USER GUIDE BARRICADE™ N 300Mbps 4-Port Wireless Broadband Router SMCWBR14-N5
Wireless Broadband Router User Guide No. 1, Creation Road III, Hsinchu Science Park, 30077, Taiwan, R.O.C.
Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to change specifications at any time without notice. Copyright © 2012 by SMC Networks, Inc. No.
WARRANTY AND PRODUCT REGISTRATION To register SMC products and to review the detailed warranty statement, please refer to the Support Section of the SMC Website at http:// www.smc.com.
COMPLIANCES FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
Country Restriction Reason/Remark Norway Implemented This subsection does not apply for the geographical area within a radius of 20 km from the centre of NyÅlesund Russian Federation None Only for indoor applications NOTE: Do not use the product outdoors in France. EUROPE - EU DECLARATION OF CONFORMITY This device complies with the essential requirements of the R&TTE Directive 1999/5/EC.
In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services. This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 - 2483.5 MHz.
German Deutsch Hiermit erklärt SMC Networks, dass sich dieser/diese/dieses Radio LAN device in Übereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet". (BMWi) Hiermit erklärt SMC Networks die Übereinstimmung des Gerätes Radio LAN device mit den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie 1999/5/EG.
◆ Proper space for heat dissipation is necessary to avoid any damage caused by device overheating. The ventilation holes on the device are designed for heat dissipation to ensure that the device works normally. Do not cover these ventilation holes. ◆ Do not put this device close to a place where a heat source exits or high temperature occurs. Avoid placing the device in direct sunshine. ◆ Do not put this device close to a place which is damp or wet. Do not spill any fluid on this device.
SICHERHEITSMAßNAHMEN Lesen Sie vor der Inbetriebnahme des Gerätes aufmerksam die nachstehenden Informationen. Bitte befolgen Sie die nachstehenden Sicherheitsmaßnahmen, damit das Gerät nicht beschädigt wird oder Gefahren durch Brand oder elektrische Energie entstehen: ◆ Verwenden Sie nur das beim Gerät mitgelieferte Netzteil. ◆ Achten Sie auf die Last der Steckdose oder des Verlängerungskabels. Eine überlastete Steckdose oder beschädigte Kabel und Stecker können Stromschläge und Brand verursachen.
◆ Deje un espacio adecuado para que se disipe el calor y evitar así cualquier daño en el dispositivo causado por sobrecalentamiento. Los orificios de ventilación del dispositivo están diseñados para disipar el calor y garantizar que dicho dispositivo funciona con normalidad. No tape estos orificios de ventilación. ◆ No coloque este dispositivo cerca de un lugar donde haya una fuente de calor o temperaturas elevadas. Evite exponer el dispositivo a la luz solar directa.
BSMI NOTICE 在進行安裝及設定之前，建議您先閱讀以下注意事項： 1. 確認寬頻的線路是否正常：請先確認當 ADSL 或 Cable 或是對外的線路，直接結到您 的電腦時，是否能正常的連接到網際網路。 2. 移除撥號軟體：若您已經安裝 ISP 所提供的 ADSL 撥接（號）軟體，請先將其移除后 再開始進行連線設定。 3. 系統需求：本產品只需要使用網頁瀏覽器 （Browser）來進行設定安裝，不需要額 外安裝任何程式，在開始設定之前，建議您使用 Internet Explorer 6.0 或更新的 版本來進行安裝設定。 4. 設定時無需連上網際網路 （Internet），只需要透過區域連線 （LAN）即可進行設 定。 ※ 僅需從電腦端拉一條網路線連接至 SMCWBR14-N5 的 LAN 埠，WAN 埠則先不 要連上 ISP 線路。此動作作用是用來確認您可以正常連到此設備。 5.
ABOUT THIS GUIDE PURPOSE This guide details the hardware features of the wireless router, including its physical and performance-related characteristics, and how to install the device and use its configuration software. AUDIENCE This guide is for PC users with a working knowledge of computers. You should be familiar with Windows operating system concepts.
ABOUT THIS GUIDE ◆ Add BSMI Notice to the Compliances section. SEPTEMBER 2012 REVISION This is the fourth revision of this guide. It includes the following change: ◆ Updated the Compliances section. NOVEMBER 2011 REVISION This is the third revision of this guide. It includes the following change: ◆ Updated the Compliances section. SEPTEMBER 2011 REVISION This is the second revision of this guide. It includes the following change: ◆ Updated the Compliances section.
CONTENTS WARRANTY AND PRODUCT REGISTRATION 4 COMPLIANCES 5 ABOUT THIS GUIDE 14 CONTENTS 16 FIGURES 19 TABLES 23 1 INTRODUCTION 24 Overview of the Router 24 Main Features 25 Key Hardware Features 25 Package Contents 26 Front Panel 26 LED Indicators 26 WPS Button 27 Rear Panel 27 Wireless Antennas 27 Power 27 Ethernet WAN Port 28 Ethernet LAN Ports 28 2 CONNECTING THE ROUTER 29 System Requirements 29 Installation Environment Requirements 29 Connecting the Router 2
CONTENTS 4 CONFIGURING THE ROUTER 39 Login 39 Status 40 Quick Setup 41 WPS 41 Network 48 LAN 48 WAN 49 MAC Clone 59 Wireless 60 Wireless Settings (Router Mode) 60 Wireless Security 63 Wireless MAC Filtering 66 Wireless Advanced Wireless Statistics 69 70 DHCP 71 DHCP Settings 71 DHCP Clients List 72 Address Reservation 73 Forwarding 74 Virtual Servers 74 Port Triggering 76 DMZ 78 UPnP 79 Security 80 Basic Security 80 Advanced Security 82 Local Management
CONTENTS Bandwidth Control 98 Control Settings 98 Rules List 99 IP & MAC Binding 100 Binding Setting 100 ARP List 102 DDNS 103 System Tools 105 Time Settings 106 Diagnostic 108 Firmware Upgrade 109 Factory Defaults 110 Backup & Restore 111 Reboot 111 Password 112 System Log 113 Statistics 115 A CONFIGURING THE PC 117 Install TCP/IP Components B FAQ 117 121 How do I configure the Router for Internet access by ADSL users? 121 How do I configure the Router for Interne
FIGURES Figure 1: Front Panel 26 Figure 2: Rear Panel 27 Figure 3: Harewall Installation 30 Figure 4: Success Result of a Ping Command 32 Figure 5: Failure of a Ping Command 32 Figure 6: Log in to the Router 33 Figure 7: Windows Login 33 Figure 8: Quick Setup 34 Figure 9: Choose the WAN Connection Type 34 Figure 10: Quick Setup – PPPoE 35 Figure 11: Quick Setup - Static IP 35 Figure 12: Quick Setup – Wireless 36 Figure 13: Quick Setup – Finish 38 Figure 14: The Main Menu 39 Figu
