Table of Contents 1. Safety Instructions ··················································································· 2 2. The Projector ···························································································· 3 2.1 Features 3 2.2 Accessories 4 2.3 Appearance 5 3. Setting up the Projector ·········································································· 6 3.1 How to connect the projector 6 3.2 Turning on/off the projector 8 3.
1. Safety instructions Before you use the projector, please read this manual thoroughly and comply with the safety instructions hereunder. Improper use may cause fire, electric shock, injuries, or reduce the life of your projector. Warning: Please ensure the projector is grounded properly by connecting the power cord to a grounded AC outlet. Do not defect the safety purpose of the grounding type plug. Warning: Do not cover the lens while the lamp lights.
2. The projector 2.1 Features • With the modularized structure of the product, all you need is the main body when conducting a presentation, thereby making your job easier. • XGA model can receive signals with resolution up to 1280x1024. To ensure the output quality, please adjust the setup of your computer display card to be less than or equal to 1280 x 1024. • Compact size, only 3.5 lbs. • Incorporated TI single chip 0.7” DLPTM technology. • Users may replace 150W (VIP R150/E20) lamp easily.
2.2 Accessories Please check if following accessories are in the box. If any items are missing, please contact your dealer immediately.
2.3 Appearance Control panel Outlet Grille Zoom Ring Focus Ring Lens cover Infra Red Remote Receiver Speaker Video Enhanced Adaptor Main Body Screw Warning Do keep the flow out of Outlet Grille free.
Foot Adjuster button Foot Adjuster 3. Setting up the projector 3.1 How to connect the projector Depending on your purpose, you can select any of the following connection methods. 1) For displaying data only Find the M1DA-VGA+USB cable; connect M1DA connector to the main body; and connect VGA and USB connectors to the computer. Then you can start presentation. Under such circumstance, video and audio function won’t be available.
2) For playing video with audio effects Connecting with the Video Enhanced Adaptor; and choose terminals below to connect. 1. Power cord 2. VGA signal in port 3. USB mouse control 4. S-Video signal in port 5.6 Composite Video signal in port 7.8 PC Audio In/Out port Notes Connecting to a Computer 1. Please make sure that both projector and computer are shutdown. 2. Plug USB cable into computer. 3. Plug one end of the VGA cable into the projector.; 4. Plug the other end into the computer. 5.
3.2 Turning on/off the projector Turning on the projector 1. 2. 3. 4. 5. 6. 7. Remove the lens cover. Make sure the signal cables are connected. Plug-in the power cord. LED indicator flashes slowly. Press the Power key on the remote controller or control panel to turn on the projector. LED indicator lights up consistently at this time. The message “Warming up! Please wait.” appears on the screen of the projector. Please wait for 20 seconds, the projector will detect the input signal source automatically.
3.3 Adjusting the altitude of the projected image Foot Adjuster Button Foot Adjuster Please use the foot adjuster to adjust the height of projector. Higher 1. Hold the foot adjuster button. 2. Raise the projector to the height you like; and then release the foot adjuster to fix the projector. Lower 1. Hold the foot adjuster. 2. Lower projector to the height you like; and then release the foot adjuster to fix the projector.
3.4 Adjusting the focus and zoom Zoom Ring Focus Ring You can zoom in or out the image with the zoom ring. To enlarge the image size, please turn the zoom ring counter-clockwise. To reduce the image size, please turn the zoom ring clockwise. To adjust the focus of the image, please turn the focus ring until the image becomes clear. The projection distance of the projector is 1.45 – 10 meters.
3.5 Projected Image Size Projection Distance 1.45M 2.
4. How to use the projector This section covers the methods of using and adjusting the projector, as well as the methods of using the control panel, remote controller and menu. 4.1 Initial image adjustment 1 Please follow the previously stated steps to turn on the projector; and keep the projector facing the screen. 2 Turn the zoom ring to adjust the size of the image. 3 Turn the focus ring to adjust the focus of the image. 4 Use the foot adjuster to adjust the altitude of the image.
LED Indicator When the projector is turned on, the LED indicator flashes. Press the Power key to display the mage. At this time, the LED indicator lights up consistently. If the LED indicator flashes quickly, the projector is probably in an abnormal condition. Possible reasons include: a. If the fan is in an abnormal condition, the message “Fan lock error occurred, Projector going shutdown!” appears on the screen. b.
- Remote controller Functions Key Freeze/Esc/L Enter/R Power Press this key to freeze the image. Press again to clear the static image. Press this key to quit the menu if the menu is on the screen. In the remote-control mouse mode, this key works as the left key of mouse. Please check page 13 “Auto/Enter” of “Control panel” for the use of this key on the menu. In the remote-control mouse mode, this key works as the right key of mouse. Please refer to page 8 “Turning on/off the projector”.
Mode Press this key and green LED indicator turns on. Then the remote controller can be used as a mouse. " Be sure to connect USB mouse cable to the computer and projector before using the remote controller as a mouse. Menu Please refer to page 13 “Menu” of “Control panel”. Source Select Analog RGB, Analog Y Pb Pr, Digital RGB, Composite Video, S-Video and Component Video signals in sequence. Convert the image into blank and fully blue. Press again to restore.
5. Menu Press the Menu key to open the menu. You can press the up or down key to select the items on the menu; or press Esc to quit the menu. To enter the submenu, please press Enter key or right key. On the submenu, press the Menu or Esc key on the remote controller to return to the main menu; or press twice to quit menu. 5.1 Image (VGA mode) Submenu Purpose Using Brightness (**) To adjust the brightness of image Contrast To control the balance between the brightest and darkest parts of the image.
