Web Management Guide-R02
Table Of Contents
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Using the Web Interface
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Configuring CPU Guard
- Displaying Memory Utilization
- Resetting the System
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA (Authentication, Authorization and Accounting)
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- DHCP Snooping
- DHCPv6 Snooping
- ND Snooping
- IPv4 Source Guard
- IPv6 Source Guard
- ARP Inspection
- Application Filter
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting Community Access Strings
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Setting a Time Range
- Ethernet Ring Protection Switching
- MLAG Configuration
- OAM Configuration
- LBD Configuration
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query for IPv4)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering IGMP Packets on an Interface
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Configuring MLD Snooping and Query Parameters
- Setting Immediate Leave Status for MLD Snooping per Interface
- Specifying Static Interfaces for an IPv6 Multicast Router
- Assigning Interfaces to IPv6 Multicast Services
- Filtering MLD Query Packets on an Interface
- Showing MLD Snooping Groups and Source List
- Displaying MLD Snooping Statistics
- Filtering and Throttling MLD Groups
- Multicast VLAN Registration for IPv4
- IP Tools
- IP Configuration
- General IP Routing
- IP Services
- Appendices
Chapter 13
| Basic Administration Protocols
Ethernet Ring Protection Switching
– 495 –
◆ Physical Ring – Specifies the name of the physical ring on which the
configured instance runs.
◆ West/East – Connects to next ring node to the west/east.
Each node must be connected to two neighbors on the ring. For convenience,
the ports connected are referred to as east and west ports. Alternatively, the
closest neighbor to the east should be the next node in the ring in a clockwise
direction, and the closest neighbor to the west should be the next node in the
ring in a counter-clockwise direction.
◆ Interface – The port or trunk attached to the west or east ring port.
Note that a ring port cannot be configured as a member of a spanning tree, a
dynamic trunk, or a static trunk.
◆ Port State – Once configured, this field shows the operational state of the ring
ports for this node:
■
Blocking – The transmission and reception of traffic is blocked and the
forwarding of R-APS messages is blocked, but the transmission of locally
generated R-APS messages is allowed and the reception of all R-APS
messages is allowed.
■
Forwarding – The transmission and reception of traffic is allowed;
transmission, reception and forwarding of R-APS messages is allowed.
■
Down – The interface is not linked up.
■
Unknown – The interface is not in a known state.
◆ Local SF – Shows if a signal fault exists on a link to the local node.
◆ Local FS – Shows if a forced switch command was issued on this interface.
◆ Local MS – Shows if a manual switch command was issued on this interface.
◆ MEP – Specifies the MEPs used to monitor the link on a ring node.
◆ RPL – If node is connected to the RPL, this shows by which interface.
◆ Inclusion VLANs – Specifies VLAN groups that are to be on the inclusion list of
an the ERPS instance. VLANs that are on the inclusion list are protected by the
ERPS instance. Any VLAN not listed on either the inclusion or exclusion list will
be blocked on ring ports.
◆ Status – Activates the current ERPS instance. (Default: Disabled)
Before enabling a ring instance, the global ERPS function should be enabled
see (“ERPS Global Configuration” on page 480), the physical ring east and west
ports configured on each node, the RPL owner specified, and the control VLAN
configured.
Once enabled, the RPL owner node and non-owner node state machines will
start, and the ring will enter idle state if no signal failures are detected.