Web Management Guide-R05
Table Of Contents
- ECS4810-12M Gigabit Ethernet Switch
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Using the Web Interface
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Displaying Memory Utilization
- Resetting the System
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA (Authentication, Authorization and Accounting)
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Setting a Time Range
- Showing TCAM Utilization
- Setting the ACL Name and Type
- Configuring a Standard IPv4 ACL
- Configuring an Extended IPv4 ACL
- Configuring a Standard IPv6 ACL
- Configuring an Extended IPv6 ACL
- Configuring a MAC ACL
- Configuring an ARP ACL
- Binding a Port to an Access Control List
- Configuring ACL Mirroring
- Showing ACL Hardware Counters
- ARP Inspection
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- IP Source Guard
- DHCP Snooping
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Setting Community Access Strings
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Switch Clustering
- Ethernet Ring Protection Switching
- Connectivity Fault Management
- Configuring Global Settings for CFM
- Configuring Interfaces for CFM
- Configuring CFM Maintenance Domains
- Configuring CFM Maintenance Associations
- Configuring Maintenance End Points
- Configuring Remote Maintenance End Points
- Transmitting Link Trace Messages
- Transmitting Loop Back Messages
- Transmitting Delay-Measure Requests
- Displaying Local MEPs
- Displaying Details for Local MEPs
- Displaying Local MIPs
- Displaying Remote MEPs
- Displaying Details for Remote MEPs
- Displaying the Link Trace Cache
- Displaying Fault Notification Settings
- Displaying Continuity Check Errors
- OAM Configuration
- UDLD Configuration
- IP Configuration
- IP Services
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query for IPv4)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering IGMP Query and Report Packets
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Multicast VLAN Registration for IPv4
- Multicast VLAN Registration for IPv6
- Appendices
- Glossary
- Index
Chapter 2
| Using the Web Interface
Navigating the Web Browser Interface
– 57 –
Priority
Default Priority Sets the default priority for each port or trunk 231
Queue Sets queue mode for the switch; sets the service weight for each queue
that will use a weighted or hybrid mode
232
Trust Mode Selects DSCP or CoS priority processing 240
DSCP to DSCP 238
Configure Maps DSCP values in incoming packets to per-hop behavior and drop
precedence values for internal priority processing
238
Show Shows the DSCP to DSCP mapping list 238
DSCP to CoS 240
Configure Maps CoS/CFI values in incoming packets to per-hop behavior and drop
precedence values for priority processing
240
Show Shows the CoS to DSCP mapping list 240
CoS to DSCP 241
Configure Maps CoS/CFI values in incoming packets to per-hop behavior and drop
precedence values for priority processing
241
Show Shows the CoS to DSCP mapping list 241
PHB to Queue 235
Configure Maps internal per-hop behavior values to hardware queues 235
Show Shows the PHB to Queue mapping list 235
DiffServ 245
Configure Class 246
Add Creates a class map for a type of traffic 246
Show Shows configured class maps 246
Modify Modifies the name of a class map 246
Add Rule Configures the criteria used to classify ingress traffic 246
Show Rule Shows the traffic classification rules for a class map 246
Configure Policy 250
Add Creates a policy map to apply to multiple interfaces 250
Show Shows configured policy maps 250
Modify Modifies the name of a policy map 250
Add Rule Sets the boundary parameters used for monitoring inbound traffic, and
the action to take for conforming and non-conforming traffic
250
Show Rule Shows the rules used to enforce bandwidth policing for a policy map 250
Configure Bundle Sets the maximum ingress rate for a group of traffic flows 250
Show Bundle Shows the maximum ingress rate for a group of traffic flows 250
Configure Interface Applies a policy map to an ingress port 261
Table 4: Switch Main Menu (Continued)
Menu Description Page