Eiconcard C3x Family for Type II PCMCIA Bus www.eicon.
Second Edition (January 2002) 203-049-02 Eicon, Eiconcard, and the Eicon logo are either trademarks or registered trademarks of Eicon Networks Corporation. Changes are periodically made to the information herein; these changes will be incorporated into new editions of the publication. Eicon Networks may make improvements and/or changes in the products and/or programs described in this publication at any time. Copyright © 1996-2002 Eicon Networks Corporation.
Table of Contents Introduction ................................................................... 5 Installing the Eiconcard C3x.......................................... 6 Making an ISDN Connection......................................... 8 Termination ..................................................................... 10 Making a VHSI Connection ......................................... 12 Interface Specifications................................................... 12 The V.24 DCE Interface ...........
www.eicon.
Introduction The Eiconcard C3x is a Type II PCMCIA Release 2.1-compliant card that offers X.25 through a V.24 serial port at speeds of up to 64 Kbps, and/or through an ISDN BRI port (Eiconcard C31) at speeds of up to 128 Kbps (over the “D” channel or the “B” channels). Note The Eiconcard C3x also supports protocols such as SDLC, PPP, and Frame Relay.
Installing the Eiconcard C3x To install the Eiconcard C3x in your PC, you must insert it into the PC’s PCMCIA slot, and then connect the appropriate cable. 1 Install the Eiconcard C3x Insert the Eiconcard C3x into the PC’s PCMCIA slot as shown in Figure 1. To connect the cable to the card, position it with the embossed arrows on the cable connector facing up. Push it straight into the port on the card, and push the locking tab on the cable connector toward the PC. Figure 1.
4 Connect to the outside world You are now ready to connect the Eiconcard C3x to the outside world. • To set an ISDN connection, see ‘Making an ISDN Connection’ on page 8. • To set up a VHSI connection, see ‘Making a VHSI Connection’ on page 9.
Making an ISDN Connection Note Only the Eiconcard C31 supports ISDN connections. After you have installed your Eiconcard C31, connect your ISDN line. In Europe and most countries worldwide In Europe as well as most countries outside of North America and Japan, your Eiconcard C31 adapter can be connected directly to your ISDN line using the included cable. Figure 2 shows how the ISDN S/T2 Interface Cable, and the RJ-45 plug connect together.
Making a VHSI Connection The Eiconcard C3x can connect as a DTE to devices such as Data Service Units (DSUs) which supports V.24, using the included Eicon Networks cable (part #300-084) Consult the documentation which came with your networking software for more information about port configuration. Interface Specifications The standards compliant with the V.24 interface are listed, below: Standard Compatibility CCITT V.24 Signaling CCITT V.28 Electrical CCITT X.
The V.24 DCE Interface A pin-out diagram for the V.24 DCE interface is shown in Figure 3. The signal definitions and names are listed in Table 2. 1 PG N D TXD RXD RTS CTS DSR SG N D DCD 14 TCLK RCLK TEST DTR RLB RI DTECLK TI 25 13 Figure 3. V.
Technical Specifications Technical Data • Type II PCMCIA Release 2.1 compliant Eiconcard CPU/Memory/Flash Eiconcard C30 15.36 MHz Motorola 68302 / 512 KB RAM / 512 KB Flash # of VHSI Ports #of ISDN BRI Ports 1 N/A Eiconcard C31 15.36 MHz Motorola 68302 / 512 KB RAM / 512 KB Flash 1 1 Hardware Installation • Automatic configuration of interrupt request level setting and I/O address External Interface Eiconcard External Interface Cables Eiconcard C30 V.24 (EIA RS-232-C) • V.
International Regulatory Information Regulatory Information for the USA: WARNING. Changes or modifications to this unit not expressly approved by Eicon Networks Corporation could void the user's authority to operate the equipment.
FCC Part 68 Notice This unit complies with Part 68 of the FCC rules. On the bottom of this equipment is a label that contains, among other information, the FCC registration number. If requested, this information must be provided to the telephone company. An FCC compliant telephone cord and modular plug is provided with this equipment, designed to be connected to the telephone network or premises wiring using a compatible modular jack which is Part 68 compliant.
Regulatory Information for Canada NOTICE: The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements. Industry Canada does not guarantee the equipment will operate to the user’s satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company.
Regulatory Information for Europe EU Declaration of Conformity EN: Eicon Networks Corporation declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. DE: Eicon Networks Corporation erklärt, daß diese Telekommunikations-endeinrichtung den grundlegenden Anforderungen und anderen relevanten Bestimmungen der Richtlinie 1999/5/EG entspricht.
203-049-02
