USER GUIDE BARRICADETM N 802.
BarricadeTM N SMCWGBR14-N2 User Guide No. 1, Creation Road III, Hsinchu Science Park, 30077, Taiwan, R.O.C.
Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to change specifications at any time without notice. Copyright © 2011 by SMC Networks, Inc. No.
WARRANTY AND PRODUCT REGISTRATION To register SMC products and to review the detailed warranty statement, please refer to the Support Section of the SMC Website at http:// www.smc.com.
COMPLIANCES FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
COMPLIANCES IMPORTANT NOTE: FCC RADIATION EXPOSURE STATEMENT This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be colocated or operating in conjunction with any other antenna or transmitter. To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations.
ABOUT THIS GUIDE PURPOSE This guide details the hardware features of the wireless router, including its physical and performance-related characteristics, and how to install the device and use its configuration software. AUDIENCE This guide is for PC users with a working knowledge of computers. You should be familiar with Windows operating system concepts.
CONTENTS WARRANTY AND PRODUCT REGISTRATION 4 COMPLIANCES 5 ABOUT THIS GUIDE 7 CONTENTS 8 1 INTRODUCTION 11 Conventions 12 Main Features 12 Key Hardware Features 13 Package Contents 13 Front Panel 13 LED Indicators 14 Rear Panel 15 Antennas 15 Power Connector 15 Reset Button 15 USB Port 15 Ethernet WAN Port 16 Ethernet LAN Port 16 2 CONNECTING THE ROUTER 17 System Requirements 17 Installation Environment Requirements 17 Connecting the Router 18 3 QUICK INSTALLATIO
CONTENTS General Status 29 ARP List 29 Quick Setup 30 5 NETWORK SETTINGS 31 WAN 31 MAC Clone 40 LAN 41 Dynamic DNS 41 Comexe.cn DDNS 42 Dyndns.org DDNS 43 No-ip.
CONTENTS 11 ACCESS CONTROL SETTINGS 83 Rule 83 Host 86 Target 88 Schedule 90 Parental Control 92 12 ADVANCED ROUTING 96 Static Routing List 96 13 QOS SETTINGS 98 QoS Settings 98 Rules List 99 14 SYSTEM TOOLS 101 Time Setting 101 Diagnostic 102 Settings Management 104 Firmware Upgrade 104 Factory Defaults 105 Backup & Restore 105 Reboot 106 Password 107 System Log 108 Statistics 110 Local Management 111 Remote Management 112 A FAQ 114 B CONFIGURING THE PCS
1 INTRODUCTION The SMCWGBR14-N2 Wireless N Gigabit Router integrates a 4-port switch, firewall, NAT router, and wireless access point. The Wireless N Gigabit Router delivers exceptional range and speed, which can fully meet the needs of Small Office/Home Office (SOHO) networks and users demanding higher networking performance. INCREDIBLE SPEED The SMCWGBR14-N2 Wireless N Gigabit Router provides wireless connections up to 300 Mbps with other 802.11n wireless clients.
CHAPTER 1 | Introduction Conventions CONVENTIONS The “Router” or “SMCWGBR14-N2” mentioned in this guide stands for the SMCWGBR14-N2 Wireless N Gigabit Router without any explanation. MAIN FEATURES ◆ Complies with IEEE 802.11n to provide a wireless data rate of up to 300 Mbps. ◆ One 10/100/1000 Mbps Auto-Negotiation RJ-45 WAN port, four 10/ 100/1000 Mbps Auto-Negotiation RJ-45 LAN ports, supporting Auto MDI/MDIX ◆ Provides WPA/WPA2, WPA-PSK/WPA2-PSK authentication, TKIP/AES encryption security.
CHAPTER 1 | Introduction Key Hardware Features KEY HARDWARE FEATURES The following table describes the main hardware features of the wireless Router. Table 1: Key Hardware Features Feature Description WAN Port One 1000BASE-T RJ-45 port for connecting to the Internet. LAN Port Four 1000BASE-T RJ-45 ports for local network connections. USB Port One USB slot for USB mass storage device. Reset Button For resetting the unit and restoring factory defaults.
