SpeedStream 5200 Series DSL Bridge Quick Start Guide Part Number: 222-00925-01
SpeedStream 5200 Series Bridge Copyright 2000, Efficient Networks, Inc. All rights reserved. Printed in the U.S.A. Product names mentioned herein may be trademarks and/or registered trademarks of their respective companies. Efficient Networks, Inc. shall not be liable for technical or editorial errors or omissions in this document; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material. Efficient Networks, Inc.
SpeedStream 5200 Series Bridge Limitations The limited warranty does not apply to any damage or failure caused by misuse, abuse, acts of nature, accidents (for example dropping or spilling fluids on the Hardware), or the like.
SpeedStream 5200 Series Bridge Installation Requirements Your package should contain the items listed below. If you determine anything to be damaged or missing, please contact the dealer from whom the equipment was purchased.
SpeedStream 5200 Series Bridge Connect Your SpeedStream 5200 Series Bridge 1 Place your bridge in a location where it will be well ventilated. Do not stack it with other devices or place it on carpet. 2 Connect the bridge to your PC, using the red cable between the bridge’s Ethernet port and the Ethernet port on your PC. 3 Connect the bridge to your DSL wall jack, using the purple label cable between the bridge’s DSL port and the DSL wall jack.
SpeedStream 5200 Series Bridge Configure Your Workstation Each workstation requires a unique IP address. This IP address must be supplied by your Network Service Provider. To assign an IP address to a MS Windows™ workstation that has been connected to your bridge: 1 Select Start > Settings > Control Panel > and click on Network 2 Select the Configuration tab at the top of the dialog. Users of Windows NT select the Protocols tab. 3 From the list of network components, select TCP/IP.
SpeedStream 5200 Series Bridge Verification and Troubleshooting Verify Your DSL Connection To verify that your DSL connection has been established, use any network application (such as your web browser) to access material on a remote network or the Internet. Nothing happens when I enter an address into my browser. How can I find and correct what is wrong? 1 Verify that the bridge’s power is switched ON. 2 Check the LINK light on the PC network interface card.
SpeedStream 5200 Series Bridge Your bridge is ready when the first three lights glow green. Table 1: 5300 Front Panel Lights 8 Normal Light Sequence Time If the sequence is interrupted: PWR green TEST amber LINK off 5 sec Contact Technical Support All lights flash 1 sec 1. Check cable connections and PC Ethernet card light 2. Contact Technical Support PWR green TEST green LINK off 5 sec 1. 2. PWR green TEST green LINK amber 5-10 sec 1.
SpeedStream 5200 Series Bridge Product Specifications and Support Bridging • Transparent bridging Frame Relay • Bridging (RFC 1490) Protocol Interoperability Testing • Bay Networks™, Cabletron™, Cisco™, RedBack™ (RFC 1483) WAN Interface • One Digital Subscriber Line (DSL) interface (RJ-45) LAN Interface • Built-in Ethernet connector (RJ-45) • LAN speed of up to 10 Mbps IDSL Modem specifications • Data rates ranging from 144 Kbps • 2B1Q modulation Processor • Motorola® MPC850 operating at 32 MHz • 1 MB Flas
SpeedStream 5200 Series Bridge SpeedStream 5200 Series Bridge Back Panel The back panel contains all DSL, Ethernet, console, and power interfaces. CONSOLE Table 2: 5200 Back Panel Interfaces From left to right: Power The bridge uses a standard AC power cord and has an ON/OFF switch DSL Port DSL connectivity is through this 8-pin, RJ-45 port. Ethernet Ports One Ethernet 10Base-T port (8 pin, RJ-45) Console Port Asynchronous RS232 connectivity is through this 8 pin, RJ-45 port (support only).
SpeedStream 5200 Series Bridge Port Specifications RJ-45 Port Pin Orientation Table 3: Port descriptions Pin DSL Port Ethernet Port Console Port 1 Not connected Twisted pair receive + Receive data 2 Not connected Twisted pair receive- Request to send 3 Not connected Twisted pair transmit + Not connected 4 Tip or Line A Not connected Transmit data 5 Ring or Line B Not connected Ground 6 Not connected Twisted pair transmit - Clear to send 7 Not connected Not connected Not conn
SpeedStream 5200 Series Bridge Technical Compliances and Support FCC Part 15 Class B Statement Section 15.105(b) of the Code of Federal Regulations: This equipment has been tested and found to comply with the limits for a Class B digital device, persuant of Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
SpeedStream 5200 Series Bridge Modem Technical Support If you need to contact your Network Service Provider or Efficient Networks for technical support, please have the following information ready: • SpeedStream 5200 Series Bridge model number (on the bottom of the modem) • Date of purchase • PC Operating System (e.g. Windows 9x, NT, MacOS 8.x, Unix) • Detailed description of the problem Efficent Networks Technical Support in the U.S.: Efficient Networks, Inc.