CONTENTS Figure 32: WAN-Static IP 51 Figure 33: WAN-PPPoE 52 Figure 34: WAN-PPPoE Advanced Settings 54 Figure 35: WAN-BigPond Cable 55 Figure 36: WAN-L2TP 56 Figure 37: WAN-PPTP 58 Figure 38: MAC Address Clone 59 Figure 39: Wireless Menu 60 Figure 40: Wireless Settings 61 Figure 41: Note Dialog 61 Figure 42: Enable WDS 63 Figure 43: Wireless Security 63 Figure 44: WEP 64 Figure 45: WPA/WPA2-Enterprise 65 Figure 46: WPA/WPA2 - Personal(Recommended) 66 Figure 47: Wireless MAC Ad
CONTENTS Figure 68: Remote Management 84 Figure 69: Parental Control Settings 85 Figure 70: Add or Modify Parental Control Entry 87 Figure 71: Parental Control Settings 88 Figure 72: Access Control 88 Figure 73: Access Control Rule Management 89 Figure 74: Add or Modity Internet Access Control Entry 90 Figure 75: Host Settings 91 Figure 76: Add or Modify an IP Host Entry 92 Figure 77: Add or Modify a MAC Host Entry 92 Figure 78: Target Settings 93 Figure 79: Add or Modify an IP Access
CONTENTS Figure 104: Reboot 111 Figure 105: Password 112 Figure 106: System Log 113 Figure 107: Mail Account Settings 114 Figure 108: Statistics 115 Figure 109: TCP/IP 117 Figure 110: Internet Protocol 118 Figure 111: Internet Protocol Properties 119 Figure 112: Setting the IP Address Manually 120 Figure 113: PPPoE Connection Type 121 Figure 114: PPPoE Connection Mode 121 Figure 115: MAC Clone 122 Figure 116: Virtual Servers 123 Figure 117: Add or Modify a Virtual Server Entry 12
TABLES Table 1: Key Hardware Features 25 Table 2: LED Behavior 26 – 23 –
1 INTRODUCTION OVERVIEW OF THE ROUTER The Barricade™ SMCWBR14-N5 300Mbps 4-Port Wireless Broadband Router delivers exceptional range and speed, which can fully meet the needs of Small Office/Home Office (SOHO) networks and users demanding higher network performance. The router integrates a 4-port switch, firewall, NAT router, and wireless access point (AP). INCREDIBLE SPEED The SMCWBR14-N5 provides up to 300 Mbps wireless connections with other 802.
CHAPTER 1 | Introduction Main Features MAIN FEATURES ◆ IEEE 802.11n wireless technology provides a wireless data rate of up to 300 Mbps. ◆ One 10/100 Mbps Auto-Negotiation RJ-45 WAN port, four 10/100 Mbps Auto-Negotiation RJ-45 LAN ports, supporting Auto MDI/MDIX. ◆ Provides WPA/WPA2, WPA-PSK/WPA2-PSK authentication, TKIP/AES encryption security. ◆ Shares data and Internet access for users, supporting dynamic IP/static IP/PPPoE Internet access. ◆ Supports Virtual Server, Forwarding, and DMZ host.
CHAPTER 1 | Introduction Package Contents PACKAGE CONTENTS The following items should be found in your package: ◆ SMCWBR14-N5 300Mbps 4-Port Wireless Broadband Router, ◆ AC Power Adapter ◆ Quick Installation Guide ◆ Resource CD, including: ◆ This Guide ◆ Other Helpful Information NOTE: Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact with your distributor.
CHAPTER 1 | Introduction Rear Panel Table 2: LED Behavior (Continued) LED Status Description WAN LAN (1-4) On There is a device linked to the corresponding port, but there is no activity. Blinking There is an active device linked to the corresponding port. Off There is no device linked to the corresponding port. On A wireless device has been successfully added to the network by WPS. The LED will remain on for about 5 minutes.
CHAPTER 1 | Introduction Rear Panel ETHERNET WAN PORT This WAN port is where you connect the DSL/cable Modem. ETHERNET LAN LAN1,2,3,4: These ports (1, 2, 3, 4) connect the Router to local PCs.
2 CONNECTING THE ROUTER SYSTEM REQUIREMENTS You must meet the following minimum requirements: ◆ Broadband Internet Access Service (DSL/Cable/Ethernet) ◆ One DSL/Cable Modem that has an RJ-45 connector. ◆ PCs with working Ethernet adapters and Ethernet cables with RJ-45 connectors. ◆ TCP/IP protocol on each PC. ◆ Web browser, such as Microsoft Internet Explorer, Mozilla Firefox, or Apple Safari.
CHAPTER 2 | Connecting the Router Connecting the Router 2. Locate an optimum location for the Router. The best place is usually at the center of your network. The place must meet the Installation Environment Requirements. 3. Adjust the direction of the antennas. Normally, upright is the best direction. 4. Connect PCs and any switch in your LAN to the LAN Ports on the Router, as shown in Figure 3. 5. Connect the DSL/Cable Modem to the WAN port on the Router, as shown in Figure 3. 6.
3 QUICK INSTALLATION GUIDE This chapter shows you how to quickly configure the basic functions of your Router using the Quick Setup Wizard. TCP/IP CONFIGURATION The default IP address of the Router is 192.168.2.1. And the default Subnet Mask is 255.255.255.0. These values can be changed as you desire. In this guide, all the default values are used for descriptions. Connect local PCs to the LAN ports of the Router. And then you can configure the IP address for your PC in the following two ways.
CHAPTER 3 | Quick Installation Guide TCP/IP Configuration Figure 4: Success Result of a Ping Command If the result displayed is similar to Figure 5, it means the connection between your PC and the Router has failed. Figure 5: Failure of a Ping Command Follow these steps to check the connection: 1. Is the connection between your PC and the Router correct? The LAN port LED on the Router and the LED on your PC's adapter should be on. 2.
CHAPTER 3 | Quick Installation Guide Quick Installation Guide If the Router's IP address is 192.168.2.1, your PC's IP address must be within the range of 192.168.2.2 ~ 192.168.2.254. QUICK INSTALLATION GUIDE Using the Web-based utility, it is easy to configure and manage the Router. The Web-based utility can be used on any Windows, Macintosh, or UNIX system with a Web browser, such as Microsoft Internet Explorer, Mozilla Firefox, or Apple Safari. 1.