CHAPTER 1 | Introduction Front Panel LED INDICATORS The wireless Router includes ten status LED indicators, as described in the following table. Table 2: LED Behavior LED Status Description Power On The unit is receiving power and is operating normally. Off There is no power currently being supplied to the unit. On The Router is initializing. Flashing The Router is working properly. Off The Router has a system error. On/Flashing The 802.
CHAPTER 1 | Introduction Rear Panel REAR PANEL Figure 2: Rear Panel POWER RESET USB The following items are located on the rear panel (from left to right). ANTENNAS The access point includes integrated MIMO antennas for wireless communications. A MIMO antenna system uses two or more identical antennas to receive and transmit signals, helping to increase data throughput and range.
CHAPTER 1 | Introduction Rear Panel ETHERNET WAN PORT A 1000BASE-T RJ-45 port that can be attached to an Internet access device, such as a DSL or Cable modem. ETHERNET LAN PORT The wireless router has four 1000BASE-T RJ-45 ports that can be attached directly to a PC or 10BASE-T/100BASE-TX/1000BASE-T LAN segments. This port supports automatic MDI/MDI-X operation, so you can use straight-through cables for all network connections to PCs, switches, or hubs.
2 CONNECTING THE ROUTER SYSTEM REQUIREMENTS You must meet the following minimum requirements: ◆ Broadband Internet access service (DSL/Cable/Ethernet) ◆ One DSL/Cable modem that has an RJ-45 connector ◆ PCs with working Ethernet adapters and Ethernet cables with RJ-45 connectors ◆ TCP/IP protocol on each PC ◆ Web browser, such as Internet Explorer 5.5 or above, Netscape 4.7 or above, Mozilla Firefox 1.
CHAPTER 2 | Connecting the Router Connecting the Router CONNECTING THE ROUTER Before installing the Router, make sure your PC is successfully connected to the Internet through the broadband service. If there is any problem, first contact your ISP. Install the Router according to the following steps. 1. Power off your PC, Cable/DSL modem, and the Router. 2. Find a good location for the Router. The best place is usually at the center of your network.
CHAPTER 2 | Connecting the Router Connecting the Router Figure 3: Hardware Installation – 19 –
3 QUICK INSTALLATION GUIDE TCP/IP CONFIGURATION This chapter shows you how to quickly configure the basic functions of your SMCWGBR14-N2 Wireless N Gigabit Router using the Quick Setup Wizard. The default IP address of the SMCWGBR14-N2 Wireless N Gigabit Router is 192.168.2.1. And the default Subnet Mask is 255.255.255.0. These values can be changed as needed. In this guide, the default values are used for all descriptions. Connect a local PC to one of the LAN ports on the Router.
CHAPTER 3 | Quick Installation Guide TCP/IP Configuration Figure 4: Success Result of a Ping Command If the displayed result is similar to the following figure, it means the connection between your PC and the Router is not functioning. Figure 5: Failure of a Ping Command To check the connection, follow these steps: 1. Verify that the LAN port LED to which the PC is connected on the Router and the LED on your PC's network adapter are turned on. 2. Verify that the Router's IP address is 192.168.2.
CHAPTER 3 | Quick Installation Guide Quick Installation Guide QUICK INSTALLATION GUIDE With a Web-based (Internet Explorer or Netscape® Navigator) utility, it is easy to configure and manage the SMCWGBR14-N2 Wireless N Gigabit Router. The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web browser. 1. To access the configuration utility, open a web-browser and type the default address http://192.168.2.1 in the address field of the browser.
CHAPTER 3 | Quick Installation Guide Quick Installation Guide Figure 8: Quick Setup 3. Click Next, and then WAN Connection Type page will appear. Figure 9: Choose WAN Connection Type The Router provides Auto-Detect function and supports three popular ways PPPoE, Dynamic IP, and Static IP, to connect to the Internet. It is recommended that you make use of the Auto-Detect function.
