Web Management Guide-R02
Table Of Contents
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Using the Web Interface
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Configuring CPU Guard
- Displaying Memory Utilization
- Resetting the System
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA (Authentication, Authorization and Accounting)
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- DHCP Snooping
- DHCPv6 Snooping
- ND Snooping
- IPv4 Source Guard
- IPv6 Source Guard
- ARP Inspection
- Application Filter
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting Community Access Strings
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Setting a Time Range
- Ethernet Ring Protection Switching
- MLAG Configuration
- OAM Configuration
- LBD Configuration
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query for IPv4)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering IGMP Packets on an Interface
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Configuring MLD Snooping and Query Parameters
- Setting Immediate Leave Status for MLD Snooping per Interface
- Specifying Static Interfaces for an IPv6 Multicast Router
- Assigning Interfaces to IPv6 Multicast Services
- Filtering MLD Query Packets on an Interface
- Showing MLD Snooping Groups and Source List
- Displaying MLD Snooping Statistics
- Filtering and Throttling MLD Groups
- Multicast VLAN Registration for IPv4
- IP Tools
- IP Configuration
- General IP Routing
- IP Services
- Appendices
Chapter 10
| Quality of Service
Creating QoS Policies
– 271 –
■
Set IP DSCP – Decreases DSCP priority for out of conformance
traffic. (Range: 0-63)
■
Drop – Drops out of conformance traffic.
■
trTCM (Police Meter) – Defines the committed information rate (CIR, or
maximum throughput), peak information rate (PIR), and their associated
burst sizes – committed burst size (BC, or burst rate) and peak burst size
(BP), and the action to take for traffic conforming to the maximum
throughput, exceeding the maximum throughput but within the peak
information rate, or exceeding the peak information rate. In addition to the
actions defined by this command to transmit, remark the DSCP service
value, or drop a packet, the switch will also mark the two color bits used to
set the drop precedence of a packet.
The color modes include “Color-Blind” which assumes that the packet
stream is uncolored, and “Color-Aware” which assumes that the incoming
packets are pre-colored. The functional differences between these modes
is described at the beginning of this section under “trTCM Police Meter.”
■
Committed Information Rate (CIR) – Rate in kilobits per second.
(Range: 0-10000000 kbps at a granularity of 64 kbps or maximum port
speed, whichever is lower)
The rate cannot exceed the configured interface speed.
■
Committed Burst Size (BC) – Burst in bytes. (Range: 64-16000000 at a
granularity of 4k bytes)
The burst size cannot exceed 16 Mbytes.
■
Peak Information Rate (PIR) – Rate in kilobits per second.
(Range: 0-1000000 kbps at a granularity of 64 kbps or maximum port
speed, whichever is lower)
The rate cannot exceed the configured interface speed.
■
Peak Burst Size (BP) – Burst size in bytes.
(Range: 64-16000000 at a granularity of 4k bytes)
The burst size cannot exceed 16 Mbytes.
■
Conform – Specifies that traffic conforming to the maximum rate (CIR)
will be transmitted without any change to the DSCP service level.
■
Transmit – Transmits in-conformance traffic without any change to
the DSCP service level.
■
Exceed – Specifies whether traffic that exceeds the maximum rate (CIR)
but is within the peak information rate (PIR) will be dropped or the
DSCP service level will be reduced.