User's Manual

ManualsBrandsEicon Networks ManualsOtherD/120JCT-LSU

4. Insert the board's edge connector into the bus

slot. Apply pressure only to the top edge of the

board, and gently rock the board forward and

backward to seat the edge connector into the

slot.

5. Install the retaining screw.

6. If installing multiple boards, select a new slot and

repeat steps 3 through 5 for each board you are

installing.

Connecting the CT Bus Cable

For the D/120JCT-LSU board to interoperate with

other telecom boards in the system, the boards

must be interconnected using a cable. The D/

120JCT-LSU board has an H.100 CT Bus connector,

which may be directly connected to other CT Bus

boards with an appropriate CT Bus cable. The D/

120JCT-LSU board can also interconnect with

SCbus boards by means of a CT Bus to SCbus

adaptor.

A CT Bus cable is not included with the D/120JCT-

LSU board. You must order an appropriate cable as

an accessory item. CT Bus cables are available in a

variety of configurations to accommodate different

numbers of interconnected boards. Always use a

cable that closely matches the number of boards

you are actually using; avoid using a cable that is

longer than necessary for your particular system. If

Installing a PCI Board

ISA Slot

PCI Slot

PCI

Board

Computer

Chassis

Remove

Cover

Plate

the cable is longer than necessary, connect it to the

boards so that all the unused connectors are at one

end of the cable.

Installing a CT Bus/SCbus Adapter

To connect a the D/120JCT-LSU board to one or

more boards that are interconnected via SCbus, you

must use an optional CT Bus to SCbus adapter. This

adapter assembly is installed on the CT Bus board

that is physically closest to the SCbus boards; only

one adaptor is used per system.

Refer to the documentation shipped with the adaptor

for more information on proper installation.

Completing the Installation

After installing all the boards required for your

system and interconnecting them with appropriate

cables, replace the cover on the computer to

complete the installation.

5. Connecting to External

Equipment

Each of the six RJ-14 jacks on the rear bracket of

the the D/120JCT-LSU board supports two analog

telephony channels. A standard telephone will not

function when directly connected to the board.

Note: The RJ-14 jacks use 2 tip/ring pairs with 2

earth recalls, one for each channel.

Note:

Your CT Bus cable may

have a different number

of connectors (drops).

CT Bus

Cable

Installing the CT Bus Cable

Colored

Stripe

(Pin 1)

6. After Installing the Board

After you install the D/120JCT-LSU board and any

other Dialogic

boards, you can proceed with the

following activities:

■

Installing the software - Install the Dialogic

system release software as described in the

Software Installation Guide for your system

release.

■

Configuring the software - Configure the system

release software as described in the

Configuration Guide(s) for your system release.

■

Testing the board - Test the D/120JCT-LSU board

as described in the diagnostics documentation for

your system release.

■

Troubleshooting problems - The administration

and diagnostics guides for your system release

provide information on troubleshooting problems.

■

For technical specifications and product

information go to: http://www.dialogic.com/

products.htm.

7. Removing the Board

Removal of the board is a straightforward process.

Remove the board using the reverse of the

procedure described in Section 4, Installing the

Board above.

8. Warranty and Return

Information

Warranty Period

For specific warranty information for this board, refer

to the Warranty section of the Products page,

located at this URL: http://www.dialogic.com/

warranties/.

Line 2 Earth Recall

Line 2 Ring

Line 1 Tip

Line 1 Ring

Line 2 Tip

Line 1 Earth Recall

Pinout for RJ–14 Jacks on D/120JCT-LSU Bracket

Contacting Technical Support

Dialogic provides technical support for its products

through a network of value added distributors who

are trained to answer technical questions on

installing and configuring Dialogic® products. If you

are unsure how to contact your support channel,

please call Dialogic in the United States at 973-967-

6600 (9am-5pm EST) and we will assist in obtaining

the appropriate support channel.

Outside the United States please refer to http://

www.dialogic.com/support/contact to obtain local

contact information. Dialogic also provides direct

support via Dialogic

Pro™ Services agreements.

For more details of direct support from Dialogic

please refer to:http://www.dialogic.com/support/

DialogicPro

Returning a Product

To return a board for warranty repair or any other

returns, please refer to the following: http://

www.dialogic.com/support/hwfaults.

9. Sales Assistance

If you have a sales question, please contact your

local Sales Representative or the Regional Sales

Office for your area. Address, telephone and fax

numbers, are available at the Dialogic website

located at: http://www.dialogic.com/contact.htm.

To purchase Dialogic® products, please refer to the

following website to locate the appropriate supplier:

http://www.dialogic.com/purchase.htm.

All contents of this document are furnished for informational use

only and are subject to change without notice and do not represent

a commitment on the part of Dialogic Corporation or its subsidiaries

(“Dialogic”). Reasonable effort is made to ensure the accuracy of

the information contained in the document. However, Dialogic does

not warrant the accuracy of this information and cannot accept

responsibility for errors, inaccuracies or omissions that may be

contained in this document.

INFORMATION IN THIS DOCUMENT IS PROVIDED IN

CONNECTION WITH DIALOGIC® PRODUCTS. NO LICENSE,

EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO

ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY

THIS DOCUMENT. EXCEPT AS PROVIDED IN A SIGNED

AGREEMENT BETWEEN YOU AND DIALOGIC, DIALOGIC

ASSUMES NO LIABILITY WHATSOEVER, AND DIALOGIC

DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY,

RELATING TO SALE AND/OR USE OF DIALOGIC PRODUCTS

INCLUDING LIABILITY OR WARRANTIES RELATING TO

FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY,

OR INFRINGEMENT OF ANY INTELLECTUAL PROPERTY

RIGHT OF A THIRD PARTY.

Dialogic products are not intended for use in medical, life saving,

life sustaining, critical control or safety systems, or in nuclear facility

applications.

It is possible that the use or implementation of any one of the

concepts, applications, or ideas described in this document, in

marketing collateral produced by or on web pages maintained by

Dialogic may infringe one or more patents or other intellectual

property rights owned by third parties. Dialogic does not provide

any intellectual property licenses with the sale of Dialogic products

other than a license to use such product in accordance with

intellectual property owned or validly licensed by Dialogic and no

such licenses are provided except pursuant to a signed agreement

with Dialogic. More detailed information about such intellectual

property is available from Dialogic’s legal department at 9800

Cavendish Blvd., 5th Floor, Montreal, Quebec, Canada H4M 2V9.

Dialogic encourages all users of its products to procure all

necessary intellectual property licenses required to implement

any concepts or applications and does not condone or

encourage any intellectual property infringement and

disclaims any responsibility related thereto. These intellectual

property licenses may differ from country to country and it is

the responsibility of those who develop the concepts or

applications to be aware of and comply with different national

license requirements.

Dialogic, Diva, Eicon, Eicon Networks, Eiconcard, Dialogic Pro and

SIPcontrol, among others, are either registered trademarks or

trademarks of Dialogic. Dialogic's trademarks may be used publicly

only with permission from Dialogic. Such permission may only be

granted by Dialogic’s legal department at 9800 Cavendish Blvd.,

5th Floor, Montreal, Quebec, Canada H4M 2V9. Any authorized

use of Dialogic's trademarks will be subject to full respect of the

trademark guidelines published by Dialogic from time to time and

any use of Dialogic’s trademarks requires proper

acknowledgement. The names of actual companies and products

mentioned herein are the trademarks of their respective owners.