV/div 5 IC3101 (37) pin (G-OUT) H : 10µ sec/div V : 500mV/div 6 IC3101 (39) pin (B-OUT) H : 10µ sec/div V : 500mV/div 7 IC3103 (43) pin (C2-IN) H : 10µ sec/div V : 500mV/div 8 IC3103 (44) pin (CVBS/Y2-IN) H : 10µ sec/div V : 500mV/div 9 IC3105 (7) pin (YCIN) H : 10µ sec/d
EIP-3500 PRINTED WIRING BOARD ASSEMBLIES H G F FRONT R/C Unit (Side A) FRONT R/C Unit (Side B) REAR R/C Unit (Side A) REAR R/C Unit (Side B) E D C B A 1 2 3 4 55 5 6
EIP-3500 H G F E D C B A MAIN Unit (Side-A) 1 2 3 4 5 6 56 7 8 9 10
EIP-3500 10 11 12 13 14 15 57 16 17 18 19
EIP-3500 H G F E D C B A MAIN Unit (Side-B) 1 2 3 4 5 6 58 7 8 9 10
EIP-3500 10 11 12 13 14 15 59 16 17 18 19
EIP-3500 H G F E D C B FORMATTER Unit (Side-A) A 1 2 3 4 60 5 6
EIP-3500 H G F E D C B FORMATTER Unit (Side-B) A 1 2 3 4 61 5 6
EIP-3500 H G F E D C B A POWER BALLAS Unit (Side A) 1 2 POWER BALLAST Unit (Side B) 3 4 62 5 6
E IP -3500 R ef. No. PA R T S L IS T Part No. Des c ription C ode R ef. No. MA IN UNIT P arts marked with " " are important for maintaining the s afety of the set. B e sure to replace these parts with specified ones for maintaining the s afety and performance of the s et.
EIP-3500 Ref. No. Part No.
EIP-3500 Ref. No. ★ Part No. Description Code Ref. No.
EIP-3500 Ref. No. Part No. ★ Description Code Ref. No.
EIP-3500 Ref. No. Part No. ★ Description Code Ref. No.
EIP-3500 Ref. No. ★ Part No.
EIP-3500 Ref. No. Part No. ★ Description Code Ref. No.
EIP-3500 Ref. No. Part No. ★ Description Code Ref. No.
EIP-3500 Ref. No. Part No.
EIP-3500 Ref. No. ★ Part No.
EIP-3500 Ref. No. Part No. ★ Description Code Ref. No. ★ Part No.
EIP-3500 Ref. No. Part No. ★ Description Code Ref. No.
EIP-3500 Ref. No. R9532 R9542 R9554 R9559 R9560 R9562 R9565 R9567 R9569 R9574 R9575 R9592 R9594 R9595 R9596 R9597 ★ Part No. Description Code Ref. No. ★ Part No.
EIP-3500 Ref. No. ★ Part No. Description Code Ref. No.
EIP-3500 Ref. No. Part No. ★ Description Code Ref. No.
EIP-3500 Ref. No. Part No. ★ Description Code Ref. No.
EIP-3500 CABINET AND MECHANICAL PARTS H 1 G Z 1-1 1-3 37 1-2 23-1 F 1-5 E D G F H 23-3 23-2 37 23 58 37 23-1 37 a Q 51 V R 41 N M Y L O E b 26 D A P 52 E K 61 V A J X I 61 P 28 4 D 46 29 36 27 40 J 33 a 53 B 24 61 61 47 35 å 2-10 C 50 C B 45 2-17 54 2-1-10 61 2-10 2-17 I 2-1-4 C 2-3 2-1-2 2-8 61 2-1-1 31 57 57 37 2-7 62 Z X 2-1-9 b 2-1-3 61 K 2-1-5 2-11 B 2-16 2-17 2-14 3 2-14 3-4 2-11 2-9 25 30 2-1 2-2-4 3-1-2 3-2 2-1-7 2-1
EIP-3500 Ref. No. Part No. ★ Description Code Ref. No.
EIP-3500 Part No. ★ Description Code Ref. No. OPTICS MECHANISM PARTS Ref. No. ★ Part No.
EIP-3500 Ref. No. Part No. ★ Description Code Ref. No. GCASNA018WJSA QACCDA010WJPZ å QACCVA011WJPZ QCNWGA014WJPZ QCNWGA043WJPZ QCNWGA045WJPZ RRMCGA371WJSA TCAUZA170WJZZ TLABV0003SEZZ TLABVA333WJZZ TiNS-B671WJZZ TiNS-B672WJZZ TiNS-B673WJZZ TiNS-B674WJZZ TiNS-B675WJZZ TiNS-B676WJZZ TiNS-B723WJZZ UDSKAA060WJZZ QCNWGA015WJPZ ★ Description PACKING PARTS (NOT REPLACEMENT ITEM) SUPPLIED ACCESSORIES å Part No. Soft Case Power Cord for U.S., Canada, etc. Power Cord for Europe, except U.K.
EIP-3500 Ref. No. ★ Part No. Description Code No. Part No. PACKING OFRef. THE SET Description Code Operation Manual (TiNS-B671WJZZ) (English) (TiNS-B672WJZZ) (French) (TiNS-B673WJZZ) (Spanish) QUICK GUID (TiNS-B723WJZZ) CD-ROM (UDSKAA060WJZZ) Polystylene Bag (SSAKAA018WJZZ) Polystylene Bag (SSAKAA018WJZZ) Power Cord for U.S., Canada, etc. (QACCDA010WJPZ) for Europe, except U.K.
EIP-3500