CHAPTER 3 | Quick Installation Guide Quick Installation Guide Figure 8: Quick Setup 3. Click Next. The WAN Connection Type page will appear, as shown in Figure 9. Figure 9: Choose the WAN Connection Type The Router provides an auto-detect function and supports three popular ways (PPPoE, Dynamic IP, and Static IP) to connect to the Internet. It is recommended that you make use of the auto-detect function.
CHAPTER 3 | Quick Installation Guide Quick Installation Guide Figure 10: Quick Setup – PPPoE ● User Name and Password — Enter the User Name and Password provided by your ISP. These fields are case sensitive. If you have difficulty with this process, contact your ISP. b. If the connection type detected is Dynamic IP, the screen shown in Figure 12 will display. You can then continue with the wireless configuration. c.
CHAPTER 3 | Quick Installation Guide Quick Installation Guide ● Secondary DNS - If your ISP provides another DNS server, enter it into this field. 5. Click Next to continue. The Wireless settings page will appear, as shown in Figure 12. Figure 12: Quick Setup – Wireless ■ Wireless Radio - Enable or disable the wireless radio choosing from the pull-down list. ■ Wireless Network Name - Enter a value of up to 32 characters.
CHAPTER 3 | Quick Installation Guide Quick Installation Guide ■ Channel Width - Select any channel width from the pull-down list. The default setting is automatic, which can adjust the channel width for your clients automatically. ■ Channel - This field determines which operating frequency will be used. The default channel is set to Auto, so the AP will choose the best channel automatically.
CHAPTER 3 | Quick Installation Guide Quick Installation Guide Figure 13: Quick Setup – Finish – 38 –
4 CONFIGURING THE ROUTER This chapter shows each Web page's key functions and the configuration method. LOGIN After successful login, you see the main menu on the left of the Web page. On the right, there are the corresponding explanations and instructions. Figure 14: The Main Menu The detailed explanations for each Web page’s key functions are listed below.
CHAPTER 4 | Configuring the Router Status STATUS The Status page provides the current status information about the Router. All information is read-only.
CHAPTER 4 | Configuring the Router Quick Setup QUICK SETUP Refer to “Quick Installation Guide” on page 31. WPS This section shows how to quickly add a new wireless device to an existing network using WPS (Wi-Fi Protected Setup). 1. Select WPS from the menu. You will see the next screen, as shown in Figure 16. Figure 16: WPS (Wi-Fi Protected Setup) ■ WPS Status - Enable or disable the WPS function here. ■ Current PIN - The current value of the Router's PIN is displayed here.
CHAPTER 4 | Configuring the Router WPS NOTE: To make a successful connection using WPS, you should also perform the corresponding WPS configuration on the new device. For the configuration of a new device, this example uses an SMC Wireless Adapter. BY PBC If the wireless adapter supports Wi-Fi Protected Setup and the Push Button Configuration (PBC) method, you can add it to the network by PBC with the following two methods. Method One: 1. Enable the WPS function from Web management page. 2.
CHAPTER 4 | Configuring the Router WPS Figure 19: WPS-Wireless Configuration Completed Method Two: 1. Enable the WPS function from Web management page. 2. Press the WPS button on the front panel of the Router. Figure 20: Front Panel 3. For the configuration of the wireless adapter, select “Push the button on my access point” in the WPS configuration, as below, and click Next.
CHAPTER 4 | Configuring the Router WPS Figure 21: WPS-Push the button on my access point 4. Wait until the next screen appears. Click Finish to complete the WPS configuration. Figure 22: WPS-Wireless Configuration Completed Method Three: 1. Keep the default WPS Status as Enabled and click the “Add device” button in Figure 23, then the following screen will appear.
CHAPTER 4 | Configuring the Router WPS Figure 23: Add A New Device 2. Select “Press the button of the new device in two minutes” and click Connect. 3. For the configuration of the wireless adapter, select “Push the button on my access point” in the WPS configuration utility, as below, and click Next. Figure 24: WPS-Push the button on my access point 4. Wait until the next screen appears. Click Finish to complete the WPS configuration.
CHAPTER 4 | Configuring the Router WPS Figure 25: WPS-Wireless Configuration Completed BY PIN If the new device supports Wi-Fi Protected Setup and the PIN method, you can add it to the network by PIN with the following two methods. Method One: Enter the PIN into my Router. 1. Keep the default WPS Status as Enabled and click the “Add device” button in Figure 26, then the following screen will appear. Figure 26: Add Device 2.
CHAPTER 4 | Configuring the Router WPS 3. For the configuration of the wireless adapter, selected “Enter a PIN into my access point or a registrar” in the WPS configuration, as below, and click Next. Figure 27: WPS-Enter a PIN into my access point NOTE: In this example, the default PIN code of the adapter is 16952898, as shown in the above figure. Method Two: Enter the PIN from my Router. 1. Read the Current PIN code of the Router in Figure 23 (each Router has its unique PIN code.
CHAPTER 4 | Configuring the Router Network Figure 28: WPS-Enter a PIN from my access point NOTE: The default PIN code of the Router can be found on its label, or in the WPS configuration screen, as shown in Figure 23. Then the new device successfully connected to the network. NOTE: The WPS LED on the Router will turn on green for five minutes when a device has been successfully added to the network. NOTE: The WPS function cannot be configured if the wireless function of the Router is disabled.
CHAPTER 4 | Configuring the Router Network Figure 30: LAN ◆ MAC Address - The physical address of the Router, as seen from the LAN. The value cannot be changed. ◆ IP Address - Enter the IP address of your Router or reset it in dotteddecimal notation (factory default: 192.168.2.1). ◆ Subnet Mask - An address code that determines the size of the network. Normally use 255.255.255.0 as the subnet mask. NOTE: If you change the IP Address of LAN, you must use the new IP Address to login the Router.
CHAPTER 4 | Configuring the Router Network Figure 31: WAN-Dynamic IP This page displays the WAN IP parameters assigned dynamically by your ISP, including IP address, Subnet Mask, Default Gateway, etc. Click the Renew button to renew the IP parameters from your ISP. Click the Release button to release the IP parameters. ◆ MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes.
CHAPTER 4 | Configuring the Router Network 2. If your ISP provides a static or fixed IP Address, Subnet Mask, Gateway and DNS setting, select Static IP. The Static IP settings page will appear, shown in Figure 32. Figure 32: WAN-Static IP ◆ IP Address - Enter the IP address in dotted-decimal notation provided by your ISP. ◆ Subnet Mask - Enter the subnet Mask in dotted-decimal notation provided by your ISP, usually is 255.255.255.0.
CHAPTER 4 | Configuring the Router Network Figure 33: WAN-PPPoE ◆ User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. ◆ Secondary Connection - It is available only for PPPoE Connection. If your ISP provides an extra Connection type such as Dynamic/Static IP to connect to a local area network, then you can check the radio button of Dynamic/Static IP to activate this secondary connection.
