User's Manual
Table Of Contents
- Warranty and Product Registration
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Command Line Interface
- Using the Command Line Interface
- General Commands
- System Management Commands
- country
- prompt
- system name
- system-resource
- password
- reboot-schedule
- apmgmgtui ssh enable
- apmgmtui ssh port
- apmgmtui telnet- server enable
- apmgmtui http port
- apmgmtui http server
- apmgmtui http session-timeout
- apmgmtui https port
- apmgmtui https server
- apmgmtui snmp
- apmgmtip
- show apmanagement
- show system
- show system resource
- show version
- show config
- System Logging Commands
- System Clock Commands
- DHCP Relay Commands
- SNMP Commands
- snmp-server community
- snmp-server contact
- snmp-server location
- snmp-server enable server
- snmp-server host
- snmp-server trap
- snmp-server vacm view
- snmp-server vacm group
- snmp-server user
- snmp-server target
- snmp-server filter
- show snmp users
- show snmp target
- show snmp filter
- show snmp
- show snmp vacm view
- show snmp vacm group
- Flash/File Commands
- RADIUS Client Commands
- 802.1X Authentication Commands
- MAC Address Authentication Commands
- Filtering Commands
- Spanning Tree Commands
- bridge stp service
- bridge stp br-conf forwarding-delay
- bridge stp br-conf hello-time
- bridge stp br-conf max-age
- bridge stp br-conf priority
- bridge stp port-conf interface
- bridge-link path-cost
- bridge-link port- priority
- vap (STP Interface)
- path-cost (STP Interface)
- port-priority (STP Interface)
- bridge mac-aging
- show bridge stp
- show bridge br-conf
- show bridge port-conf interface
- show bridge status
- show bridge forward address
- show bridge mac- aging
- WDS Bridge Commands
- Ethernet Interface Commands
- Wireless Interface Commands
- interface wireless
- vap
- a-mpdu
- a-msdu
- channel
- transmit-power
- min-allowed-rate
- disable-coexist
- make-rf-setting- effective
- preamble
- short-guard-interval
- beacon-interval
- dtim-period
- rts-threshold
- ssid
- closed-system
- max-client
- max-association
- client-assoc-preempt
- assoc-timeout- interval
- auth-timeout-interval
- multicast-enhance
- shutdown (VAP)
- interfere-chan- recover
- antenna-chain
- long-distance
- long-distance reference-data
- long-distance slottime
- long-distance acktimeout
- long-distance ctstimeout
- bandwidth-control downlink
- bandwidth-control downlink rate
- bandwidth-control uplink
- bandwidth-control uplink rate
- show interface wireless
- show station
- show station statistics
- Wireless Security Commands
- Rogue AP Detection Commands
- Link Integrity Commands
- Link Layer Discovery Commands
- VLAN Commands
- WMM Commands
- QoS Commands
- Appendices
- Index of CLI Commands
- Index
Chapter 2
| Initial Configuration
Web Quick Start
– 28 –
Caution:
You must set the country code to the country of operation. Setting the
country code restricts operation of the access point to the radio channels and
transmit power levels permitted for wireless networks in the specified country.
◆ Cancel — Cancels the newly entered settings and restores the orignals.
◆ Next — Proceeds to the next page.
Step 2 The Step 2 page of the Quick Start configures IP settings and DHCP client status.
Figure 6: Quick Start - Step 2
The following items are displayed on this page:
DHCP
◆ DHCP Status — Enables/disables DHCP on the access point. (Default: Disabled)
◆ IP Address — Specifies an IP address for the access point. Valid IP addresses
consist of four decimal numbers, 0 to 255, separated by periods. (Default:
192.168.2.10.)
◆ Subnet Mask — Indicates the local subnet mask. Select the desired mask from
the drop down menu. (Default: 255.255.255.0)
◆ Default Gateway — The default gateway is the IP address of the router for the
access point, which is used if the requested destination address is not on the
local subnet. (Default: 192.168.2.254)
If you have DNS, RADIUS, or other network servers located on another subnet,
type the IP address of the default gateway router in the text field provided.