Multi-Language QIG in Driver CD ================================================== Český: Českého průvodce rychlou instalací naleznete na přiloženém CD s ovladači Deutsch: Finden Sie bitte das deutsche QIG beiliegend in der Treiber CD Español: Incluido en el CD el QIG en Español Français: Veuillez trouver l’français QIG ci-joint dans le CD Italiano: Incluso nel CD il QIG in Italiano Magyar: A magyar telepítési útmutató megtalálható a mellékelt C D -n Nederlands: De nederlandse QIG treft u aan op de bijges
Copyright© by Edimax Technology Co, LTD. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company.
Contents 1. Introduction ............................................................................ 4 2. Package List........................................................................... 5 3. Hardware Guide ..................................................................... 5 4. System Requirements............................................................ 5 5. Hardware Installation ............................................................. 6 6. Driver Installation ............................
1. Introduction English PCI Express is the next generation of I/O interconnection standards to support the high bandwidth required by PCs, consumer electronics and communication devices. The architecture is a cost-effective, low-pin count, and point-to-point technology to maximize the bandwidth, reduce the costs and design complexity and enable smaller form factors. This card is the best solution for Gigabit Ethernet PCI Express with potential transfer rates of 2.
2. Package List Please check if the following items are included and in good condition upon opening your package. Contact your vendor if any item is damaged or missing. 1. One Gigabit Ethernet PCI Express Adapter 2. One Quick Installation Guide 3. One CD-ROM (Including drivers and Multi-language Quick Installation Guide) 3. Hardware Guide 1. Gigabit Link GREEN LED 2. 10/100 bit Link RED LED 3. LINK LED 4. Active LED 4.
5. Hardware Installation Follow the instruction below to install the Gigabit Ethernet PCI Express Card: 1. Turn your computer off and remove the power plug from the power socket. 2. Open the cover of the computer case. 3. Remove the metal bracket on the rear of a free PCI Express slot. 4. Insert the card into one free PCI Express slot and screw it firmly on the bracket side. 5. Place the cover back onto the computer. 6. Insert the plug into the power socket, and turn on PC.
6. Driver Installation 1. Windows 2000/XP/2003 Driver Installation Once the Windows 2000, XP and 2003 startup, the system will detect the Gigabit Ethernet PCI Express Adapter. Follow the procedures to install Gigabit Ethernet PCI Express Adapter driver under Microsoft Windows XP server pack 2 Operation System 1. Please click "Cancel" to close it, when Found New Hardware Wizard Windows pop-up. 2. Insert the CD shipped along with the Gigabit PCI Express Adapter into your CD-ROM drive. The Autorun.
3. The following screen will be displayed. Click “Setup Utility ”. 4. The following screen will be displayed. Please select the driver based on your Windows XP/2000/2003 Operation System.
The “Gigabit PCI Express Adapter Utilities - InstallShield Wizard” is displayed auto run. 5.
6. Please select “ I accept the terms in the license agreement “ and click “ Next “ 7. Please click “ Install “ to install the Gigabit PCI Express adapter utility.
8. The system starts installing the Gigabit PCI Express adapter utility. 9. Click "Finish" to complete Gigabit Ethernet PCI Express Adapter installation.
7. Hardware Check Go to “Device Manager” which you can access from the Control Panel. You should see an "Generic Marvell Yukon Chipset based Gigabit Ethernet Controller" under "Network Adapter" item.
8. Networking Settings 1.Click "Network Connection" in Control Panel to set your network settings. 2. Right-click the Local Area Connection of Gigabit Ethernet card, then select "Properties" from menu. 3. Double-click the "Internet Protocol (TCP/IP)" item to set network settings.
4. Right-click the Local Area Connection of the Gigabit Ethernet card, then select "Status" from the menu to check the network status.
9. Vista Driver Installation Once the Windows Vista startup, the system will detect the Gigabit Ethernet PCI Express Adapter. Follow the procedures to install Gigabit Ethernet PCI Express Adapter driver under Microsoft Windows XP server pack 2 Operation System 1. Please click "Cancel" to close it, when Found New Hardware Wizard Windows pop-up. 2. Insert the CD shipped along with the Gigabit PCI Express Adapter into your CD-ROM drive. The Autorun.exe program should be executed automatically.
3. The following screen will be displayed. Click “Setup Utility ”. 4. The following screen will be displayed. Please select the driver based on your Windows Vista Operation System.
The “Gigabit PCI Express Adapter Utilities - InstallShield Wizard” is displayed auto run. 5.
6. Please select “ I accept the terms in the license agreement “ and click “ Next “ 7. Please click “ Install “ to install the Gigabit PCI Express adapter utility.
8. The system starts installing the Gigabit PCI Express adapter utility. 9. Click "Finish" to complete Gigabit Ethernet PCI Express Adapter installation.
10. Hardware Check Go to “Device Manager” which you can access from the Control Panel. You should see an "Generic Marvell Yukon Chipset based Gigabit Ethernet Controller" under "Network Adapter" item.
11. Networking Settings 1. Click "Network Sharing Center " in Control Panel to set your network settings. 2. Click "Manage network connections " ito set your network settings.
3. Double-click the "Internet Protocol (TCP/IP)" item to set network settings.
12. Troubleshooting The computer cannot detect the Gigabit Ethernet PCI Express Adapter 1. Make sure that the PCI Express cards is correctly plugged into the PCI Express slot; if not, turn off the computer and plug it in again 2. If the PCI Express card is plugged in correctly, see if the golden connectors on the card are clean; if not, clean the connector surface. 3. If it is still NOT working, please change to another PCI Express slot on your motherboard. 4.
I cannot use Gigabit Ethernet transfer speeds. 1. Please affirm your Ethernet environment supporting Gigabit structure. 2. Please use CAT6 UTP/STP cable. How to configure 10/100/1000M Ethernet structure? Connect 10/100/1000M Ethernet over unshielded twisted pair (UTP) cable. Gigabit Ethernet PCI Express card has the ability to detect the speed automatically and operate on the speed without manual reconfiguration.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
26