CHAPTER 4 | Configuring the Router Network ◆ Connect on Demand - In this mode, the Internet connection can be terminated automatically after a specified inactivity period (Max Idle Time) and be re-established when you attempt to access the Internet again. If you want your Internet connection keeps active all the time, please enter “0” in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your Internet access disconnects.
CHAPTER 4 | Configuring the Router Network Figure 34: WAN-PPPoE Advanced Settings ◆ MTU Size - The default MTU size is “1480” bytes, which is usually fine. It is not recommended that you change the default MTU Size unless required by your ISP. ◆ Service Name/AC Name - The service name and AC (Access Concentrator) name, which should not be configured unless you are sure it is necessary for your ISP. In most cases, leaving these fields blank will work.
CHAPTER 4 | Configuring the Router Network Figure 35: WAN-BigPond Cable ◆ User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. ◆ Auth Server - Enter the authenticating server IP address or host name. ◆ Auth Domain - Type in the domain suffix server name based on your location. For example: NSW / ACT - nsw.bigpond.net.au VIC / TAS / WA / SA / NT - vic.bigpond.net.au QLD - qld.bigpond.net.
CHAPTER 4 | Configuring the Router Network ◆ Connect Automatically - The connection can be re-established automatically when it was down. ◆ Connect Manually - You can click the Connect/Disconnect button to connect/disconnect immediately. This mode also supports the Max Idle Time function as Connect on Demand mode. The Internet connection can be disconnected automatically after a specified inactivity period and re-established when you attempt to access the Internet again.
CHAPTER 4 | Configuring the Router Network ◆ User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. ◆ Dynamic IP/ Static IP - Choose either as you are given by your ISP. Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately. ◆ Connect on Demand - You can configure the Router to disconnect from your Internet connection after a specified period of inactivity (Max Idle Time).
CHAPTER 4 | Configuring the Router Network Figure 37: WAN-PPTP ◆ User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. ◆ Dynamic IP/ Static IP - Choose either as you are given by your ISP and enter the ISP’s IP address or the domain name. If you choose static IP and enter the domain name, you should also enter the DNS assigned by your ISP. And click the Save button. Click the Connect button to connect immediately.
CHAPTER 4 | Configuring the Router Network ◆ Connect Automatically - Connect automatically after the Router is disconnected. To use this option, click the radio button. ◆ Connect Manually - You can configure the Router to make it connect or disconnect manually. After a specified period of inactivity (Max Idle Time), the Router will disconnect from your Internet connection, and you will not be able to re-establish your connection automatically as soon as you attempt to access the Internet again.
CHAPTER 4 | Configuring the Router Wireless Some ISPs require that you register the MAC Address of your adapter. Changes are rarely needed here. ◆ WAN MAC Address - This field displays the current MAC address of the WAN port. If your ISP requires you to register the MAC address, please enter the correct MAC address into this field in XX-XX-XX-XX-XXXX format (X is any hexadecimal digit). ◆ Your PC's MAC Address - This field displays the MAC address of the PC that is managing the Router.
CHAPTER 4 | Configuring the Router Wireless Figure 40: Wireless Settings ◆ Wireless Network Name - Enter a value of up to 32 characters. The same SSID (Service Set Identification) must be assigned to all wireless devices in your network. The default SSID is set to be “SMC”. This value is case-sensitive. For example, “TEST” is NOT the same as “test”. ◆ SSID (2-4) - Up to four SSIDs for each BSS can be set, the names can be up to 32 characters.
CHAPTER 4 | Configuring the Router Wireless NOTE: Limited by local law regulations, the version for North America does not have a region selection option. ◆ Mode - Select the operating mode. The default is 11b/g/n mixed. ■ 11b only - Select if all of your wireless clients are 802.11b. 11g only - Select if all of your wireless clients are 802.11g. 11n only- Select only if all of your wireless clients are 802.11n. 11b/g mixed - Select if you are using both 802.11b and 802.11g wireless clients.
CHAPTER 4 | Configuring the Router Wireless Figure 42: Enable WDS WIRELESS SECURITY Choose menu “Wireless->Wireless Security”; you can then configure the security settings of your wireless network. There are five wireless security modes supported by the Router: WEP (Wired Equivalent Privacy), WPA (Wi-Fi Protected Access), WPA2 (Wi-Fi Protected Access 2), WPA2-PSK (Pre-Shared Key), and WPA-PSK (PreShared Key).
CHAPTER 4 | Configuring the Router Wireless ◆ Disable Security - If you do not want to use wireless security, select this check box. However, it is strongly recommended to choose one of the following modes to enable security. ◆ WEP - This security is based on the IEEE 802.11 standard. If you select this check box, you will find a notice in red, as shown in Figure 44. Figure 44: WEP ■ Type - you can choose the type for the WEP security on the pulldown list.
CHAPTER 4 | Configuring the Router Wireless ■ Version - you can choose the version of the WPA security on the pull-down list. The default setting is Automatic, which can select WPA (Wi-Fi Protected Access) or WPA2 (WPA version 2) automatically based on the wireless station's capability and request. ■ Encryption - You can select either Automatic, TKIP, or AES. NOTE: If you check the WPA/WPA2 radio button and choose TKIP encryption, you will find a notice in red, as shown in Figure 45.
CHAPTER 4 | Configuring the Router Wireless Figure 46: WPA/WPA2 - Personal(Recommended) ■ PSK Passphrase - You can enter between 8 and 63 ASCII characters, or 8 to 64 Hexadecimal characters. ■ Group Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update. Be sure to click the Save button to save your settings on this page.
CHAPTER 4 | Configuring the Router Wireless To Add a Wireless MAC Address filtering entry, click the “Add New” button. The "Add or Modify Wireless MAC Address Filtering entry" page will appear, as shown in Figure 48: Figure 48: Add or Modify Wireless MAC Address Filtering Entry To add or modify a MAC Address Filtering entry, follow these instructions: 1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit).
CHAPTER 4 | Configuring the Router Wireless 1. Click the Enable button to enable this function. 2. Select the radio button: Deny the stations not specified by any enabled entries in the list to access for Filtering Rules. 3. Delete all or disable all entries if there are any entries already. 4. Click the Add New button. a. Enter the MAC address 00-0A-EB-00-07-8A /00-0A-EB-00-23-11 in the MAC Address field. b. Enter wireless station A/B in the Description field. c.
CHAPTER 4 | Configuring the Router Wireless WIRELESS ADVANCED Choose Wireless -> Wireless Advanced from the menu; you can then configure the advanced settings of your wireless network. Figure 50: Wireless Advanced ◆ Transmit Power - Here you can specify the transmit power of the Router. You can select High, Middle, or Low. High is the default setting and is recommended. ◆ Beacon Interval - Enter a value between 20-1000 milliseconds for the Beacon Interval.
