SAFETY PRECAUTIONS Read all of the instructions before using this appliance. When using this appliance, always exercise basic safely precautions, including the following: • • • • • • • • • • • • • • • • • • • • • • This appliance is designed for household use only and not for commercial use. Do not use the appliance for uses other than that for which it is designed. Do not use the appliance if the power supply cord is damaged.
INTRODUCTION Thank you for purchasing this EdgeStar product. We are glad you choose us and we take pride in knowing that like our products our customer service will be just as dependable. Once you complete our easy unit set up by following the manual, it will provide you years of great service. We ask all of our customers to please save the original product packaging in case you need to safely transport the unit. For Your Records: Please write down the model and serial number below for future reference.
TABLE OF CONTENTS ________________________________________________________________________ UNPACKING ACCESSORIES AND INVENTORY.................. 4 Additional Accessories...................................... 4 SETTING UP YOUR REFRIGERATOR......................... 4-6 Proper Location........................................... 4 Installing the Casters....................................... 5 Grounding Instructions...................................... 5 Understanding the Temperature Control Setting...........
UNPACKING ACCESSORIES AND INVENTORY If you purchased your EdgeStar Refrigerator as a Draft Beer Dispenser, it is supplied with all the accessories you need to install and tap a standard American Sankey Tap ½ barrel keg. This unit can also fit ¼ barrel, 1/6 barrel, and Cornelius kegs with standard American Sankey Tap connections. All you need to do is set up the Draft Beer Dispenser, supply the full keg of beer, and fill the CO 2 tank.
SETTING UP YOUR FRIDGE & BEER DISPENSER Installing the Casters 1. With the contents inside the cabinet removed set the beer dispenser on its side. 2. Insert each caster into the holes on the bottom corners of the cabinet. Screw the casters in hand tight. 3. With all four casters tightened evenly, stand the unit in an upright position. Note: Allow the refrigerator to stand in an upright position for 8 hours before turning on the power. This will ensure that the coolant has settled.
Understanding Normal Operating Sounds • Sizzling or popping sounds occur during the automatic defrost cycle. • Bubbling or gurgling sounds and slight vibrations are the result of the refrigerant circulating through the cooling coils. • Cracking or popping sounds are caused by the expanding and / or contracting of the cooling coils during the automatic defrost cycle. • Dripping sounds occur as ice melts from the evaporator and flows into the water collection tray during the automatic defrost cycle.
Connecting the CO2 Cylinder to the CO2 Regulator and Installing the CO2 Cylinder Holder Warning CO2 can be dangerous! CO2 cylinders contain high-pressured gas, which can be hazardous if handled improperly. Please handle with care. Note This section describes general CO2 and keg installation. For specific instructions, see the instructions included in the accessory box. 1. To install the CO 2 gas line tube to the regulator, attach one end of the CO 2 tube, to the hose barb connection on the CO 2 regulator.
Installing the Keg Coupler– Tapping the Beer Your beer dispenser comes with American Sankey Tap. Before purchasing a keg, check with your beer distributor to make sure that supplied American Sankey Tap can be used. Many European beers require a different tap. Please contact EdgeStar customer service online via email at service@edgestar.com or by telephone at 1-866-319-5473 for more information. 1.
Setting the Correct Pressure for the CO2 Regulator When dispensing keg draft beer, the goal is to keep the CO 2 level prescribed by the brewer. Any change in the CO 2 level will alter the taste, pouring characteristics and appearance of the beer. Most breweries in the U.S. recommend a CO 2 pressure between 12-14 lbs for Ale and Lager types of draft beers. This CO 2 pressure will maintain the level of carbonation specified by the brewery.
Setting the Regulator EdgeStar’s Draft Beer Dispenser comes with a single gauge CO 2 gas regulator that has a 0-60 lb. pressure gauge showing the gas output pressure. Once the regulator is securely attached to the gas cylinder: 1. Close the shut-off valve on the regulator, and open the valve on the cylinder completely. 2. Slowly turn the regulator adjustment screw until the desired pressure is shown on the output gauge.
Dispensing the Beer and Proper Drawing Technique Note: Allow the keg to settle and acclimate to refrigeration for 2-4 hours prior to dispensing beer. Using the proper draw technique to dispense beer should allow you to fill a 12 oz glass leaving approximately ¾”-1” of foam. 1. Make sure that the beer dispenser is plugged in properly to a 120V, 60Hz, 15Amp grounded outlet. 2. Rinse a “Beer Clean” glass under cold water. (see below for more information on “Beer Clean”) 3.
Understanding Beer Temperature • Select and maintain the proper temperature inside the refrigerator cabinet. This is necessary to maintain the flavor freshness of the beer. Adding additional unrefrigerated products, such as meats, vegetables, fish, etc. while attempting to chill beer will cause a fluctuation in the temperature, resulting in cloudy beer. • The recommended temperature for storing and serving chilled beer is between the high 30s and mid 40s.
Beer Serving Guide What a half barrel (full keg) of beer provides you: No. Glasses 192 236 264 290 353 4 Glass Size 12 oz. 10 oz. 9 oz. Half Barrel (full size) Keg = 15.5 Gallons 8 oz. = 1984 Fluid Ounces 7 oz. Half Barrel (full size) Keg = 6.75 Cases of 12 ounce Bottles 6 oz. CONVERTING THE BEER DISPENSER TO A REFRIGERATOR You may convert your beer dispenser to a compact refrigerator by following instructions below: 1. Make sure the CO 2 tank is closed. Safely disconnect the CO 2 , keg, and all lines.
TROUBLESHOOTING YOUR REFRIGERATOR The refrigerator is not working - Check that the plug is inserted correctly into the wall socket - Check that there is power to the wall socket by plugging in another appliance. - Check that the thermostat control is not “Off” Food in the refrigerator compartment is freezing - Make sure that food is not touching the back wall of the refrigerator - Turn the thermostat to a warmer setting.
Glassware is not “Beer Clean” Elongated dispensing hose. No beer flow from dispenser Low/Empty CO 2 cylinder. Closed CO 2 valve and/or shutoff valve. Empty beer keg. Line or dispenser obstructions. Improper connections(s) Sputtering Draw Dispense system requires cleaning. Keg Coupler installed incorrectly Line or dispenser obstructions. Improper draw technique Faucet Dripping Handle not fully returned to close position.
LIMITED WARANTY This EdgeStar product is warranted to be free from defective workmanship and materials for the first year following the date of original purchase. Replacement parts will be supplied free of charge for the first year following the date of original purchase. Labor will be performed free of charge for the first 90 days following the date of original purchase.
For information on EdgeStar and to view our full line of products, please visit our website: http://www.edgestar.
