Setup guide

ManualsBrandsEdimax Manualscomputer componentsEW-7722UnD

Raritan PX Quick Setup Guide 1

QSG-DPX2-0M-v3.1-E  255-80-6099-00 RoHS

Raritan PX

Quick Setup Guide

Thank you for purchasing the Raritan PX intelligent power distribution unit (PDU). The intended use of the Raritan PX is distribution of

power to information technology equipment such as computers and communication equipment where such equipment is typically

mounted in an equipment rack located in an information technology equipment room.

This Quick Setup Guide explains how to install and configure the PX. For details on using the PX, access online help from the

application, or from the Support page (http://www.raritan.com/support/) on Raritan's website. For more detailed information on this

releas

e, see the latest release notes on the Support page.

Safety Precautions

WARNING! Read and understand all sections in this guide

before installing or operating this product. Failure to heed any

of the following WARNINGS may result in electric shock, fire,

personal injury and death. Prior to operating this product, the

user should read the online help and specifically the warnings

in the online help.

WARNING! Connect this product to an AC power source

whose voltage is within the range specified on the product's

nameplate.

WARNING! Connect this product to an AC power source that

is current limited by a suitably rated fuse or circuit breaker in

accordance with national and local electrical codes.

WARNING! Use this product in a dry location.

WARNING! Connect this product to a protective earth ground.

Never use a "ground lift adaptor" between the product's plug

and the wall receptacle.

WARNING! If this product is a model that requires assembly

of its line cord or plug, all such assembly must be performed

by a licensed electrician and the line cord or plugs used must

be suitably rated based on the product's nameplate ratings

and national and local electrical codes.

QS Rule

Unpacking the PX

The PX comes in Zero U, 1U, and 2U sizes. The following

describes the equipment shipped with each size. Unpack the

components. If any pieces are missing or damaged, report

this to Raritan Technical Support at tech@raritan.com, or

contact the Raritan partner where you purchased the product.

Zero U Size

 The PX device

 Mounting screws, brackets and/or buttons

 A null-modem cable with DB9 connectors on both ends

(Raritan number: 254-01-0006-00) (optional)

 Cable retention clips for the inlet and/or outlets (for some

models only)

1U and 2U Size

 The PX device

 1U or 2U bracket pack and screws

 A null-modem cable with DB9 connectors on both ends

(Raritan number: 254-01-0006-00) (optional)

 Cable retention clips for the inlet (for some models only)

Rule

Before You Begin

1. Prepare the installation site. Make sure the installation

area is clean and not exposed to extreme temperatures or

humidity. Allow sufficient space around the device for

cabling and outlet connections. Safety instructions are

provided in the PX Online Help.

2. Fill out the Equipment Setup Worksheet found in the PX

Online Help. Record the model, serial number, and use of

each IT device connected to the PDU's power outlets.

QS Rule

Mounting the PX

Use one of the mounting methods to install your PX device as

appropriate.

Summary of content (9 pages)

PAGE 1
Raritan PX Quick Setup Guide Thank you for purchasing the Raritan PX intelligent power distribution unit (PDU). The intended use of the Raritan PX is distribution of power to information technology equipment such as computers and communication equipment where such equipment is typically mounted in an equipment rack located in an information technology equipment room. This Quick Setup Guide explains how to install and configure the PX.
PAGE 2
Circuit Breaker Orientation Limitation 3. Secure with the provided end cap screws. Usually a PDU can be mounted in any orientation. However, when mounting a PDU with circuit breakers, you must obey these rules:   Circuit breakers CANNOT face down. For example, do not horizontally mount a Zero U PDU with circuit breakers on the ceiling. If a rack is subject to shock in environments such as boats or airplanes, the PDU CANNOT be mounted upside down.
PAGE 3
 mounting holes in the rack. The recommended torque for the button is 1.96 N·m (20 kgf·cm). Screw each mounting button to each baseplate. The recommended torque for the button is 1.96 N·m (20 kgf·cm). QS Rule 4. Fasten the PX device to the rack or cabinet using the baseplaed-based tools.  Use rack screws to fasten L-brackets or claw-foot brackets on the PDU to the rack.
PAGE 4
Connecting the PX to a Power Source Initial Network Configuration The distance between a PDU and its power source must be SHORTER than the PDU's line cord to avoid stretching out the cord. A locking connector used at the power source is highly recommended for a secure connection. Depending on your networking environment, the best method to initially configure your PX differs. To connect a PDU to the power source: 1. Verify that all circuit breakers on the PX device are set to ON. If not, turn them ON.
PAGE 5
PX3 Phase I Models A PX3 phase I model's front panel display is similar to the following diagram.  Password: raritan 4. Change the default password when prompted. 5. To change network settings, choose Device Settings > Network. See online help for detailed information. QS Rule Using the CLI Initial configuration via CLI involves these two steps. Step 1: Connect the PX to a Computer (on page 5) Step 2: Configure the PX (on page 5) To retrieve the IP address: 1.
PAGE 6
b. Password: raritan (or a new password if you have changed it). 5. If prompted to change the default password, follow onscreen instructions to type your new password. 6. The # prompt appears. 7. Type config and press Enter. 8. To configure network settings, type appropriate commands and press Enter. All commands are case sensitive. a.
PAGE 7
Whether to Use this command Tip: To override the DHCP-assigned DNS servers with those you specify manually, type this command: Make the connection successful by ignoring the "incorrect" system time network wireless allowConnectionWithIncorrectClock network overrideDNS
PAGE 8
Command Description show network wireless details Show all wireless parameters. Connecting the Wireless LAN Adapter You can connect the wireless LAN adapter either to the PX or to a USB docking station attached to the PX. Tip: You can type "show network wireless" to display a shortened version of wireless settings. To make a wireless connection: Do one of the following: 11. If all are correct, type exit to log out of the PX. If any are incorrect, repeat Steps 7 to 10 to change network settings.
PAGE 9
Automatic driver installation in Windows®: For detailed information on how to remove it, see the topic titled "Replaceable Controller" in the PX3 online help. 1. Make sure the PX is NOT connected to the computer via a USB cable. 2. Run dominion-serial-setup-.exe on the computer and follow online instructions to install the driver. Note: If any Windows security warning appears, accept it to continue the installation. 3. Connect the PX to the computer via a USB cable.