CHAPTER 3 | Quick Installation Guide Quick Installation Guide ■ User Name and Password - Enter the User Name and Password provided by your ISP. These fields are case sensitive. If you have difficulty with this process, please contact your ISP. b. If the connection type detected is Dynamic IP, you can go on with the wireless configuration, as shown in Figure 12 on page 25. c. If the connection type detected is Static IP, the next screen will appear.
CHAPTER 3 | Quick Installation Guide Quick Installation Guide Figure 12: Quick Setup - Wireless Wireless Radio - Enable or disable the wireless radio choosing from the pull-down list. SSID - Enter a value of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. Considering your wireless network security, the default SSID is set to be “SMC”. This value is case-sensitive. For example, “TEST” is NOT the same as “test”.
CHAPTER 3 | Quick Installation Guide Quick Installation Guide Channel Width - Select any channel width from the pull-down list. The default setting is automatic, which can adjust the channel width for your clients automatically. Max Tx Rate - You can limit the maximum transmission rate of the Router through this field. Disable Security - The wireless security function can be enabled or disabled. If disabled, the wireless stations will be able to connect the Router without encryption.
CHAPTER 3 | Quick Installation Guide Quick Installation Guide Figure 14: Quick Setup - reboot – 27 –
4 CONFIGURING THE ROUTER This chapter will show each Web page's key functions and the configuration method. LOGIN After your successful login, you will see the twelve main menus on the left of the Web-based utility. On the right, there are the corresponding explanations and instructions. Figure 15: Main Menu The detailed explanations for each Web page’s key function are listed below.
CHAPTER 4 | Configuring the Router Status STATUS GENERAL STATUS The Status page provides the current status information about the Router. All information is read-only. Figure 16: Router Status ARP LIST To manage the computer, you could observe the computers in the LAN by checking the relationship of MAC address and IP address on the ARP list, and you could configure the items on the ARP list also. This page displays the ARP List; it shows all the existing IP & MAC Binding entrie.
CHAPTER 4 | Configuring the Router Quick Setup Figure 17: ARP List MAC Address - The MAC address of the controlled computer in the LAN. IP Address - The assigned IP address of the controlled computer in the LAN. Status - Indicates whether or not the MAC and IP addresses are bound. Configure - Load or delete an item. Load - Load the item to the IP & MAC Binding list. Delete - Delete the item. Click the Bind All button to bind all the current items, available after enable.
5 NETWORK SETTINGS There are five submenus under the Network menu: WAN, MAC Clone, LAN, Dynamic DNS and Binding Settings. Click any of them, and you will be able to configure the corresponding function. WAN Choose menu “Network->WAN”, you can configure the IP parameters of the WAN on the screen below. If your ISP provides the DHCP service, please choose Dynamic IP type, and the Router will automatically get IP parameters from your ISP. You can see the page as follows.
CHAPTER 5 | Network Settings WAN ◆ MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. It is not recommended that you change the default MTU Size unless required by your ISP. ◆ Use These DNS Servers - If your ISP gives you one or two DNS addresses, select Use These DNS Servers and enter the primary and secondary addresses into the correct fields. Otherwise, the DNS servers will be assigned dynamically from your ISP.
CHAPTER 5 | Network Settings WAN Primary/Secondary DNS - (Optional) Enter one or two DNS addresses in dotted-decimal notation provided by your ISP. If your ISP provides a PPPoE connection, select PPPoE option, then enter the following parameters: Figure 20: WAN-PPPoE User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. Secondary Connection - It’s available only for PPPoE Connection.
CHAPTER 5 | Network Settings WAN ◆ Connect on Demand - In this mode, the Internet connection can be terminated automatically after a specified inactivity period (Max Idle Time) and be re-established when you attempt to access the Internet again. If you want your Internet connection keeps active all the time, please enter “0” in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your Internet access disconnects.