CHAPTER 4 | Configuring the Router Wireless ◆ Enabled AP Isolation - This function can isolate wireless stations on your network from each other. Wireless devices will be able to communicate with the Router, but not with each other. To use this function, check this box. AP Isolation is disabled by default. NOTE: If you are not familiar with the settings on this page, it is strongly recommended to keep the default values; otherwise it may result in lower wireless network performance.
CHAPTER 4 | Configuring the Router DHCP DHCP There are three submenus under the DHCP menu (shown in Figure 52): DHCP Settings, DHCP Clients List, and Address Reservation. Click any of them, and you will be able to configure the corresponding function. Figure 52: The DHCP Menu DHCP SETTINGS Select DHCP -> DHCP Settings from the menu. You can configure the DHCP Server on the page, as shown in Figure 53.
CHAPTER 4 | Configuring the Router DHCP Enter the amount of time in minutes and the user will be “leased” this dynamic IP Address. After the time is up, the user will be automatically assigned a new dynamic IP address. The range of the time is 1 ~ 2880 minutes. The default value is 120 minutes. ◆ Default Gateway - (Optional.) Suggest to input the IP address of the LAN port of the Router, default value is 192.168.2.1 ◆ Default Domain - (Optional.) Input the domain name of your network.
CHAPTER 4 | Configuring the Router DHCP ◆ Lease Time - The time of the DHCP client leased. After the dynamic IP address has expired, a new dynamic IP address will be automatically assigned to the user. You cannot change any of the values on this page. To update this page and to show the current attached devices, click the Refresh button. ADDRESS Select DHCP -> Address Reservation from the menu; you can view and RESERVATION add reserved addresses for clients from the next screen (shown in Figure 55).
CHAPTER 4 | Configuring the Router Forwarding Figure 56: Add or Modify an Address Reservation Entry To modify or delete an existing entry: 1. Click Modify in the entry you want to modify. If you want to delete the entry, click the Delete. 2. Modify the information. 3. Click the Save button. 4. Click the Enable/Disable All button to enable/disable all entries. 5. Click the Delete All button to delete all entries. 6.
CHAPTER 4 | Configuring the Router Forwarding server must have a static or reserved IP Address because its IP Address may be changed when using the DHCP function. Figure 58: Virtual Servers ◆ Service Port - The number of an external port. You can type a service port or a range of service ports (in XXX – YYY format, XXX is the start port number, YYY is the end port number). ◆ IP Address - The IP Address of the PC providing the service application.
CHAPTER 4 | Configuring the Router Forwarding Figure 59: Add or Modify a Virtual Server Entry NOTE: If your computer or server has more than one type of available service, please select another service, and enter the same IP Address for that computer or server. To modify or delete an existing entry: 1. Click Modify for the entry you want to modify. If you want to delete the entry, click Delete. 2. Modify the information. 3. Click the Save button. 4.
CHAPTER 4 | Configuring the Router Forwarding Figure 60: Port Triggering Once the Router is configured, the operation is as follows: 1. A local host makes an outgoing connection using a destination port number defined in the Trigger Port field. 2. The Router records this connection, opens the incoming port or ports associated with this entry in the Port Triggering table, and associates them with the local host. 3.
CHAPTER 4 | Configuring the Router Forwarding 3. Select the protocol used for Trigger Port from the Trigger Protocol dropdown list, either TCP, UDP, or All. 4. Select the protocol used for Incoming Ports from the Incoming Protocol drop-down list, either TCP or UDP, or All. 5. Select Enable in Status field. 6. Click the Save button to save the new rule. Figure 61: Add or Modify a Triggering Entry To modify or delete an existing entry: 1. Click Modify in the entry you want to modify.
CHAPTER 4 | Configuring the Router Forwarding allows one local host to be exposed to the Internet for a special-purpose service such as Internet gaming or videoconferencing. DMZ host forwards all the ports at the same time. Any PC whose port is being forwarded must have its DHCP client function disabled and should have a new static IP Address assigned to it because its IP Address may be changed when using the DHCP function. Figure 62: DMZ To assign a computer or server to be a DMZ server: 1.
CHAPTER 4 | Configuring the Router Security ◆ Current UPnP Status - UPnP can be enabled or disabled by clicking the Enable or Disable button. As allowing this may present a risk to security, this feature is enabled by default. ◆ Current UPnP Settings List - This table displays the current UPnP information. ■ App Description - The description provided by the application in the UPnP request ■ External Port - External port, which the router opened for the application.
CHAPTER 4 | Configuring the Router Security Figure 65: Basic Security ◆ Firewall - A firewall protects your network from the outside world. Here you can enable or disable the Router’s firewall. ■ ◆ ◆ SPI Firewall - SPI (Stateful Packet Inspection, also known as dynamic packet filtering) helps to prevent cyber attacks by tracking states per session. It validates that the traffic passing through the session conforms to the protocol. SPI Firewall is enabled by factory default.
CHAPTER 4 | Configuring the Router Security port translation for certain application layer "control/data" protocols such as FTP, TFTP, H323 etc. ■ FTP ALG - To allow FTP clients and servers to transfer data across NAT, keep the default Enable. ■ TFTP ALG - To allow TFTP clients and servers to transfer data across NAT, keep the default Enable. ■ H323 ALG - To allow Microsoft NetMeeting clients to communicate across NAT, keep the default Enable.
CHAPTER 4 | Configuring the Router Security ◆ Packets Statistics Interval (5~60) - The default value is 10. Select a value between 5 and 60 seconds from the drop-down list. The Packets Statistics Interval value indicates the time section of the packets statistics. The result of the statistics is used for analysis by SYN Flood, UDP Flood and ICMP-Flood. ◆ DoS Protection - Denial of Service protection. Check the Enable or Disable button to enable or disable the DoS protection function.
CHAPTER 4 | Configuring the Router Security LOCAL MANAGEMENT Select Security->Local Management from the menu; you can configure the management rules in the screen, as shown in Figure 67. The management feature allows you to deny computers in the LAN from accessing the Router. Figure 67: Local Management By default, the radio button “All the PCs on the LAN are allowed to access the Router's Web-Based Utility” is checked.
CHAPTER 4 | Configuring the Router Parental Control ◆ Web Management Port - Web browser access normally uses the standard HTTP service port 80. This Router's default remote management web port number is 80. For greater security, you can change the remote management web port to a custom port by entering that number in the box provided. Choose a number between 1 and 65534, but do not use the number of any common service port.
