Edimax Gemini Home Wi‐Fi Roaming Upgrade Kit RE23S Quick Installation Guide 02‐2017 / v1.
I. Product Information RE23S are Wi‐Fi roaming extenders. After setting up your roaming network, your Wi‐Fi devices (smartphones, tablets etc.) will automatically connect to the best available Wi‐Fi signal as you move around. I‐1. Package Contents ‐ ‐ ‐ ‐ ‐ ‐ RE23S x 2 CD with multi‐language QIG & user manual Quick installation guide (QIG) Access key card Antenna x 4 RJ45 cable I‐2. System Requirements ‐ Wi‐Fi extender/Wi‐Fi bridge mode: Existing 2.4GHz and/or 5GHz wireless network.
I‐3. LED Status LED Color Status Excellent location. Signal strength: 60 – 80% On 2.4GHz 5GHz LAN Slow Flashing Good location. Signal strength: 40 – 60% & 80 ‐ 100% Quick Flashing Poor location. Signal strength: Below 40% Green Orange Description Off No signal detected. On Excellent location. Signal strength: 60 – 80% Slow Flashing Good location. Signal strength: 40 – 60% & 80 ‐ 100% Quick Flashing Poor location. Signal strength: Below 40% Off No signal detected.
II. Initial Setup First you need to link one RE23S to your router by Wi‐Fi or Ethernet cable: (i) Simply plug in and use the WPS button (push for 3s on each device). The RE23S will automatically link to your router and use the same Wi‐Fi name and password as your router. That’s it – ready to add more extenders. Or (ii) Just plug in and connect the RE23S to your router with an Ethernet cable. The RE23S will automatically link to your router and use the Wi‐Fi name and password on your access card.
3. Open a web browser and enter the URL http://edimaxext.setup or scan the QR‐Code below and click Get Started.
If you cannot access http://edimaxext.setup, please make sure your computer is set to use a dynamic IP address. For more information please refer to the user manual. 4. Select Yes, I need a Wi‐Fi Extender to continue setup wirelessly, or Change to a Different Mode and then Access Point Mode if you want to link your RE23S to your router with an Ethernet cable. 5. Follow the on‐screen instructions for your selected mode to complete setup. You can configure the product for 2.
III. Adding More Extenders & WPS Adding more RE23S roaming extenders to your network is easy with the WPS button. Additional extenders automatically follow the Wi‐Fi settings of the first RE23S linked to your router. WPS can also be used to link the first RE23S to your router for first‐time setup. 1. Press the WPS button on your linked extender (or router for first‐time setup) for 3 seconds. 2. Within two minutes, press and hold the WPS button for 3 seconds on the new extender. 3.
IV. Reset If you experience problems with your extender or if you want to change the extender to a different operating mode, you can reset the device back to its factory settings. This resets all settings back to default. 1.Press and hold the reset button for at least 10 seconds and release when the green LED is flashing. 2.Wait for the extender to restart. After a period of time the extender is ready for setup when the green LED is flashing again.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
EU Countries Not Intended for Use None 9
EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 2006/95/EC, 2011/65/EC. Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive 2006/95/CE, 2011/65/CE. Čeština: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic 2006/95/ES, 2011/65/ES.
Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European R&TTE directives. Equipment: Model No.: AC2600 Wi‐Fi Roaming Mesh Extender RE23S The following European standards for essential requirements have been followed: Spectrum: ETSI EN 300 328 V1.9.1 ETSI EN 301 893 V1.8.1 EMC: EN 301 489‐1 V1.9.2 (2011‐09); EN 301 489‐17 V2.2.
Notice According to GNU General Public License Version 2 This product includes software that is subject to the GNU General Public License version 2. The program is free software and distributed without any warranty of the author. We offer, valid for at least three years, to give you, for a charge no more than the costs of physically performing source distribution, a complete machine‐readable copy of the corresponding source code.
intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License. 7.
