ECS4510-Series_Quick Start Guide-R03

ManualsBrandsEdgecore Networks ManualsEnterpriseL2+ Gigabit Ethernet Stackable Switch

– 1 –

Quick Start Guide

28/52-Port L2+ Stackable Gigabit Ethernet Switch

ECS4510-28T / ECS4510-28P / ECS4510-28F / ECS4510-28F-DC

ECS4510-52T / ECS4510-52P

The ECS4510-28T, ECS4510-28P, ECS4510-52T, and ECS4510-52P are stackable

Layer 2+ switches that provide 24/48 10/100/1000BASE-T RJ-45 ports, and two 10

Gigabit (10G) Small Form Factor Pluggable Plus (SFP+) slots that support 1G and

10G transceivers. The ECS4510-28F and ECS4510-28F-DC are Layer 2+ switches that

provide 22 SFP 1G transceiver slots, two combination Gigabit RJ-45/SFP ports, and

two 10G SFP+ slots. The ECS4510-28P and ECS4510-52P also provide Power-over-

Ethernet Plus (PoE+) capability on the RJ-45 ports.

All switches also provide one rear-panel slot for a dual-port 10G hot-swappable

expansion module.

ECS4510-28P

ECS4510-28F

ECS4510-52T

ECS4510-52P

ECS4510-28T

ECS4510-28F-DC

E072015-CS-R03

150200000991A

www.edge-core.com

Summary of content (8 pages)

PAGE 1
Q ui ck Sta r t G u i d e 28/52-Port L2+ Stackable Gigabit Ethernet Switch ECS4510-28T / ECS4510-28P / ECS4510-28F / ECS4510-28F-DC ECS4510-52T / ECS4510-52P The ECS4510-28T, ECS4510-28P, ECS4510-52T, and ECS4510-52P are stackable Layer 2+ switches that provide 24/48 10/100/1000BASE-T RJ-45 ports, and two 10 Gigabit (10G) Small Form Factor Pluggable Plus (SFP+) slots that support 1G and 10G transceivers.
PAGE 2
Quick Start Guide Note: For detailed switch installation information, refer to the Installation Guide, which is on the Documentation CD included with the switch. Note: For Safety and Regulatory information, refer to the Safety and Regulatory Information document included with the switch. 1. Unpack the Switch Unpack the switch and check the package contents.
PAGE 3
Quick Start Guide 3. Ground the Switch Before powering on the switch, ground the switch to earth. Ensure the rack on which the switch is to be mounted is properly grounded and in compliance with ETSI ETS 300 253. Verify that there is a good electrical connection to the grounding point on the rack (no paint or isolating surface treatment.).
PAGE 4
Quick Start Guide 1 1 Plug the AC power cord into the socket on the rear of the switch. If you have purchased an optional Redundant Power Supply for use with the ECS4510-52P, connect it to the switch and to an AC power source now, following the instructions included with the package. Note: The ECS4510-52P maximum power consumption is reduced to 780 W when the device is powered from a connected RPS.
PAGE 5
Quick Start Guide 1 1 Plug the DC power cable into the socket on the rear of the switch. 5. Verify Switch Verify basic switch operation by checking the system LEDs. Operation When operating normally, the Diag and Power LEDs should both be on green. 1 1 System Status LEDs. 6. Make Initial At this point you may need to make a few basic switch configuration changes Configuration before connecting to the network. It is suggested to connect to the switch console Changes port to perform this task.
PAGE 6
Quick Start Guide 1 2 1 Console Port. 2 Console Cable. For information on initial switch configuration, refer to the CLI Reference Guide. 7. Connect Network Install SFP/SFP+ transceivers and connect network cables to port interfaces: Cables ◆ For RJ-45 ports, use 100-ohm Category 5, 5e or better twisted-pair cable for 1000BASE-T connections, Category 5 or better for 100BASE-TX connections, and Category 3 or better for 10BASE-T connections.
PAGE 7
Quick Start Guide 1 2 1 10/100/1000BASE-T RJ-45 Port. 2 Twisted-pair Cable with RJ-45 Plug. Software Release Notice For ECS4510-28F-DC configuration, refer to the revised version of the Management Guide at the following link: www.edge-core.com/DownDtl.
PAGE 8
Quick Start Guide Hardware Specifications Item Specification Chassis Specifications Size (W x D x H) ECS4510-28T/P/F: 44.0 x 31.5 x 4.4 cm (17.3 x 12.4 x 1.7 in.) ECS4510-52T/P: 44.0 x 39.1 x 4.4 cm (17.3 x 15.4 x 1.7 in.) Weight ECS4510-28T: 3.7 kg (8.16 lb) ECS4510-28P: 4.95 kg (10.91 lb) ECS4510-28F/F-DC: 3.8 kg (8.38 lb) ECS4510-52T: 4.8 kg (10.52 lb) ECS4510-52P: 6.58 kg (14.