CHAPTER 4 | Configuring the Router Parental Control ◆ Parental Control - Check Enable if you want this function to take effect, otherwise check Disable. ◆ MAC Address of Parental PC - In this field, enter the MAC address of the controlling PC, or you can make use of the “Copy To Above” button below. ◆ MAC Address of Your PC - This field displays the MAC address of the PC that is managing this Router.
CHAPTER 4 | Configuring the Router Parental Control Figure 70: Add or Modify Parental Control Entry For example: If you desire that the child PC with MAC address 00-11-2233-44-AA can access www.google.com on Saturday only while the parent PC with MAC address 00-11-22-33-44-BB is without any restriction, you should follow the settings below. 1. Click Parental Control on the menu to enter the Parental Control Settings page.
CHAPTER 4 | Configuring the Router Access Control 4. Click Save to complete the settings. Then you will go back to the Parental Control Settings page and see the following list, as shown in Figure 71. Figure 71: Parental Control Settings ACCESS CONTROL There are four submenus under the Access Control menu as shown in Figure 72: Rule, Host, Target, and Schedule. Click any of them, and you will be able to configure the corresponding function.
CHAPTER 4 | Configuring the Router Access Control Figure 73: Access Control Rule Management ◆ Enable Internet Access Control - Select the check box to enable the Internet Access Control function, so the Default Filter Policy can take effect. ◆ Rule Name - Here displays the name of the rule and this name is unique. ◆ Host - Here displays the host selected in the corresponding rule. ◆ Target - Here displays the target selected in the corresponding rule.
CHAPTER 4 | Configuring the Router Access Control 5. Select a schedule from the Schedule drop-down list or choose “Click Here To Add New Schedule”. 6. In the Action field, select Deny or Allow. 7. In the Status field, select Enabled or Disabled to enable or disable your entry. Click the Save button. Click the Enable All button to enable all the rules in the list. Click the Disable All button to disable all the rules in the list. Click the Delete All button to delete all the entries in the table.
CHAPTER 4 | Configuring the Router Access Control Schedule_1, Day is Sat and Sun, Start Time is 1800 and Stop Time is 2000. 4. Click “Access Control->Rule” in the left to return to the Access Control Rule Management page. Select “Enable Internet Access Control” and choose "Deny the packets not specified by any access control policy to pass through the Router". 5. Click the “Add New” button to add a new rule as follows: ■ In Rule Name field, create a name for the rule.
CHAPTER 4 | Configuring the Router Access Control To add a new entry, please follow the steps below. 1. Click the “Add New” button. 2. In the Mode field, select IP Address or MAC Address. ■ ■ If you select IP Address, the screen in Figure 76 is displayed. ● In the Host Description field, create a unique description for the host (e.g. Host_1). ● In LAN IP Address field, enter the IP address. If you select MAC Address, the screen in Figure 77 is displayed.
CHAPTER 4 | Configuring the Router Access Control 1. Click “Add New” button in Figure 75 to enter the “Add or Modify a Host Entry” page. 2. In Mode field, select MAC Address from the drop-down list. 3. In Host Description field, create a unique description for the host (e.g. Host_1). 4. In MAC Address field, enter 00-11-22-33-44-AA. 5. Click Save to complete the settings. Then you will go back to the Host Settings page and see the following list.
CHAPTER 4 | Configuring the Router Access Control Common Service Port drop-down list doesn’t have the service you want, specify the Target Port manually. ● In Protocol field, select TCP, UDP, ICMP or ALL. b. If you select Domain Name, the screen in Figure 80 is shown. ● In Target Description field, create a unique description for the target (e.g. Target_1). ● In Domain Name field, enter the domain name, either the full name or the keywords (for example google) in the blank.
CHAPTER 4 | Configuring the Router Access Control For example: If you desire to restrict the internet activities of a host with MAC address 00-11-22-33-44-AA in the LAN to access www.google.com only, you should first follow the settings below: 1. Click the “Add New” button in Figure 78 to enter the Add or Modify an Access Target Entry page. 2. In Mode field, select Domain Name from the drop-down list. 3. In Target Description field, create a unique description for the target (e.g. Target_1). 4.
CHAPTER 4 | Configuring the Router Access Control ◆ Modify - Here you can edit or delete an existing schedule. To add a new schedule, follow the steps below. 1. Click the “Add New” button shown in Figure 82 and the next screen will pop-up as shown in Figure 83. 2. In Schedule Description field, create a unique description for the schedule (e.g. Schedule_1). 3. In Day field, select the day or days you need. 4.
CHAPTER 4 | Configuring the Router Advanced Routing 4. In Time field, enter 1800 in Start Time field and 2000 in Stop Time field. 5. Click Save to complete the settings. Then you will go back to the Schedule Settings page and see the following list. ADVANCED ROUTING Select static routing list from the menu; you can configure the static route in the next screen (Figure 84). A static route is a pre-determined path that network information must travel to reach a specific host or network.
CHAPTER 4 | Configuring the Router Bandwidth Control ◆ Subnet Mask - The Subnet Mask determines which portion of an IP Address is the network portion, and which portion is the host portion. ◆ Gateway - This is the IP Address of the gateway device that allows for contact between the Router and the network or host. 3. Select Enabled or Disabled for this entry on the Status pull-down list. 4. Click the Save button to make the entry take effect.
CHAPTER 4 | Configuring the Router Bandwidth Control ◆ Egress Bandwidth - The upload speed through the WAN port. ◆ Ingress Bandwidth - The download speed through the WAN port. RULES LIST Select Bandwidth Control->Rules List from the menu; you can view and configure the bandwidth control rules in the screen below. ◆ Description - This is the information about the rules such as address range.
CHAPTER 4 | Configuring the Router IP & MAC Binding Figure 88: Rule Settings IP & MAC BINDING There are two submenus under the IP &MAC Binding menu (shown in Figure 90): Binding Settings and ARP List. Click any of them, and you will be able to scan or configure the corresponding function. The detailed explanations for each submenu are provided below.
CHAPTER 4 | Configuring the Router IP & MAC Binding ◆ MAC Address - The MAC address of the controlled computer in the LAN. ◆ IP Address - The assigned IP address of the controlled computer in the LAN. ◆ Bind - Check this option to enable ARP binding for a specific device. ◆ Modify - To modify or delete an existing entry. When you want to add or modify an IP & MAC Binding entry, you can click the “Add New” button or “Modify” button, and then you will go to the next page.
CHAPTER 4 | Configuring the Router IP & MAC Binding Figure 92: Find IP & MAC Binding Entry Click the “Enable All” button to make all entries enabled. Click the “Delete All” button to delete all entries. ARP LIST Select IP & MAC Binding->ARP List from the menu; you can view and set ARP List in the screen, as shown in Figure 93.
