Product Manual A
26
27
The Hydraulic Accessory Package is a factory installed option that
is ready to power any Edwards branded hydraulic accessory tools.
The Hydraulic Accessory Package includes hydraulic input and
output quick connect/disconnect hardware and a series of female
M12 and Mil Spec connections allowing for the control of your hy-
draulic accessory tool, limit switch and auto-cut tooling. To install
your accessory tool please observe the following steps.
Setup
Turn off power to machine by depressing the red stop / off button
or lockout upstream power at the main electrical panel.
Install an Edwards Hydraulic Accessory Tool:
1. Locate the operations control box adjacent to the starter box on the
feed side of the machine.
2. Locate the hydraulic quick connections and accessory controls
adjacent to drop-off side or end cap of the machine.
3. LOCATE EDWARDS HYDRAULIC ACCESSORY TOOL
IMMEDIATELY ADJACENT TO IRONWORKER.
4. With the Ironworker power off, install the male and female acces-
sory hydraulic hoses to the ironworker male and female quick con-
nect hydraulic ttings. Both ttings have a detent ball setting that
must be aligned to couple and uncouple hoses.
5. Attach the accessory tool male M12 power cable, to the M12
female limit switch port.
6. Remove the safety cap at the Push Button Port. Attach the acces-
sory tool control OUT / IN, male Mil Spec control cable to the Mil
Spec female accessory control port.
7. Turn machine ON and turn the power selection at the operations
control box to Accessory. The power selection switches power and
control from the Ironworker to the accessory tool.
8. REFER TO THE SAFETY, INSTALLATION, OPERATIONS AND
MAINTENANCE MANUALS OF YOUR EDWARDS HYDRAULIC
ACCESSORY TOOL PRIOR TO OPERATION.
9. When Disconnecting your Hydraulic Accessory, Simply reverse
procedure. Replace the Safety Cap at the push button port to
restore power to your Ironworker.
Optional Tooling - Hydraulic Accessory PackageAccessory Light
Your Edwards Ironworker may have been shipped with onboard lighting.
Accessory lighting is available as optional tooling. Designed with M12
connections, this super bright LED light plugs in to 2014 and newer
Edwards Ironworkers and has a 100,000 hour rating. Super durable
lexan lens and magnetic base allow you to attach the light on any
Ironworker surface.
Accessory work lights contain magnets -
Magnet Safety Warning!
Disclaimer: Edwards Manufacturing neither assumes nor accepts any
liability for damages resulting from the handling or use of magnets.
With your purchase, the buyer conrms that you have read and
understood the following warnings, the buyer agrees that he/she is re-
sponsible for all damages and injuries caused by magnets, which may
include personal injuries, property and magnet damages. The buyer
agrees with these terms at time of purchase.
Neodymium magnets are very strong. Handling them with care is
necessary to prevent personal injuries, property damages and magnet
damages.
1. Neodymium magnets are brittle; they can be broken or can
splinter in a collision. One should wear gloves and protective glasses
when handling these magnets, because splinters could disengage and
y from the magnets.
2. Normal Neodymium magnets will lose their magnetic proper-
ties if heated above 175°F (80° C).
3. The strong magnetic elds of neodymium magnets can
damage items such as television, computer monitors, credit cards,
bank cards, computers, diskettes and other data carriers, video tapes,
mechanical watches, hearing aids, loud speakers and VCRs. Pace-
makers may be damaged or switch to “Test Mode” in the presence of a
strong magnetic force, if a pace-maker is in use, keep a minimum of 3
feet distance.
4. Children should not be allowed to handle neodymium mag-
nets as they can be dangerous. Small magnets pose a choking hazard
and should never be swallowed or inserted into any part of the body.
5. Under no circumstances should you try to cut, saw or drill
the Neodymium magnets! The resulting dust from the magnet is very
ammable.