EDS - TECHNICAL INSTRUCTIONS END TO END (BARRIER) OPTICAL BEAM LINEAR SMOKE DETECTOR RK100B - RK200B RK100BS - RK200BS TECHNICAL MANUAL TECHNICAL INSTRUCTIONS FOR INSTALLATION, SETUP AND MAINTENANCE 1
EDS - TECHNICAL INSTRUCTIONS NOTE - the versions RK100BS-RK200BS are not equipped with the detection circuit of Turbulence. Therefore there are no items related to this circuit. In the reading and in the use of technical instructions, keep in mind this indication. QUICK INSTALLATION CHAPTER INDEX 1 - Qualified Personell 2 -Normative references 3 - Installation The procedure below is intended for trained personell with previous experience in installing EDS Beam Smoke Detectors RK100B and RK200B.
EDS - TECHNICAL INSTRUCTIONS BARRIER OPTICAL BEAM LINEAR SMOKE DETECTOR RK100B - RK200B GENERAL Note : the following instructions are suitable for the RK100B and RK200B models. The RK100/200B is a new conception of optical beam smoke detector barrier.
EDS - TECHNICAL INSTRUCTIONS 5.2 - Jumper Settings 7 - OPTICAL ALIGNMENT JP1- to enter/exit the optical alignment procedure. To activate the procedure of optical alignment JP1 must be in 2-3 (ON) position. To deactivate the procedure of optical alignment JP1 must be in 1-2 (OFF) position. • JP1 position 2-3 (ON).......alignment procedure on • JP1 posizione1-2 (OFF)...
EDS - TECHNICAL INSTRUCTIONS SIG terminal and the negative power supply one and read the analog output signal. Instead of the multimeter it is possible to use the STS01 meter (optional - fig. 11). If the output signal is very low it means that the operations of optical alignment described in chapter 5 have not been performed in the right way and therefore must be repeated 8.
EDS - TECHNICAL INSTRUCTIONS changes and, when these changes reach the programmed width and time lenght, an alarm signal is generated. The advantage of this circuit is the quicker fire detection, because the fire is detected in its beginning phase.A typical example is the complete protection of the dome of a church with important pictures on its surface. The linear optical beam smoke detectors must be installed at the baseline of the dome and therefore much lower than the ceiling.
EDS - TECHNICAL INSTRUCTIONS TECHNICAL DATA 15 - FRONTAL LEDS OPERATION 15.1 - the frontal leds of the RX during the normal operation of the detector, give out the following indications (see fig.9): • • • • normal operation: the blue led flashes every 10 seconds • • alarm: the red led is constantly ON • limit of compensation, interrupted beam, fault: the blue Led • flashes every second • 16 - MAINTENANCE 16.1 - the instrument requires an easy and periodic maintenance.
EDS - TECHNICAL INSTRUCTIONS TX RX fig.1 A A A A fig.2 lampada LAL 02 rivelatore fig.
EDS - TECHNICAL INSTRUCTIONS disco bianco white disc foro hole diodo fotoemittente photoemitting diode fig.4 fig.5 fig.
EDS - TECHNICAL INSTRUCTIONS DISTANCE SELECTION SW3 [TX] DETECTOR TYPE POSITION SW3 DISTANCE [m] 1 25-50 2 50-70 3 70-90 4 90-120 1 40-80 2 80-120 3 100-160 4 140-200 RK100B fig.7 RK200B RELATION VOLT - FLASHING VOLT N° Flash Blue Le d N° Flash Re d Le d < 0,5 OFF OFF 0,5-1 OFF 1 1-1,5 1 OFF 1,5-2 1 1 2-2,5 2 OFF 2,5-3 2 1 3-3,5 3 OFF 3,5-4 3 1 4-4,7 Variable -/+ OFF 4,7-4,95 Fix light OFF > 4,95 saturation Fix light Fix light fig.
EDS - TECHNICAL INSTRUCTIONS DS1651 LED di allineamento LED di Allarme V1 V2 P1 3 2 1 CN4 RX 9 Fehlerrelais V3 JP6 TURBO 1 2 3 SW1 JP7 1 ON 3 2 JP1 1 OFF ALI 2 3 4 SW2 3 2 1 JP4 Turborelais turbo relay 3 2 1 JP3 Alarmrelais alarm relay 3 2 1 JP2 SENS 4 fault relay ON 3 2 JP5 1 OFF MEM 8 7 6 5 4 3 2 1 fig.9 RECEIVER INTERNAL ELEMENTS P1 - trimmer for the regulation of the signal level.
EDS - TECHNICAL INSTRUCTIONS DS1653 LED V1 V2 TX fig.10 V3 JP6 POWER 1 2 3 4 2 1 SW3 TRANSMITTER INTIDE PARTS SW3 - selector for the regulation of the transmitter power (TX) - power increases from 1 to 4. Maximum power in the position 4 and mimimum in position 1.
EDS - TECHNICAL INSTRUCTIONS V- TERMINAL BLOCK OF THE TRANSMITTER V+ fig.12 SIG N3 C3 N2 TERMINAL BLOCK OF THE RECEIVER fig.
EDS - TECHNICAL INSTRUCTIONS CENTRALE DI CONTROLLO alimentazione + segnale analogico 0-5V contatto relè GUASTO SIG N3 C3 contatto relè TURBOLENZA N2 C2 contatto relè d'ALLARME N1 C1 9 - + schermo 8 7 resistenza di Allarme 6 5 4 3 2 alimentazione 11-30 Vcc connessione zona1 resistenza di fine linea V1 V+ fig.14 Example of connection of RK100/200B receiver with a zones control unit. In this case the detector is a zone of the system.
EDS - TECHNICAL INSTRUCTIONS EDS WARRANTY GENERAL CONDITIONS 1. OBJECT EDS S.r.l. - Via Cà Nova Zampieri 6, 37057 S. G. Lupatoto - Verona, Italy (hereinafter “EDS”), guarantees its products to be free from defects in materials or workmanship within the terms and conditions of this Warranty. A product found by EDS to be defective will be repaired or replaced, at the option of EDS, within 24 month after receipt of the product by EDS or an authorized EDS Service Center.
