Owner's Manual
USING
THE
WIRING
KIT
'
POWER/GROUND CABLE (Wiring diagram next page)
1.
Remove seat to gain access to battery. On some models, a tray with the electronics control unit must also be
removed. (Consult factory service manual for steps that are specific to your year/model.)
2. Make sure there is NO fuse in the waterproof fuse holder. Remove
if
necessary.
3. Unscrew the Positive(+) Battery terminal, connect the BLUE ring terminal end and re-connect the terminal.
4. Unscrew the Negative(-) Battery terminal, connect the BLACK ring terminal end and re-connect the terminal.
5. Locate the in-line fuse holder where it can be accessed later to install (or replace) fuse. Fuse holder should be
fastened using the built-in slots and supplied cable ties (See fuse holder diagram Pg.
4)
6. Lift
or
remove gas tank to route power/ground braided cables along with existing wiring. (Consult factory service
manual
for
steps that are specific to your year/model.) Use the supplied cable ties to fasten the braided
power/ground cable securely underneath the tank (either to existing loom
or
withing protective wire trough
if
equipped).
7. Continue to routing towards front area (stereo source unit) behind the fairing.
8.
Cut cables to appropriate length
to
reach amplifiers Power/Ground connections.
9. Slip the matching BLUE/BLACK
PVC
boots over the ends
of
the Power/Ground cables. Strip 1/2"
of
cable insulation
away and discard. Insert stripped copper cable inside the 8/10AWG spade terminals and crimp securely. Slide the
protective PVC boots up over the exposed metal connectors.
REMOTE WIRE (Wiring diagram next page)
AFTERMARKET STEREO:
1.
When installing with an Aftermarket radio, connect the 18GA Blue remote wire to Stereo's Blue/White Remote
output wire.
2. Cut wire to length, strip back 1/4" insulation and crimp the RED 18-22AWG Spade terminal to the amplifier
side
of
the wire.
3. Secure the wire with the supplied cable ties and connect to the "REM" remote input terminal at the amplifier.
NON AFTERMARKET STEREO:
1. When installing to an existing stereo without a Blue/White "amp remote" wire, remote power can be carefully
tapped behind the +12V cigarette lighter.
2. Locate the switched power lead at the back
of
the the lighter socket (typically Orange/White). Use a volt/ohm
meter to verify the connection.
3. Use the included 18-22AWG Butt connector to tap into the switched power lead.
4. Follow steps #2 and #3 above.
SPEAKER LEADS (Wiring diagram next page)
TIP: The cable has printing on 1
of
2 leads. At your convnenience, chose the printed side for
either
the{+)
or(-)
connections. Maintain consistency between the amp and speaker
for+/-
connections
or speakers will be out
of
phase.
1. Determine the length
of
each 16AWG speaker cable needed to reach between the amplifier Left and Right
speaker outputs to each speaker. (Cut excess wire length from ends which are
not
covered in protective braid.)
2. Split and strip back 1/4" insulation from the Speaker side
of
the cable. Crimp on the supplied Blue Female
14-16AWG Speaker terminals and connect to
the(+)
and(-)
terminals
at
the speaker.
3. Split and strip back 1/4" insulation from the Amplifier side
of
the cable. Crimp on the supplied Blue Spade
14-16AWG Speaker terminals and connect to
the(+)
and(-)
outputs at the amplifier.
4. Repeat Step #3 for remaining speaker and use the supplied cable ties to secure cable away from suspension
or
moving parts.
LIMITED
WARRANTY
The manufacturerwarrants this product
to
be
free from defects in material and workmanship for a period
of
1 Year from date
of
purchase. All products are sold with the understanding that the purchaser has independently determined the suitability
of
such products. This warranty does not
cover
any
expenses incurred in the removal and reinstallation
of
the product. This warranty is
offered
to
the original purchaser
of
the product only.
This warranty does not apply to the product which has been damaged by accident,
or
which has been misued, altered,
or
installed
improperly.
If
the product should prove defective within the warranty period, return the product with sales slip, postage prepaid to
Scosche Industries, Inc. Your dated sales slip/proof
of
purchase will establish your warranty eligibility. Scosche,
at
its option, will
replace
or
repair the product free of charge and return the product to you postage paid. In
no
event shall Scosche
be
responsible for
claims beyond the replacement value
of
the defective product
or
in any way be held liable
or
responsible
for
consequential
or
incidental
damages.
No
express warranties and no implied warranties, whether for fitness
or
any particular use,
or
otherwise, except as set forth above
(which is made expressly in lieu
of
all other warranties) shall apply to the products.
2