AR-7288WnA / AR-7288WnB Quick Installation Guide 09-2014 / v1.
COPYRIGHT Copyright Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd. Edimax Technology Co., Ltd.
PRODUCT INTRODUCTION Package Contents Before you start using this product, please check if there is anything missing in the package and contact your dealer to claim the missing item(s): ADSL2+ router 12V Power adapter RJ-45 Ethernet cable RJ-11 telephone line Quick installation guide CD containing setup wizard, user manual & QIG Splitter 5dBi Antenna System Requirements Recommended system requirements are as follows.
ADSL Green Internet Green Red LAN1~4 Green Green WPS Green ON SLOW BLINK FAST BLINK ON BLINK OFF ON ON BLINK OFF On Blinks Off Off Blinks ADSL line is synchronized and ready to use ADSL synchronization failed ( Please refer to Note 1) ADSL negotiation is in progress.
Rear Panel Items Description Power ON/OFF 12V Power connector Wireless LAN ON/OFF (Press the button gently and let go after 1 second to enable WLAN function, and press the button gently and let go after 1 second to disable.) WPS ON/OFF (Press the button gently and let go after 1 second to WPS enable WLAN function, and press the button gently and let go after 1 second to disable.
GETTING STARTED A. Hardware Installation Step 1: Connect the ADSL line Connect the Line interface of the device to the Modem interface of a splitter using a telephone cable. Connect a telephone to the Phone interface of the splitter using a telephone cable. Connect the Line interface of the splitter to your existing, incoming line. The splitter has three interfaces: Line: Connect to a wall phone jack (RJ-11 jack). Modem: Connect to the ADSL jack of the device. Phone: Connect to a telephone set.
Step 4: Check the ADSL LED status Please check the ADSL LED on the front panel. This light indicates the status of your ADSL broadband through your telephone line. If the light is on, you can continue setup. However if the light is flashing, there is no broadband line detected. Please call your Internet Service Provider (ISP) and inform them about the flashing ADSL light to resolve the issue.
4. Select the “Local Area Connection” icon and right-click it to open the sub-menu, and then select “Properties”. 5.
6. Ensure that “Obtain an IP address automatically” and “Obtain DNS server address automatically” are selected and then press “OK”. B. Internet Connection You can configure the router by running the setup wizard on the CD-ROM included in the package contents. When you start the setup wizard, you will see the following screen. Please follow the on screen instructions until setup is complete.
Alternatively, if you lose the CD-ROM or prefer a web based setup, you can login to the ADSL router using Internet Explorer, and configure the router from there using the web-based interface. Please follow the instructions below: 1. Enter the router’s default IP address: “192.168.2.1” into your PC’s web browser and press “Enter”. 2. The login screen below will appear. Enter the default username “admin” and default password “1234” and click “OK”. 3. You will arrive at the system status page as shown below.
4. In the navigation bar across the top of the screen, click “Quick Start”. The Wizard page of the web-based interface allows fast configuration of the Internet connection and other parameters. Please refer to the user manual for detailed information on these parameters. Enter the required information on each page of the quick start and click “Apply” until the quick start is complete.
Appendix I: How to Install and Access the USB Storage 1. Plug USB storage into USB on AR-7288WnA. 2. Log in web management. (Example: HTTP://192.168.2.1) 3. Choose Advanced Setup > Storage Service Storage Device Info, and the following page appears. In this page, you can view the USB device info. 4. Choose Advanced Setup > Storage Service > User Accounts, and the following page appears. In this page, you may add or remove storage user accounts. Click the Add button to display the following page.
5. Click Start, input \\192.168.2.1 (192.168.2.1 is IP address of AR-7288WnA), and then press Enter. 6. Enter username and password which you have added at step 4, and then click OK. 7. It will display the USB device. Double click left mouse on the fold, and then you are able to access the data in the USB storage.
Appendix II The following are the general settings usually provided by the Internet Service Providers (ISP). Upon running the “setup wizard” on CD-ROM (See Quick Installation Guide page 8) OR “Quick Start” (See Quick Installation Guide page 10), all the below Settings (Pointers No. 1 & No. 2) are Pre-Set in AR-7288WnA; except Pointer No. 3, Username and Password (As provided by your ISP). Need to be Input by User accordingly.
PTC General Warning The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty.