CHAPTER 5 | Network Settings WAN ◆ MTU Size - The default MTU size is “1480” bytes, which is usually fine. It is not recommended that you change the default MTU Size unless required by your ISP. ◆ Service Name/AC Name - The service name and AC (Access Concentrator) name, which should not be configured unless you are sure it is necessary for your ISP. In most cases, leaving these fields blank will work.
CHAPTER 5 | Network Settings WAN ◆ User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. ◆ Auth Server - Enter the authenticating server IP address or host name. ◆ Auth Domain - Type in the domain suffix server name based on your location. For example: NSW / ACT - nsw.bigpond.net.au VIC / TAS / WA / SA / NT - vic.bigpond.net.au QLD - qld.bigpond.net.
CHAPTER 5 | Network Settings WAN If your ISP provides L2TP connection, please select L2TP option, then enter the following parameters : Figure 23: WAN-L2TP ◆ User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. ◆ Dynamic IP/ Static IP - Choose either as you are given by your ISP. Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately.
CHAPTER 5 | Network Settings WAN ◆ Connect Manually - You can configure the Router to make it connect or disconnect manually. After a specified period of inactivity (Max Idle Time), the Router will disconnect from your Internet connection, and you will not be able to re-establish your connection automatically as soon as you attempt to access the Internet again. To use this option, click the radio button.
CHAPTER 5 | Network Settings WAN ◆ Dynamic IP/ Static IP - Choose either as you are given by your ISP and enter the ISP’s IP address or the domain name. If you choose static IP and enter the domain name, you should also enter the DNS assigned by your ISP. And click the Save button. Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately.
CHAPTER 5 | Network Settings MAC Clone The Router can not detect PPTP/L2TP/BigPond connections with your ISP. If your ISP uses one of these protocols, then you must configure your connection manually. MAC CLONE Choose menu “Network->MAC Clone”, you can configure the MAC address of the WAN on the screen below: Figure 25: MAC Address Clone Some ISPs require that you register the MAC Address of your adapter. Changes are rarely needed here.
CHAPTER 5 | Network Settings LAN LAN Choose menu “Network->LAN”, you can configure the IP parameters of the LAN on the screen as below. Figure 26: LAN Settings ◆ MAC Address - The physical address of the Router, as seen from the LAN. The value can't be changed. ◆ IP Address - Enter the IP address of your Router or reset it in dotteddecimal notation (factory default: 192.168.2.1). ◆ Subnet Mask - An address code that determines the size of the network. Normally use 255.255.255.0 as the subnet mask.
CHAPTER 5 | Network Settings Dynamic DNS COMEXE.CN DDNS If the dynamic DNS Service Provider you select is www.comexe.cn, the page will appear. Figure 27: Comexe.cn DDNS Settings To set up for DDNS, follow these instructions: 1. Type the Domain Name received from your dynamic DNS service provider. 2. Type the User Name for your DDNS account. 3. Type the Password for your DDNS account. 4. Click the Login button to log in to the DDNS service.
CHAPTER 5 | Network Settings Dynamic DNS DYNDNS.ORG DDNS If the dynamic DNS Service Provider you select is www.dyndns.org, the page will appear. Figure 28: Dyndns.org DDNS Settings To set up for DDNS, follow these instructions: 1. Type the User Name for your DDNS account. 2. Type the Password for your DDNS account. 3. Type the Domain Name you received from dynamic DNS service provider here. 4. Click the Login button to log in to the DDNS service.
CHAPTER 5 | Network Settings Binding Setting NO-IP.COM DDNS If the dynamic DNS Service Provider you select is www.no-ip.com, the page will appear. Figure 29: No-ip.com DDNS Settings To set up for DDNS, follow these instructions: 1. Type the User Name for your DDNS account. 2. Type the Password for your DDNS account. 3. Type the Domain Name you received from dynamic DNS service provider. 4. Click the Login button to log in the DDNS service.
CHAPTER 5 | Network Settings Binding Setting ◆ MAC Address - The MAC address of the controlled computer in the LAN. ◆ IP Address - The assigned IP address of the controlled computer in the LAN. ◆ Bind - Check this option to enable ARP binding for a specific device. ◆ Modify - To modify or delete an existing entry. When you want to add or modify an IP & MAC Binding entry, you can click the Add New button or Modify button, and then you will go to the next page.
