• CEILING FAN OWNER'S MANUAL • Read and Save These Instructions • Casou • 203215A 203217A
TOOLS AND MATERIALS REQUIRED Philips screw driver Blade screw driver 11 mm wrench Step ladder Wire cutters PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: a. b. c. d. e. f. g. h. i. j. k. l. m.
SAFETY RULES 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 8. Avoid placing objects in the path of the blades. 9. To avoid personal injury or damage to the fan and other items, be cautious when working around or cleaning the fan. 2. All wiring must be in accordance with the National Electrical Code and local electrical codes. 10.
MOUNTING OPTIONS If there isn't an existing UL/CUL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials. The outlet box and its support must be able to fully support the moving weight of the fan (at least 35 lbs). Do not use plastic outlet boxes.
HANGING THE FAN REMEMBER: to turn off the power. Follow the steps below to hang your fan properly: Ceiling hanger bracket Step 1. Remove the decorative canopy bottom cover from the canopy by turning the cover counter clockwise. (Fig. 5) Ceiling canopy Step 2. Remove the hanger bracket from the canopy by removing the 1 of 2 screws from the bottom of the hanger bracket and loosening the other one a half turn from the screw head.
MAKE THE ELECTRIC CONNECTIONS WARNING: To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. Code switch NOTE: This remote control unit is equipped with 16 code combinations to prevent possible interference from or to other remote units. The frequency switches on your receiver and transmitter have been preset at the factory.
Step 4. (Figure 11) If your outlet box has a ground wire (green or bare copper) connect it to the fan ground wires; otherwise connect the hanging bracket ground wire to the mounting bracket. Secure the wire connection with a plastic nut provided. After connecting the wires, spread them apart so that the green and white wires are on one side of the outlet box and black and blue wires are on the other side. Carefully tuck the wire connections up into the outlet box.
ATTACHING THE FAN BLADES Step 1. Attach the blade to the blade bracket using the screws and fiber washers as shown in Figure 13. Start screw into bracket. Repeat for the remaining screws. Step 2. Tighten each screw. Make sure the blade is straight. Screws Fiber washers Blade Blades bracket Fig. 13 INSTALLATING THE MOUNTING PLATE Step 1. Remove the 1 of 3 screws from the mounting ring and loosen the other 2 screws. (Do not remove) Step 2.
INSTALLING THE LED LIGHT KIT NOTE: Before starting installation, disconnect the power by turning off the circuit breaker or removing the fuse at fuse box. Turning power off using the fan switch is not sufficient to prevent electric shock. Step 1. Remove the 1 of 3 screws from the posts of the mounting plate and keep it for future use. Loosen the other 2 screws. (Do not remove) (Fig. 16) Step 2. Raise and hold the LED light kit close to the mounting plate and proceed to do the wire connections.
INSTALLING THE BATTERY 9V Ba olt tte ry Install 9 volt battery (included), to prevent damage to transmitter, remove the battery if not used for long periods. (Fig. 17) Fig. 17 OPERATING YOUR TRANSMITTER Restore power to ceiling fan and test for proper operation. 1. HI, MED, and LOW buttons: These three buttons are used to set the fan speed as follows: HI= high speed Med= medium speed Low= low speed 2. OFF button: This button turns the fan off. 3.
OPERATING YOUR TRANSMITTER (CONTINUED) The Reverse switch is located on the top of the motor housing. Slide the switch to the Left for warm weather operation. Slide the switch to the Right for cool weather operation. Speed settings for warm or cool weather depend on factors such as the room size. Ceiling height, number of fans and so on. NOTE: Wait for fan to stop before changing the setting of the slide switch. Warm weather - (Forward) A downward airflow creates a cooling effect as shown in Fig. 19.
CARE OF YOUR FAN Here are some suggestions to help you maintain your fan 1. Because of the fan's natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.) 2. Clean your fan periodically to help maintain its new appearance over the years. Use only a soft brush or lint-free cloth to avoid scratching the finish.
TROUBLESHOOTING Problem Solution Fan will not start. 1. Check circuit fuses or breakers. 2. Check line wire connections to the fan and switch wire connections in the switch housing. CAUTION: Make sure main power is off. 3. Check to make sure the dip switches from the transmitter and receiver are set to the same frequency. Fan sounds noisy. 1. Make sure all motor housing screws are snug. 2. Make sure the screws that attach the fan blade bracket to the motor hub is tight. 3.
SPECIFICATIONS Fan Size 52" Volts Amps Watts RPM CFM N.W. G.W. C.F. Low 120 0.23 11.84 64 1947 120 0.55 65.53 165 5036 19.00 lbs 22.11 lbs 2.52' High Speed These are approximate measures. They do not include Amps and Wattage used by the light kit.
EGLO USA 1-877-892-0007 info.usa@eglo.com EGLO CANADA 1-866-492-3456 info-canada@eglo.