5.2 Image (Video mode) Submenu Purpose Using Brightness To adjust the brightness of image. Contrast To control the balance between the brightest and darkest parts of the image. You can change the amount of black and white. To adjust the balance between red and green colors in the image. Hue Saturation To change the image from black & white to saturated colors. Sharpness To adjust the sharpness of the image. * Press Auto key to return to previous setup. 17 Press key to decrease brightness.
5.3 Display (VGA mode) Submenu Frequency Phase V Position H Position Purpose To adjust the frequency of data display to be the same as the frequency of display card of computer. Please use this function to correct the flickering vertical lines shown in the image. To synchronize the signals of images and display cards. Use this function to correct inconsistent or flickering images. To adjust the vertical position of screen. To adjust the horizontal position of screen.
Proportion To select the aspect ratio of screen, 16:9 or 4:3. Press User Color For end users to adjust red green and blue colors on their own. User Red To adjust the Red color. User Green To adjust the Green color. User Blue To adjust the Blue color. Color Temp To adjust the color temp in the range between 6100K and 9300K. Choose Yes. User Red, User Green and User Blue options appear. Choose No. Only Color Temp option appears. Press key to decrease amount of Red color.
5.4 Display (Video mode) Submenu Purpose Using Keystone To modify the biased image resulting from the improper angle of projector. Proportion User Color To select the aspect ratio of screen, 16:9 or 4:3. For end users to adjust red green and blue colors on their own. Press key to reduce the length of lower screen. Press key to reduce the length of upper screen. (*) Press key for selection. User Red To adjust the Red color. User Green To adjust the Green color. 20 Choose Yes.
User Blue To adjust the Blue color. Color Temp To adjust the color temp in the range between 6100K and 9300K. * Press Auto key to return to previous setup. 21 Press key to decrease amount of Blue color. Press key to increase amount of Blue color. (*) Press key to lower color temp; and the image looks warmer. Press to increase color temp; and the image looks cooler.
5.5 Audio Submenu Volume Treble Bass Mute Purpose or Using Press key to turn down the volume. Press key to turn up the volume. (*) Press key to decrease the volume of treble. Press key to increase volume of treble. (*) To adjust the medium/low frequency of audio. Press key to decrease bass. Press key to increase bass. (*) Select ”Yes” for Mute. * Press Auto key to return to previous setup.
5.6 Management Submenu Purpose OSD Location To display the position of menu on the screen. Projection (Projection before the Screen) Default Using Press key for selection (*) Press key for selection (*) (Projection behind the Screen) If you select this function, the projector will reverse images from left to right or vice versa. Thus the image can be projected from behind onto the semi-transparent screen. Lamp Remind To remind you of the number of hours that the lamp has been lit up.
Lamp Reset To recount hours after replacing the lamp. Auto Adjust For end users to fix the brightness and contrast settings. This function only works in the VGA mode. Reset All To return to the factory default. Source Type To select RGB, Composite, Component, HDTV(**),S-Video, signals or Auto Scan. Press the right key. The message “Press Enter key to confirm lamp reset operation!” appears. Please check if the user has replaced the new lamp. If yes, press Enter key.
6.1 Replacing the lamp 30 hours before the end of the lamp’s life time, the warning message “Lamp life time is up! Replacement suggested!” will display on the screen. Please replace the lamp immediately. Steps: 1. Power off the projector. 2. Unplug the power cord. 3. Cool down projector for at least 30 minutes. 4. Use a screwdriver to remove the shell and screws on the lamp. 5. Remove lamp. 6. Gently process the new lamp module into the lamp bay, then replaces the lamp module retaining screws. 7.
7. Appendix 7.1 Common problems and trouble-shooting If you are having a problem with your projector, please check the following: If you still cannot solve the problem, please contact your local distributor or our service center. Q.: No image on the screen at all? Make sure that you have properly connected the video enhanced adapter and the relevant cables mentioned in previous chapters. Make sure the plug is not bended or broken. Please check if the lamp has been installed properly.
Q.: Image becomes blurred Adjust the focus ring of the projector. Make sure that distance between the screen and projector is adequate (1.45~10m) Q.: The colors projected by your projector look different from the colors of your computer or VCR. This is not a problem. You can adjust the brightness, color or contrast on the menu to change colors. Q.: When the projector is connected to a DVD player, playing a film with the ratio 16:9, the image is reshaped. Adjust the aspect ratio of the projector to 4:3. Q.
7.2 Specifications EIP-1 Model No. Resolution XGA (1024*768) Size 229 x 193 x 69 mm Weight 3.5 lbs Lamp 150W VIP Brightness 1400 Lumens Projection distance 1.45m ~10m Throw Ratio 1.34:1 ~ 1.6:1 (Distance: Diagonal) Zoom Ratio 1.2:1 (Manual Zoom/Focus) Uniformity 85% Aspect Ratio 4:3 / 16:9 screen selectable Contrast Ratio 900:1 Horizontal Frequency 31.
Input Terminal DVI (M1DA) USB RGB (M1DA-D-Sub 15 pin) RS232 (M1DA) YPbPr (M1DA,VGA) S-Video Mini DIN 4 pin Audio: RCA Jack 3.5mm Mini Jack Composite Video (RCA Jack) Output Terminal 1 watt speaker * All specifications are subject to change without notice. This device complies with Part 15 of the FCC Rules.
