TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS…………………………………………………1 PREPARING YOUR ICE MAKER FOR USE IMPORTANT SAFETY TIPS.……………………………………………………………….2 GETTING TO KNOW YOUR UNIT… ………………………………………………………..3 OPERATING PROCEDURES & MAINTENANCE UNPACKING YOUR ICE MAKER ..………….…………………………………………...4 CONNECTING YOUR ICE MAKER……………….……….……………………………..4 CLEANING AND MAINTAINING YOUR ICE MAKER….……………………………….4 USING YOUR ICE MAKER……………….……..………………………………………...5 TROUBLESHOOTING...……………………….
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol: ! All safety messages will follow the safety alert symbol and the word “DANGER” or “WARNING”. ! DANGER ! WARNING These words mean: You can be killed or seriously injured if you don’t immediately follow instructions.
PREPARING YOUR ICE MAKER FOR USE IMPORTANT SAFETY TIPS When using electrical appliances, basic safety precautions should be followed to reduce the risk of fire, electric shock, and/or injury to persons or property. Read all instructions before using any appliance. z Do not operate this or any other appliance with a damaged cord. Connect to properly polarized outlets only. No other appliance should be plugged into the same outlet. Be sure that the plug is fully inserted into the receptacle.
GETTING TO KNOW YOUR UNIT 1. Cover: Features a transparent window for interior visibility. 2. Control Panel: Easy to use touch display setting with function indicators. A) Starts or stops the ice-making cycle. B) Selects the ice cube size. 3. Water drain cap: For draining water from water reservoir. 4. Ice basket. 5. Ice scoop. 6. Ice shovel.
OPERATING PROCEDURES & MAINTENANCE UNPACKING YOUR ICE MAKER 1. Remove the exterior and interior packaging. Check that ice basket and ice scoop are included. If any parts are missing, please contact customer service. 2. Clean the interior with lukewarm water and a soft cloth. Take out the ice basket and clean it . 3. Find a location for your ice maker that is protected from direct sunlight and other sources of heat (i.e.: stove, furnace, radiator). Place the ice maker on a level surface.
USING YOUR ICE MAKER 1. Select the size of the ice cube by pressing the “Select” button. If the room temperature is lower than 60°F, it is best to select the small or medium ice size, otherwise the ice cubes might stick together. 2. Open the cover, remove the ice basket and pour water into tank. Keep water level below the level mark. 3. Press “Power” on the control panel to begin the ice making cycle. 4. The ice making cycle lasts 6 to 14 minutes, depending on the size of the ice cubes selected. 5.
The “Water” and “Ice” indicators are both flashing. The ice cubes stick together. The compressor makes a loud buzzing noise The unit does nothing The ice making cycle seems normal but no ice is produced. The ice shovel cannot move. Check if the ice is blocking the ice pusher, otherwise, consult service. The ice cycle is too long. Stop the ice maker, and restart it when the ice blocks melt. Select the small ice button. The water temperature in the inner tank is too low.
TECHNICAL SPECIFICATIONS & CIRCUIT DIAGRAM TECHNICAL SPECIFICATIONS Model IP200P Climate Type SN/N Protection Type I P o we r 110V~120V/60Hz Rated Current 2.1 A Input Power 252W Refrigerant R134a/120g Vesicant R141b Net Weight 45.
PARTS BREAKDOWN DIAGRAM 1. Control Panel 13. Left Board 24. Adjustable Foot 2. Display PCB 14. Filter 25. Compressor 3. Panel 15. Solenoid Valve 26. Underpan 4. Inner Liner 16. Pressure Controller 27. Control Box 5. Handle 17. Container 6. Ice Shovel Refrigerant 29. Transformer 7. Ice Case 18. Back Board 30. Right Board 8. Evaporator 19. Strengthen Plate 31. Driving Motor 9. Steel Water Supply Pipe 20. Cooling Fan 32. Ice Basket 10. Steel Shell 21. Condenser 33.
LIMITED WARRANTY This EdgeStar product is warranted to be free from defective workmanship and materials for the first year following the date of original purchase. Replacement parts will be supplied free of charge for the first year following the date of original purchase. Labor will be performed free of charge for the first 90 days following the date of original purchase.
All products and components replaced by EdgeStar under warranty service become the property of EdgeStar. OBTAINING WARRANTY SERVICE: Contact EdgeStar for troubleshooting assistance and warranty service authorization at 1-866-319-5473. Please have your order receipt available to confirm the date of purchase. Once an EdgeStar authorized representative has confirmed that your product is eligible for warranty service, the product must be returned to an EdgeStar authorized repair facility.
