Web Management Guide-R05
Table Of Contents
- ECS4810-12M Gigabit Ethernet Switch
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Using the Web Interface
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Displaying Memory Utilization
- Resetting the System
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA (Authentication, Authorization and Accounting)
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Setting a Time Range
- Showing TCAM Utilization
- Setting the ACL Name and Type
- Configuring a Standard IPv4 ACL
- Configuring an Extended IPv4 ACL
- Configuring a Standard IPv6 ACL
- Configuring an Extended IPv6 ACL
- Configuring a MAC ACL
- Configuring an ARP ACL
- Binding a Port to an Access Control List
- Configuring ACL Mirroring
- Showing ACL Hardware Counters
- ARP Inspection
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- IP Source Guard
- DHCP Snooping
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Setting Community Access Strings
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Switch Clustering
- Ethernet Ring Protection Switching
- Connectivity Fault Management
- Configuring Global Settings for CFM
- Configuring Interfaces for CFM
- Configuring CFM Maintenance Domains
- Configuring CFM Maintenance Associations
- Configuring Maintenance End Points
- Configuring Remote Maintenance End Points
- Transmitting Link Trace Messages
- Transmitting Loop Back Messages
- Transmitting Delay-Measure Requests
- Displaying Local MEPs
- Displaying Details for Local MEPs
- Displaying Local MIPs
- Displaying Remote MEPs
- Displaying Details for Remote MEPs
- Displaying the Link Trace Cache
- Displaying Fault Notification Settings
- Displaying Continuity Check Errors
- OAM Configuration
- UDLD Configuration
- IP Configuration
- IP Services
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query for IPv4)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering IGMP Query and Report Packets
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Multicast VLAN Registration for IPv4
- Multicast VLAN Registration for IPv6
- Appendices
- Glossary
- Index
Chapter 13
| Basic Administration Protocols
Ethernet Ring Protection Switching
– 449 –
Hold-off timer to filter out intermittent link faults, and the WTR timer to verify
that the ring has stabilized before blocking the RPL after recovery from a signal
failure.
5.
Configure the ERPS Control VLAN (Configure Domain – Configure Details):
Specify the Control VLAN (CVLAN) used to pass R-APS ring maintenance
commands. The CVLAN must NOT be configured with an IP address. In addition,
only ring ports may be added to the CVLAN (prior to configuring the VLAN as a
CVLAN). No other ports can be members of this VLAN (once set as a CVLAN).
Also, the ring ports of the CVLAN must be tagged. Failure to observe these
restrictions can result in a loop in the network.
6.
Enable ERPS (Configure Global): Before enabling a ring as described in the next
step, first globally enable ERPS on the switch. If ERPS has not yet been enabled
or has been disabled, no ERPS rings will work.
7.
Enable an ERPS ring (Configure Domain – Configure Details): Before an ERPS
ring can work, it must be enabled. When configuration is completed and the
ring enabled, R-APS messages will start flowing in the control VLAN, and
normal traffic will begin to flow in the data VLANs. A ring can be stopped by
disabling the Admin Status on any node.
8.
Display ERPS status information (Configure Domain – Show): Display ERPS
status information for all configured rings.
Configuration Limitations for ERPS
The following configuration limitations apply to ERPS:
◆
The switch supports up to six ERPS rings – each ring must have one Control
VLAN, and at most 255 Data VLANs.
◆
Ring ports can not be a member of a trunk, nor an LACP-enabled port.
◆
Dynamic VLANs are not supported as protected data ports.
◆
Exclusive use of STP or ERPS on any port.
◆
The switch takes about 350 ms to detect link-up on 1000Base-T copper ports,
so the convergence time on this port type is more than 50 ms.