Web Management Guide-R02
Table Of Contents
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Using the Web Interface
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Configuring CPU Guard
- Displaying Memory Utilization
- Resetting the System
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA (Authentication, Authorization and Accounting)
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- DHCP Snooping
- DHCPv6 Snooping
- ND Snooping
- IPv4 Source Guard
- IPv6 Source Guard
- ARP Inspection
- Application Filter
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting Community Access Strings
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Setting a Time Range
- Ethernet Ring Protection Switching
- MLAG Configuration
- OAM Configuration
- LBD Configuration
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query for IPv4)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering IGMP Packets on an Interface
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Configuring MLD Snooping and Query Parameters
- Setting Immediate Leave Status for MLD Snooping per Interface
- Specifying Static Interfaces for an IPv6 Multicast Router
- Assigning Interfaces to IPv6 Multicast Services
- Filtering MLD Query Packets on an Interface
- Showing MLD Snooping Groups and Source List
- Displaying MLD Snooping Statistics
- Filtering and Throttling MLD Groups
- Multicast VLAN Registration for IPv4
- IP Tools
- IP Configuration
- General IP Routing
- IP Services
- Appendices
Chapter 16
| IP Configuration
Setting the Switch’s IP Address (IP Version 6)
– 619 –
Web Interface
To show neighboring IPv6 devices:
1. Click IP, IPv6 Configuration.
2. Select Show IPv6 Neighbors from the Action list.
Figure 410: Showing IPv6 Neighbors
State The following states are used for dynamic entries:
◆
Incomplete - Address resolution is being carried out on the entry.
A neighbor solicitation message has been sent to the multicast address of
the target, but it has not yet returned a neighbor advertisement message.
◆
Invalid - An invalidated mapping. Setting the state to invalid dis-associates
the interface identified with this entry from the indicated mapping (RFC
4293).
◆
Reachable - Positive confirmation was received within the last
ReachableTime interval that the forward path to the neighbor was
functioning. While in Reachable state, the device takes no special action
when sending packets.
◆
Stale - More than the ReachableTime interval has elapsed since the last
positive confirmation was received that the forward path was functioning.
While in Stale state, the device takes no action until a packet is sent.
◆
Delay - More than the ReachableTime interval has elapsed since the last
positive confirmation was received that the forward path was functioning. A
packet was sent within the last DELAY_FIRST_PROBE_TIME interval. If no
reachability confirmation is received within this interval after entering the
Delay state, the switch will send a neighbor solicitation message and
change the state to Probe.
◆
Probe - A reachability confirmation is actively sought by re-sending
neighbor solicitation messages every RetransTimer interval until
confirmation of reachability is received.
◆
Unknown - Unknown state.
The following states are used for static entries:
◆
Incomplete - The interface for this entry is down.
◆
Permanent - Indicates a static entry.
◆
Reachable - The interface for this entry is up. Reachability detection is not
applied to static entries in the IPv6 neighbor discovery cache.
VLAN VLAN interface from which the address was reached.
Table 38: Show IPv6 Neighbors - display description (Continued)
Field Description