Web Management Guide-R05
Table Of Contents
- ECS4810-12M Gigabit Ethernet Switch
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Using the Web Interface
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Displaying Memory Utilization
- Resetting the System
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA (Authentication, Authorization and Accounting)
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Setting a Time Range
- Showing TCAM Utilization
- Setting the ACL Name and Type
- Configuring a Standard IPv4 ACL
- Configuring an Extended IPv4 ACL
- Configuring a Standard IPv6 ACL
- Configuring an Extended IPv6 ACL
- Configuring a MAC ACL
- Configuring an ARP ACL
- Binding a Port to an Access Control List
- Configuring ACL Mirroring
- Showing ACL Hardware Counters
- ARP Inspection
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- IP Source Guard
- DHCP Snooping
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Setting Community Access Strings
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Switch Clustering
- Ethernet Ring Protection Switching
- Connectivity Fault Management
- Configuring Global Settings for CFM
- Configuring Interfaces for CFM
- Configuring CFM Maintenance Domains
- Configuring CFM Maintenance Associations
- Configuring Maintenance End Points
- Configuring Remote Maintenance End Points
- Transmitting Link Trace Messages
- Transmitting Loop Back Messages
- Transmitting Delay-Measure Requests
- Displaying Local MEPs
- Displaying Details for Local MEPs
- Displaying Local MIPs
- Displaying Remote MEPs
- Displaying Details for Remote MEPs
- Displaying the Link Trace Cache
- Displaying Fault Notification Settings
- Displaying Continuity Check Errors
- OAM Configuration
- UDLD Configuration
- IP Configuration
- IP Services
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query for IPv4)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering IGMP Query and Report Packets
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Multicast VLAN Registration for IPv4
- Multicast VLAN Registration for IPv6
- Appendices
- Glossary
- Index
Chapter 2
| Using the Web Interface
Navigating the Web Browser Interface
– 65 –
Remote Loopback Performs a loopback test on the specified port 512
UDLD UniDirectional Link Detection 515
Configure Global Configures the message probe interval, detection interval, and recovery
interval
515
Configure Interface Enables UDLD and aggressive mode which reduces the shut-down delay
after loss of bidirectional connectivity is detected
515
Show Information Displays UDLD neighbor information, including neighbor state,
expiration time, and protocol intervals
515
IP 521
General
Ping Sends ICMP echo request packets to another node on the network 521
Trace Route Shows the route packets take to the specified
destination
523
ARP Shows dynamically learned entries in the IP routing table 524
IPv6 Configuration 529
Configure Global Sets an IPv6 default gateway for traffic with no known next hop 530
Configure Interface Configures IPv6 interface address using auto-configuration or link-local
address, and sets related protocol settings
531
Add IPv6 Address Adds an global unicast, EUI-64, or link-local IPv6 address to an interface 536
Show IPv6 Address Show the IPv6 addresses assigned to an interface 538
Show IPv6 Neighbor Cache Displays information in the IPv6 neighbor discovery cache 540
Show Statistics 541
IPv6 Shows statistics about IPv6 traffic 541
ICMPv6 Shows statistics about ICMPv6 messages 541
UDP Shows statistics about UDP messages 541
Show MTU Shows the maximum transmission unit (MTU) cache for destinations
that have returned an ICMP packet-too-big message along with an
acceptable MTU to this switch
547
IP Service 549
DNS Domain Name Service 549
General 549
Configure Global Enables DNS lookup; defines the default domain name appended to
incomplete host names
549
Add Domain Name Defines a list of domain names that can
be appended to incomplete host names
550
Show Domain Names Shows the configured domain name list 550
Add Name Server Specifies IP address of name servers for dynamic lookup 552
Show Name Servers Shows the name server address list 552
Table 4: Switch Main Menu (Continued)
Menu Description Page