Web Management Guide-R02
Table Of Contents
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Using the Web Interface
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Configuring CPU Guard
- Displaying Memory Utilization
- Resetting the System
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA (Authentication, Authorization and Accounting)
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- DHCP Snooping
- DHCPv6 Snooping
- ND Snooping
- IPv4 Source Guard
- IPv6 Source Guard
- ARP Inspection
- Application Filter
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting Community Access Strings
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Setting a Time Range
- Ethernet Ring Protection Switching
- MLAG Configuration
- OAM Configuration
- LBD Configuration
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query for IPv4)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering IGMP Packets on an Interface
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Configuring MLD Snooping and Query Parameters
- Setting Immediate Leave Status for MLD Snooping per Interface
- Specifying Static Interfaces for an IPv6 Multicast Router
- Assigning Interfaces to IPv6 Multicast Services
- Filtering MLD Query Packets on an Interface
- Showing MLD Snooping Groups and Source List
- Displaying MLD Snooping Statistics
- Filtering and Throttling MLD Groups
- Multicast VLAN Registration for IPv4
- IP Tools
- IP Configuration
- General IP Routing
- IP Services
- Appendices
Chapter 12
| Security Measures
DHCP Snooping
– 365 –
DHCP Snooping
Global Configuration
Use the Security > DHCP Snooping (Configure Global) page to enable DHCP
Snooping globally on the switch, or to configure MAC Address Verification.
Parameters
These parameters are displayed:
General
◆ DHCP Snooping Status – Enables DHCP snooping globally. (Default: Disabled)
◆ DHCP Snooping MAC-Address Verification – Enables or disables MAC
address verification. If the source MAC address in the Ethernet header of the
packet is not same as the client's hardware address in the DHCP packet, the
packet is dropped. (Default: Enabled)
◆ DHCP Snooping Rate Limit – Sets the maximum number of DHCP packets
that can be trapped by the switch for DHCP snooping. (Range: 1-2048 packets/
second)
Information
◆ DHCP Snooping Information Option Status – Enables or disables DHCP
Option 82 information relay. (Default: Disabled)
◆ DHCP Snooping Information Option Sub-option Format – Enables or
disables use of sub-type and sub-length fields in circuit-ID (CID) and remote-ID
(RID) in Option 82 information. (Default: Enabled)
◆ DHCP Snooping Information Option Remote ID – Specifies the MAC address,
IP address, or arbitrary identifier of the requesting device (i.e., the switch in this
context).
■
MAC Address – Inserts a MAC address in the remote ID sub-option for the
DHCP snooping agent (i.e., the MAC address of the switch’s CPU). This
attribute can be encoded in Hexadecimal or ASCII.
■
IP Address – Inserts an IP address in the remote ID sub-option for the
DHCP snooping agent (i.e., the IP address of the management interface).
This attribute can be encoded in Hexadecimal or ASCII.
■
string - An arbitrary string inserted into the remote identifier field.
(Range: 1-32 characters)
◆ DHCP Snooping Information Option Remote ID TR101 VLAN Field – Adds
“:VLAN” in TR101 field for untagged packets.
The format for TR101 option 82 is: “<IP> eth <SID>/<PORT>[:<VLAN>]”. Note
that the SID (Switch ID) is always 0. By default the PVID is added to the end of
the TR101 field for untagged packets. For tagged packets, the VLAN ID is always
added.