CHAPTER 4 | Configuring the Router DDNS Click the Load All button to load all items to the IP & MAC Binding list. Click the Refresh button to refresh all items. NOTE: An item could not be loaded to the IP & MAC Binding list if the IP address of the item has been loaded before. Error warning will prompt as well. Likewise, "Load All" only loads the items without interference to the IP & MAC Binding list. DDNS Choose menu “DDNS”, and you can configure the DDNS function.
CHAPTER 4 | Configuring the Router DDNS 2. Type the User Name for your DDNS account. 3. Type the Password for your DDNS account. 4. Click the Login button to log in to the DDNS service. ◆ Connection Status -The status of the DDNS service connection is displayed here. NO-IP.COM DDNS If the DDNS Service Provider you select is www.no-ip.com, the page will appear as shown in Figure 95. Figure 95: No-ip.com DDNS Settings ◆ Connection Status - The status of the DDNS service connection is displayed here.
CHAPTER 4 | Configuring the Router System Tools Figure 96: Comexe.cn DDNS Settings ◆ Connection Status - The status of the DDNS service connection is displayed here. ◆ Click Logout to log out the DDNS service. To set up for DDNS, follow these instructions: 1. Type the User Name for your DDNS account. 2. Type the Password for your DDNS account. 3. Type the Domain Name you received from DDNS service provider. Click the Login button to log in the DDNS service.
CHAPTER 4 | Configuring the Router System Tools Figure 97: The System Tools Menu TIME SETTINGS Select System Tools->Time Setting from the menu; you can configure the time on the following screen. Figure 98: Time Settings ◆ Time Zone - Select your local time zone from this pull down list. ◆ Date - Enter your local date in MM/DD/YY into the right blanks. ◆ Time - Enter your local time in HH/MM/SS into the right blanks.
CHAPTER 4 | Configuring the Router System Tools ◆ Start -The time to start the Daylight Saving. Select the month in the first field, the week in the second field, the day in the third field and the time in the last field. ◆ End -The time to end the Daylight Saving. Select the month in the first field, the week in the second field, the day in the third field and the time in the last field. ◆ Daylight Saving Status -Displays the status whether the Daylight Saving is in use.
CHAPTER 4 | Configuring the Router System Tools DIAGNOSTIC Select System Tools->Diagnostic from the menu; you can use Ping or Traceroute functions to check connectivity of your network in the following screen. Figure 99: Diagnostic Tools ◆ Diagnostic Tool - Check the radio button to select one diagnostic too. ■ Ping - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway. ■ Traceroute - This diagnostic tool tests the performance of a connection.
CHAPTER 4 | Configuring the Router System Tools ◆ Traceroute Max TTL - The max number of hops for a Traceroute connection. Click Start to check the connectivity of the Internet. The Diagnostic Results page displays the result of diagnosis. If the result is similar to the following screen, the connectivity of the Internet is fine. Figure 100: Diagnostic Results NOTE: Only one user can use this tool at one time. Options “Number of Pings”, “Ping Size” and “Ping Timeout” are used for the Ping function.
CHAPTER 4 | Configuring the Router System Tools To upgrade the Router's firmware, follow the instructions below: 1. Download a more recent firmware upgrade file from the SMC website (http://www.smc.com). 2. Type the path and file name of the update file into the File field. Or click the Browse button to locate the update file. 3. Click the Upgrade button. NOTE: New firmware versions are posted at http://www.smc.com and can be downloaded for free.
CHAPTER 4 | Configuring the Router System Tools NOTE: Any settings you have saved will be lost when the default settings are restored. NOTE: When press and hold the WPS Button for more than 5 seconds, you will reset the router. BACKUP & RESTORE Select System Tools-> Backup & Restore from the menu; you can save the current configuration of the Router as a backup file and restore the configuration via a backup file as shown in Figure 103.
CHAPTER 4 | Configuring the Router System Tools Some settings of the Router will take effect only after rebooting, which include ◆ Change of the LAN IP Address (system will reboot automatically). ◆ Change of DHCP Settings. ◆ Change of Wireless configurations. ◆ Change of the Web Management Port. ◆ Upgrade of the Router firmware (system will reboot automatically). ◆ Restore the Router's settings to factory defaults (system will reboot automatically).
CHAPTER 4 | Configuring the Router System Tools SYSTEM LOG Selct System Tools->System Log from the menu; you can view the logs of the Router. Figure 106: System Log ◆ Auto Mail Feature - Indicates whether auto mail feature is enabled or not. ◆ Mail Settings - Set the receiving and sending mailbox address, server address, validation information as well as the timetable for Auto Mail Feature, as shown in Figure 107. ◆ Log Type - By selecting the log type, only logs of this type will be shown.
CHAPTER 4 | Configuring the Router System Tools Figure 107: Mail Account Settings ◆ From - Your mail box address. The Router would connect it to send logs. ◆ To - Recipient’s address. The destination mailbox where the logs would be received. ◆ SMTP Server - Your smtp server. It corresponds with the mailbox filled in the From field. You can log on the relevant website for Help if you are not clear with the address. ◆ Authentication - Most SMTP Server requires Authentication.
CHAPTER 4 | Configuring the Router System Tools Click the Next button to go to the next page, or click the Previous button return to the previous page. STATISTICS Select System Tools->Statistics from the menu; you can view the statistics of the Router, including total traffic and current traffic of the last Packets Statistic Interval. Figure 108: Statistics ◆ Current Statistics Status - Enable or Disable. The default value is disabled. To enable, click the Enable button.
CHAPTER 4 | Configuring the Router System Tools Current Packets - The total amount of packets received and transmitted in the last Packets Statistic interval seconds. Current Bytes - The total amount of bytes received and transmitted in the last Packets Statistic interval seconds. Current ICMP Tx - The total amount of the ICMP packets transmitted to WAN in the last Packets Statistic interval seconds.
A CONFIGURING THE PC The section shows how to install and configure TCP/IP settings correctly in Windows XP. First make sure your Ethernet Adapter is working, refer to the adapter’s manual if needed. INSTALL TCP/IP COMPONENTS 1. On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel. 2. Click the Network and Internet Connections icon, and then click on the Network Connections tab in the following window. 3.
APPENDIX A | Configuring the PC Install TCP/IP Components Figure 110: Internet Protocol 5. The following TCP/IP Properties window will display and the IP Address tab is open on this window by default. Now you have two ways to configure the TCP/IP protocol below: a. Set the IP address automatically.
