EDL Displays, Inc. Installation and Operation Manual Model 3023 LCD Video Monitor Revised February 20, 2006 www.edldisplays.
Table of Contents INTRODUCTION 3 FEATURES 3 SPECIFICATIONS 3 INSTALLATION 5 GENERAL 5 UNPACKING 5 MECHANICAL INSTALLATION 5 SIGNAL INPUT CONNECTIONS 6 GRAPHICAL USER INTERFACE AND ON-SCREEN DISPLAY 11 Main Menu 12 PICTURE Submenu 12 OSD Submenu 13 UTILITY Submenu 13 Quick Menu 13 RECOMMENDED USE 15 Safety Precautions and Maintenance 15 Table of Figures FIGURE 1 MODEL 3023 OUTLINE DRAWING FIGURE 2 REAR PANEL INPUT CONNECTIONS FIGURE 3 IR REMOTE 9 10 11 3023 Operation and Mai
Introduction Features • 23.
(typical, at 25°C) Electromagnetic Environment Susceptibility Per EN55022 Emissions Per EN55022, FCC class A Safety Design Per UL/C 1950, EN60950 Physical Environment Temperature (operating) 0°C to +50°C Temperature (storage) -20°C to +60°C 90%, condensing Relative Humidity (operating) (to 50°C) 90%, condensing Relative Humidity (storage) (to 60°C) Sea level to 15,000ft Altitude (operating) (4500m) Sea level to 40,000ft Altitude (storage) (12000m) Shock (operating) 30g, 11msec ½ sine Shock (storage) 30g, 11
INSTALLATION GENERAL This section describes the installation of the monitor. The monitor is pre-aligned at the factory to user input requirements. However, there may still be the need for some minor adjustments to be made. Those procedures will be provided later in the Calibration Procedures section. UNPACKING Before unpacking, the carton should be inspected for shipping damage. The carton should be carefully opened and the monitor removed.
SIGNAL INPUT CONNECTIONS The Model 3023 LCD Monitor accepts both digital and analog video signals at its integrated connector (DVI-I). When connecting the monitor to a digital signal source, it is necessary to use a cable that terminates on the monitor end with a DVI-I connector that mates to the monitor’s connector, and on the source end with a DVI connector appropriate to the source – usually a DVI-D connector. (See cable descriptions below for details.
Cable Options DVI-I to DVI-D This cable should be used when connecting the monitor to a signal source that provides digital outputs by way of a DVI-D connector.
Source (output) BNC R BNC G BNC B BNC H/C (BNC RGB shells) (BNC H/C shell) Signal Analog Red Analog Green Analog Blue Composite Sync Analog RGB Ground Sync Ground DVI-I (input) C1 C2 C3 C4 C5 15 DVI-I to 5 BNC This cable should be used when connecting the monitor to an analog source that provides RGB video and separate horizontal and vertical sync by way of 5 BNC connectors.
Figure 1 Model 3023 Outline Drawing 3023 Operation and Maintenance Manual 9 EDL Displays, Inc.
VIDEO IN FUSE POWER SERIAL 1 NTSC S-VHS SERIAL 2 Figure 2 Rear Panel input connections 3023 Operation and Maintenance Manual 10 EDL Displays, Inc.
Operation Graphical User Interface and On-Screen Display The 3023 has an integrated On-Screen Display (OSD) that is used to control various display and system parameters. The OSD can be controlled by either the front keypad or an infrared (IR) remote controller. Figure 3 IR Remote 3023 Operation and Maintenance Manual 11 EDL Displays, Inc.
Keys: AUTO Press to perform an automatic adjustment procedure. Only applicable for analog RGB source modes. SOURCE 1st button press displays the current source. 2nd button press searches for the next available input source in the following order: 1. Digital RGB 2. Analog RGB 3. Composite Video 4. S-Video After S-Video the cycle starts over at Digital RGB. Note: When either the Main Menu or Quick Menu is activated, the SOURCE button acts like the EXIT button to exit the menu or to move up a level.
• • • • • • • BRIGHTNESS CONTRAST PHASE FREQUENCY H POSITION V POSITION SHARPNESS When the selects source is either of Composite or S-Video, the PICTURE functions are: • BRIGHTNESS • CONTRAST • HUE • SATURATION • SHARPNESS Use the UP or DOWN button to select the desired function. Use the LEFT or RIGHT button to set the value of the selected function.
• SCALING MODE The UP or DOWN button will scroll through the Quick Menu to select a function. Use the LEFT or RIGHT buttons to adjust or change the value of the selected function. EXIT or SOURCE will exit the Quick Menu. 3023 Operation and Maintenance Manual 14 EDL Displays, Inc.
Recommended Use Safety Precautions and Maintenance • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Do not spill any liquids into the cabinet or use your monitor near water.
• • • • • • • • • • • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. Position your monitor no closer than 16 inches and no further away than 228 inches from your eyes. The optimal distance is 24 inches for 3023. Rest your eyes periodically by focusing on an object at least 20 feat away. Blink often.
personnel. CAUTION To reduce the risk of electric shock, make sure power cord is unplugged from wall socket. To fully disengage the power to the unit, please disconnect the power cord from the AC outlet. Do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel. 3023 Operation and Maintenance Manual 17 EDL Displays, Inc.