CHAPTER 5 | Network Settings Binding Setting Figure 32: Find IP & MAC Binding Entry Click the Enable All button to make all entries enabled. Click the Delete All button to delete all entries.
6 WIRELESS SETTINGS There are six submenus under the Wireless menu: Wireless Settings, Wireless Security, Wireless MAC Filtering, Wireless Advanced, Wireless Statistics and WPS. Click any of them, and you will be able to configure the corresponding function. WIRELESS SETTINGS Choose menu “Wireless->Wireless Setting”, you can configure the basic settings for the wireless network on this page. Figure 33: Wireless Settings ◆ SSID - Enter a value of up to 32 characters.
CHAPTER 6 | Wireless Settings Wireless Settings ◆ Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the Router can be used. It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance.
CHAPTER 6 | Wireless Settings Wireless Security NOTE: If 11b only, 11g only, or 11bg mixed is selected in the Mode field, the Channel Width selecting field will turn grey and the value will become 20M, which is unable to be changed. ◆ Max Tx Rate - You can limit the maximum tx rate of the Router through this field. ◆ Enable Wireless Router Radio - The wireless radio of this Router can be enabled or disabled to allow wireless stations access.
CHAPTER 6 | Wireless Settings Wireless Security Figure 35: Wireless Security Disable Security - If you do not want to use wireless security, select this check box, but it’s strongly recommended to choose one of the following modes to enable security. WEP - It is based on the IEEE 802.11 standard. If you select this check box, you will find a notice in red as show in the following figure.
CHAPTER 6 | Wireless Settings Wireless Security Figure 36: WEP ■ Type - you can choose the type for the WEP security on the pulldown list. The default setting is Automatic, which can select Open System or Shared Key authentication type automatically based on the wireless station's capability and request. ■ WEP Key Format - Hexadecimal and ASCII formats are provided. Hexadecimal format stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length.
CHAPTER 6 | Wireless Settings Wireless Security NOTE: If you check the WPA/WPA2 radio button and choose TKIP encryption, you will find a notice in red. Figure 37: WPA/WPA2 ◆ ■ Radius Server IP - Enter the IP address of the Radius Server. ■ Radius Port - Enter the port that radius service used. ■ Radius Password - Enter the password for the Radius Server. ■ Group Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update.
CHAPTER 6 | Wireless Settings Wireless MAC Filtering ■ PSK Passphrase - You can enter ASCII characters between 8 and 63 characters or 8 to 64 Hexadecimal characters. ■ Group Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update. Be sure to click the Save button to save your settings on this page.
CHAPTER 6 | Wireless Settings Wireless MAC Filtering Figure 40: Add or Modify Wireless MAC Address Filtering Entry To add or modify a MAC Address Filtering entry, follow these instructions: 1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit). For example: 00-0A-EB-00-07-8A. 2. Enter a simple description of the wireless station in the Description field. For example: Wireless station A. 3.
CHAPTER 6 | Wireless Settings Wireless Advanced 1. Click the Enable button to enable this function. 2. Select the radio button: Deny the stations not specified by any enabled entries in the list to access for Filtering Rules. 3. Delete all or disable all entries if there are any entries already. 4.
CHAPTER 6 | Wireless Settings Wireless Advanced ◆ RTS Threshold - Here you can specify the RTS (Request to Send) Threshold. If the packet is larger than the specified RTS Threshold size, the router will send RTS frames to a particular receiving station and negotiate the sending of a data frame. The default value is 2346. ◆ Fragmentation Threshold - This value is the maximum size determining whether packets will be fragmented.