APPENDIX A | Configuring the PC Install TCP/IP Components Figure 111: Internet Protocol Properties b. Set the IP address manually. Select “Use the following IP address” radio button and enter the following items: — If the Router's LAN IP address is 192.168.2.1, type an IP address such as 192.168.2.x (where x is from 2 to 254), and Subnet mask as 255.255.255.0. — Type the Router’s LAN IP address (the default IP is 192.168.2.1) into the Default gateway field.
APPENDIX A | Configuring the PC Install TCP/IP Components Figure 112: Setting the IP Address Manually 2 2 6. Click OK to keep your settings.
B FAQ HOW DO I CONFIGURE THE ROUTER FOR INTERNET ACCESS BY ADSL USERS? 1. Configure the ADSL Modem in RFC1483 bridge mode. 2. Connect Ethernet cable from the ADSL Modem to the WAN port on the Router. The telephone cord plugs into the Line port of the ADSL Modem. 3. Log in to the Router, click “Network” on the web page menu and then click “WAN” on the submenu. a. On the WAN page, select “PPPoE” for the WAN connection type. b.
APPENDIX B | FAQ How do I configure the Router for Internet access by Ethernet users? NOTE: Sometimes the connection cannot be disconnected although you have specified a Max Idle Time, since some applications may be visiting the Internet continually in the background. NOTE: If you are a Cable user, configure the Router following the above steps. HOW DO I CONFIGURE THE ROUTER FOR INTERNET ACCESS BY ETHERNET USERS? 1.
APPENDIX B | FAQ I want to use Netmeeting, what do I need to do? I WANT TO USE NETMEETING, WHAT DO I NEED TO DO? 1. If you start Netmeeting as a host, you do not need to change anything on the Router. 2. If you start as a response, you need to configure a Virtual Server or DMZ Host, and make sure the H323 ALG is enabled. 3. Configure a Virtual Server: a. Log in to the Router, click “Forwarding” on the menu, and then click "Virtual Servers" on the submenu. b.
APPENDIX B | FAQ I want to use Netmeeting, what do I need to do? NOTE: The other party should call your WAN IP, which is displayed on the “Status” page. 4. Enable a DMZ Host: a. Log in to the Router, click “Forwarding” on the menu, and then click “DMZ” on the submenu. b. On the "DMZ" page, click the Enable radio button. c. Type your IP address into the “DMZ Host IP Address” field (for example, 192.168.2.169). d. Click the Save button. Figure 118: DMZ 5. Enable the H323 ALG: a.
APPENDIX B | FAQ I want to build a WEB Server on the LAN, what should I do? Figure 119: Basic Security I WANT TO BUILD A WEB SERVER ON THE LAN, WHAT SHOULD I DO? 1. Change the Web management port number: Because the Web Server port 80 will interfere with the Web management port 80 on the Router, you must change the Web management port number to avoid interference. a. Log in to the Router, click “Security” on the menu, and then click "Remote Management" on the submenu. b.
APPENDIX B | FAQ Wireless stations cannot connect to the Router a. Log in to the Router, click “Forwarding” on the menu, and then click "Virtual Servers" on the submenu. b. On the "Virtual Servers" page, click “Add New”. c. On the “Add or Modify a Virtual Server” page, enter “80” into the field for the “Service Port”. d. Enter your IP address in the “IP Address” field (for example, 192.168.2.188). e. Set to Enable and then Save.
APPENDIX B | FAQ Wireless stations cannot connect to the Router 4. If the wireless connection is ready, but you cannot access the Router, check the IP Address of your wireless station.
C SPECIFICATIONS STANDARDS IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX 802.11b 802.11g 802.
APPENDIX C | Specifications SECURITY WEP/WPA/WPA2/WPA2-PSK/WPA-PSK SENSITIVITY @PER 270 Mbps: -68dBm@10% PER 130 Mbps: -68dBm@10% PER 108 Mbps: -68dBm@10% PER 54 Mbps: -68dBm@10% PER 11 Mbps: -85dBm@8% PER 6 Mbps: -88dBm@10% PER 1 Mbps: -90dBm@8% PER ANTENNA GAIN 5dBi TEMPERATURE Operating: 0 °C to 40 °C (32 to 104 °F) Storage: -40 °C to 70 °C (-40 to 158 °F) HUMIDITY Operating: 10% to 90% (non-condensing) Storge: 5%-90% (non-condensing) – 129 –
GLOSSARY IEEE 802.11B A wireless standard that supports wireless communications in the 2.4 GHz band using Direct Sequence Spread Spectrum (DSSS). The standard provides for data rates of 1, 2, 5.5, and 11 Mbps. IEEE 802.11G A wireless standard that supports wireless communications in the 2.4 GHz band using Orthogonal Frequency Division Multiplexing (OFDM). The standard provides for data rates of 6, 9, 12, 18, 24, 36, 48, 54 Mbps. IEEE 802.11g is also backward compatible with IEEE 802.11b. IEEE 802.
GLOSSARY ISP (INTERNET SERVICE A company that provides access to the Internet. PROVIDER) MTU (MAXIMUM The size in bytes of the largest packet that can be transmitted. TRANSMISSION UNIT) NAT (NETWORK NAT technology translates IP addresses of a local area network to a ADDRESS TRANSLATION) different IP address for the Internet. PPPOE (POINT TO POINT PPPoE is a protocol for connecting remote hosts to the Internet over an PROTOCOL OVER always-on connection by simulating a dial-up connection.
INDEX A K AC power adapter 30 antennas 27 key features 25 L B DDNS 103 default IP 31 diagnostic tools 108 DNS addresses 50 Dynamic IP 52 LAN LED 27 LAN ports 28 LED indicators 26, 27 LEDs LAN 27 Power 26 System 26 WAN 27 WLAN 26 WPS 27 local management 84 location of router 30 logging in, web 33 login page 39 login password 35 logs, system 113 E M basic setup, wizard 41 C channel, operating 37 connections, router 29 contents of package 26 D environment requirements 29 Ethernet port 28 F facto
INDEX Power LED 26 proxy, web setting 33 Q quick setup 34 R radio channel 37 radio enable 36 region setting,country setting 36 remote management 84 requirements, system 29 router status 40 S setup wizard steps 41 setup, quick 34 SMTP server 114 software upgrade 109 specifications, hardware 128 Static IP 52 statistics 115 status information 40 System LED 26 system logs 113 system requirements 29 T TCP/IP configuration 31 TCP/IP settings 117 temperature, operating 29 U upgrading software 109 user name,
Headquarters No. 1, Creation Rd. III Hsinchu Science Park Taiwan 30077 Tel: +886 3 5638888 Fax: +886 3 6686111 (for Asia-Pacific): Technical Support information at www.smc-asia.com www.smcnetworks.co.kr SMCWBR14S-N5, SMCWBR14-N5 www.smc.
