Multi-Language QIG on the CD Český Českého průvodce rychlou instalací naleznete na přiloženém CD s ovladači. Deutsch Auf der beiliegend Treiber CD finden Sie deutsche Anleitung zur Schnellinstallation. Español Incluido en el CD el G.R.I. en Español. Français Veuillez trouver l’français G.I.R ci-joint dans le CD. Italiano Incluso nel CD il Q.I.G. in Italiano. Magyar A magyar telepítési útmutató megtalálható a mellékelt CD-n. Nederlands De nederlandse Q.I.G.
English Copyright Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd. Edimax Technology Co., Ltd.
Thank you for purchasing the Edimax 3G-6218n 150Mbps Wireless 3G Portable Router! This 3G router is the ideal choice for anyone who is constantly on the go. With the Edimax 3G-6218n 150Mbps Wireless 3G Portable Router, all your computers and network devices can share a single, high-speed xDSL/cable or 3G/3.5G Internet connection.
LED Definitions LED Name Light Status On PWR Flashing CHG WLAN Ethernet Internet Off On Off On Flashing Off On Flashing On Flashing Off Description Router powered on Battery power low (15-20 minutes left) or battery not installed Router powered off Battery charging Battery fully charged WPS function enabled Wireless LAN activity (transferring data) Wireless network switched off Ethernet port connected Ethernet activity (transferring data) Connection established Establishing connection Connection not
Right and Left Side Panel RJ-45 Item Name LAN/WAN switch WPS/Reset button ON/OFF switch Description Switches the RJ-45 port to LAN or WAN mode. Switch to WAN mode if you want to access the Internet through your xDSL or cable modem. This cable connection can also act as a backup for your 3G connection. Initiates WPS or resets the router to factory defaults (clears all settings).
Getting Started Before you start using this 3G router, please follow the following instructions to install and charge the battery. 1. Remove the battery cover, insert the supplied battery into the slot, and then replace the battery cover.
2. Charge the battery by connecting the power adapter to the mini-USB port and then to the wall socket. It takes about 4 hours to fully charge the battery. Note : Please charge the battery for 8 hours on the first charge. Note: You can power the router via a wall socket without the battery installed; but powering the router via a computer without the battery installed might cause decreased performance. 3. The “CHG” LED will go on when the battery is charging.
4. Turn on the router by switching the “ON/OFF” switch to the “ON” position. Warning: 1. Always switch the device off before removing the battery. 2. For your safety, only use the battery and power adapter supplied with the product.
5. Connect your 3G/3.5G USB modem to the USB port on the router. 6. Connect the router to your computer via an Ethernet cable. Note: It is recommended that you configure the router through the Ethernet port for the first time. 7. Please check all the LEDs. The “PWR/CHR” LED should be on, and the “ETHERNET” LED should be on if a computer/network device is connected and correctly powered.
Method 1: Setting up the router with the CD wizard Please follow the following instructions to set up the 3G router with the CD wizard: With the setup wizard in the CD-ROM, you can easily set up a 3G/3.5G connection, an Ethernet connection, SSID, wireless security, or upgrade the router’s firmware. After starting the setup wizard, please choose the language of your choice. Note 1: 3G/3.5G connections and xDSL/cable connections cannot be used at the same time.
Method 2: Setting up the router with the web-based UI If you lose the CD-ROM, you can setup the router with the web-based user interface. Setting client computers to obtain IP addresses automatically: 1. Click the “Start” button (it should be located at the lower-left corner of your screen), then click “Control Panel”. Double-click the “Network and Internet Connections” icon, click “Network Connections”, then double-click “Local Area Connection”.
2. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically”, then click “OK”. 3. Please input “192.168.2.1” in the web browser’s address bar and press “Enter”. You should see the an authentication window. 4. Please input “admin” in the “User name” field and “1234” in the “Password” field. Click the “OK” button to enter the web configuration interface. For more instructions, please refer to the user manual in the supplied CD-ROM.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Estonia, Hungary, Latvia, Lithuania, Malta, Poland, Romania, Slovakia, Slovenia, the Netherlands, Portugal, Spain, Sweden, and the United Kingdom. The ETSI version of this device is also authorized for use in EFTA member states: Iceland, Liechtenstein, Norway, and Switzerland. EU Countries not intended for use None A declaration of conformity is available on www.edimax.
15
