Web Management Guide
Table Of Contents
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Using the Web Interface
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Configuring CPU Guard
- Displaying Memory Utilization
- Resetting the System
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA (Authentication, Authorization and Accounting)
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- DHCP Snooping
- DHCPv6 Snooping
- IPv4 Source Guard
- IPv6 Source Guard
- ARP Inspection
- Application Filter
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting Community Access Strings
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Setting a Time Range
- Ethernet Ring Protection Switching
- OAM Configuration
- LBD Configuration
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query for IPv4)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering IGMP Packets on an Interface
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Configuring MLD Snooping and Query Parameters
- Setting Immediate Leave Status for MLD Snooping per Interface
- Specifying Static Interfaces for an IPv6 Multicast Router
- Assigning Interfaces to IPv6 Multicast Services
- Filtering MLD Query Packets on an Interface
- Showing MLD Snooping Groups and Source List
- Displaying MLD Snooping Statistics
- Filtering and Throttling MLD Groups
- Multicast VLAN Registration for IPv4
- IP Tools
- IP Configuration
- General IP Routing
- IP Services
- Appendices
Chapter 2
| Using the Web Interface
Navigating the Web Browser Interface
– 60 –
Administration 395
Log 396
System 396
Configure Global Stores error messages in local memory 396
Show System Logs Shows logged error messages 396
Remote Configures the logging of messages to a remote logging process 398
SMTP Sends an SMTP client message to a participating server 399
LLDP 401
Configure Global Configures global LLDP timing parameters 401
Configure Interface 403
Configure General Sets the message transmission mode; enables SNMP notification; and
sets the LLDP attributes to advertise
403
Add CA-Type Specifies the physical location of the device attached to an interface 407
Show Local Device Information 409
General Displays general information about the local device 409
Port/Trunk Displays information about each interface 409
Show Remote Device Information 413
Port/Trunk Displays information about a remote device connected to a port on this
switch
413
Port/Trunk Details Displays detailed information about a remote device connected to this
switch
413
Show Device Statistics 421
General Displays statistics for all connected remote devices 421
Port/Trunk Displays statistics for remote devices on a selected port or trunk 421
SNMP Simple Network Management Protocol 423
Configure Global Enables SNMP agent status, and sets related trap functions 426
Configure Engine 428
Set Engine ID Sets the SNMP v3 engine ID on this switch 428
Add Remote Engine Sets the SNMP v3 engine ID for a remote device 429
Show Remote Engine Shows configured engine ID for remote devices 429
Configure View 430
Add View Adds an SNMP v3 view of the OID MIB 430
Show View Shows configured SNMP v3 views 430
Add OID Subtree Specifies a part of the subtree for the selected view 430
Show OID Subtree Shows the subtrees assigned to each view 430
Table 4: Switch Main Menu (Continued)
Menu Description Page