Web Management Guide-R02
Table Of Contents
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Using the Web Interface
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Configuring CPU Guard
- Displaying Memory Utilization
- Resetting the System
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA (Authentication, Authorization and Accounting)
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- DHCP Snooping
- DHCPv6 Snooping
- ND Snooping
- IPv4 Source Guard
- IPv6 Source Guard
- ARP Inspection
- Application Filter
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting Community Access Strings
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Setting a Time Range
- Ethernet Ring Protection Switching
- MLAG Configuration
- OAM Configuration
- LBD Configuration
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query for IPv4)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering IGMP Packets on an Interface
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Configuring MLD Snooping and Query Parameters
- Setting Immediate Leave Status for MLD Snooping per Interface
- Specifying Static Interfaces for an IPv6 Multicast Router
- Assigning Interfaces to IPv6 Multicast Services
- Filtering MLD Query Packets on an Interface
- Showing MLD Snooping Groups and Source List
- Displaying MLD Snooping Statistics
- Filtering and Throttling MLD Groups
- Multicast VLAN Registration for IPv4
- IP Tools
- IP Configuration
- General IP Routing
- IP Services
- Appendices
Chapter 12
| Security Measures
IPv6 Source Guard
– 391 –
Figure 246: Showing the IPv4 Source Guard Binding Table
IPv6 Source Guard
IPv6 Source Guard is a security feature that filters IPv6 traffic on non-routed, Layer 2
network interfaces based on manually configured entries in the IPv6 Source Guard
table, or dynamic entries in the Neighbor Discovery Snooping table or DHCPv6
Snooping table when either snooping protocol is enabled (refer to the DHCPv6
Snooping commands in the CLI Reference Guide). IPv6 source guard can be used to
prevent traffic attacks caused when a host tries to use the IPv6 address of a
neighbor to access the network. This section describes how to configure IPv6
Source Guard.
Configuring Ports for
IPv6 Source Guard
Use the Security > IPv6 Source Guard > Port Configuration page to filter inbound
traffic based on the source IPv6 address stored in the binding table.
IPv6 Source Guard is used to filter traffic on an insecure port which receives
messages from outside the network or fire wall, and therefore may be subject to
traffic attacks caused by a host trying to use the IPv6 address of a neighbor.
Command Usage
◆ Setting source guard mode to SIP (Source IP) enables this function on the
selected port. Use the SIP option to check the VLAN ID, IPv6 global unicast
source IP address, and port number against all entries in the binding table.
◆ After IPv6 source guard is enabled on an interface, the switch initially blocks all
IPv6 traffic received on that interface, except for ND packets allowed by ND
snooping and DHCPv6 packets allowed by DHCPv6 snooping. A port access
control list (ACL) is applied to the interface. Traffic is then filtered based upon
dynamic entries learned via ND snooping or DHCPv6 snooping, or static
addresses configured in the source guard binding table. The port allows only
IPv6 traffic with a matching entry in the binding table and denies all other IPv6
traffic.