CHAPTER 6 | Wireless Settings Wireless Statistics WIRELESS STATISTICS Choose menu “Wireless->Wireless Statistics”, you can see the MAC Address, Current Status, Received Packets and Sent Packets for each connected wireless station. Figure 43: Wireless Statistics MAC Address - The connected wireless station's MAC address. Current Status - The connected wireless station's running status, one of STA-AUTH / STA-ASSOC / STA-JOINED / WPA / WPA-PSK / WPA2 / WPA2-PSK / AP-UP / AP-DOWN / Disconnected.
CHAPTER 6 | Wireless Settings WPS Figure 44: WPS ◆ WPS Status - Enable or disable the WPS function here. ◆ Current PIN - The current value of the Router's PIN displayed here. The default PIN of the Router can be found in the label or User Guide. ◆ Restore PIN - Restore the PIN of the Router to its default. ◆ Gen New PIN - Click this button, and then you can get a new random value for the Router's PIN. You can ensure the network security by generating a new PIN.
CHAPTER 6 | Wireless Settings WPS Figure 45: WPS button 2. Press and hold the WPS button of the adapter directly for 2 or 3 seconds, then the adapter will connect to the router by WPS automatically. Figure 46: WPS button Method Two: 1. Press the WPS button on the front panel of the Router. Figure 47: WPS button 2. For the configuration of the wireless adapter, please choose Push the button on my access point in the configuration utility of the WPS as below, and click Next.
CHAPTER 6 | Wireless Settings WPS Figure 48: The WPS Configuration Screen of Wireless Adapter 3. Wait for a while until the next screen appears. Click Finish to complete the WPS configuration.
CHAPTER 6 | Wireless Settings WPS Method Three: 1. Keep the default WPS Status as Enabled and click the Add device button in Figure 44, then the following screen will appear. Figure 50: Add a New Device 2. Choose Press the button of the new device in two minutes and click Connect. 3. For the configuration of the wireless adapter, please choose Push the button on my access point in the configuration utility of the WPS as below, and click Next.
CHAPTER 6 | Wireless Settings WPS 4. Wait for a while until the next screen appears. Click Finish to complete the WPS configuration.
CHAPTER 6 | Wireless Settings WPS By PIN If the new device supports Wi-Fi Protected Setup and the PIN method, you can add it to the network by PIN with the following two methods. Method One: Enter the PIN into my Router 1. Keep the default WPS Status as Enabled and click the Add device button in Figure 44, then the following screen will appear. Figure 53: Add a New Device 2. Choose Enter the new device's PIN and enter the PIN code of the wireless adapter in the field behind PIN in the above figure.
CHAPTER 6 | Wireless Settings WPS Figure 54: The WPS Configuration Screen of Wireless Adapter NOTE: In this example, the default PIN code of this adapter is 26499123 as the above figure shown. Method Two: Enter the PIN from my Router 1. Get the Current PIN code of the Router. (Each router has its unique PIN code. Here takes the PIN code 12345670 of this Router for example). 2.
CHAPTER 6 | Wireless Settings WPS Figure 55: The WPS Configuration Screen of Wireless Adapter NOTE: The default PIN code of the Router can be found in its label or the WPS configuration screen as Figure 44. 3. Then the new device successfully connected to the network. NOTE: The status LED on the Router will light green all the time if the device has been successfully added to the network. The WPS function cannot be configured if the Wireless Function of the Router is disabled.
7 DHCP SETTINGS There are three submenus under the DHCP menu: DHCP Settings, DHCP Clients List and Address Reservation. Click any of them, and you will be able to configure the corresponding function. DHCP SETTINGS Choose menu “DHCP->DHCP Settings”, you can configure the DHCP Server on the page. The Router is set up by default as a DHCP (Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the PC(s) that are connected to the Router on the LAN.
CHAPTER 7 | DHCP Settings DHCP Clients List ◆ Address Lease Time - The Address Lease Time is the amount of time a network user will be allowed connection to the Router with their current dynamic IP Address. Enter the amount of time in minutes and the user will be "leased" this dynamic IP Address. After the time is up, the user will be automatically assigned a new dynamic IP address. The range of the time is 1 ~ 2880 minutes. The default value is 120 minutes. ◆ Default Gateway - (Optional.
